SignaMax 065-1895 series User manual

065-1895 series Hardened Media Converter
User’s Manual 1
Preface
This hardened media converter provides an affordable solution for rugged
and outdoor environments, transportation roadside cabinets, industrial floor
operations, multi-tenant dwellings, or Fiber To The Home (FTTH)
applications. It is the media converter of choice for harsh environments
with space constraints. It is capable of operating at temperature extremes
of -29° F to 165° F (-34° C to +74° C).
Plug-and-Play Solution:
The Signamax 065-1895 series hardened media converter is a plug-and-
play media converter with a compact case size. There is no complicated
software set up required.
This manual describes how to install and use the Signamax 065-1895
series hardened media converters with the Link Fault Signaling (LFS)
function. The converters introduced here provide one channel of media
conversion between 1000BaseT and 1000BaseSX/LX.
These converters fully comply with IEEE802.3ab 1000BaseT and
IEEE802.3z 1000BaseSX/LX standards.
In this manual, you will find:
yProduct overview
yFeatures of the of the 065-1895 series media converters
yIllustrative LED functions
yInstallation instructions
ySpecifications

065-1895 series Hardened Media Converter
2 User’s Manual
Table of Contents
Preface 1
Table of Contents 2
Introduction 3
PRODUCT OVERVIEW ......................................................................................... 3
PRODUCT FEATURES.......................................................................................... 4
PACKING LIST...................................................................................................... 4
One-Channel Media Converter 5
PORTS.................................................................................................................. 5
PORT SETTINGS.................................................................................................. 5
FRONT PANEL &LEDS....................................................................................... 6
Installation 7
SELECTING A SITE FOR THE EQUIPMENT .......................................................... 7
DIN RAIL MOUNTING .......................................................................................... 7
CONNECTING TO POWER.................................................................................... 8
Specifications 10

065-1895 series Hardened Media Converter
User’s Manual 3
Introduction
The media converter provides one channel for media conversion between
1000BaseT and 1000BaseSX/LX with the link-fault-pass-through function.
This hardened fiber optic solution is perfectly fitted in the industrial
applications or rugged environment.
Product Overview

065-1895 series Hardened Media Converter
4 User’s Manual
Product Features
yMeets NEMA TS1/TS2 environmental requirements such as
temperature, shock, and vibration for traffic control equipment
yMeets IEC61000-6-2 EMC Generic Standard Immunity for industrial
environment
yOne-channel media conversion between 1000BaseT and
1000BaseSX/LX
yFiber media allows Multi-mode fiber or Single-mode fiber using SC
yThe fiber port should be set to (forced full duplex mode, forced full duplex
mode) or (auto mode, forced full duplex mode) when two 1000BaseT
and 1000BaseSX/LX one-channel media converters are connected to
each other via fiber port
yAuto negotiation and Auto MDIX on TX port
yOne DIP switch for configuring Link Fault Signaling (LFS), fixed speed,
full/half duplex, and link down alarm
yNon-blocking full wire-speed forwarding rate
yBack-pressure & IEEE802.3x compliant flow control
yAlarms for power and port link down failure by relay output
yRedundant 1.5A 24VDC Terminal Block power inputs; or 3A DC JACK
12VDC with provided 100-240VAC external power supply
ySupports Din-rail or panel mounting installation
yFront panel status LEDs
Packing List
When you unpack this product’s package, you will find the items listed
below. Please inspect the contents, and report any apparent damage or
missing items immediately to our authorized reseller.
yThe Signamax 065-1895 series Hardened Media Converter
yUser’s Manual on CD-ROM
ySignamax 065-1895 series Hardened Media Converter Quick Installation
Guide
yAC to DC Power Adaptor and Power Cable (optional 12 V DC powered
models only)

065-1895 series Hardened Media Converter
User’s Manual 5
One-Channel Media Converter
Ports
The Converter provides one copper port and one fiber port. The fiber port
provides options of Multi-mode fiber or Single-mode fiber using an SC
connector.
The copper port uses RJ-45 connector, auto-MDIX, and auto negotiates.
Port Settings
Port settings are made very simple by means of a DIP (Dual Inline
Package) switch on the front panel of the hardened media converter.
Default DIP switch settings:
1 2 3 4 1
0
DIP Switch
There are four pins on the DIP switch for port settings. Refer to the table below for more
details.
DIP switch No. 0 1
1 Disable Link Fault Signaling Enable Link Fault Signaling
2 Enable auto negotiation for
fiber port Enable forced mode for fiber port
3 Disable link down alarm for
copper port Enable link down alarm for copper port
4 Disable link down alarm for
fiber port Enable link down alarm for fiber port

065-1895 series Hardened Media Converter
6 User’s Manual
Front Panel & LEDs
LED Indicators
The LED indicators give you instant feedback on converter status:
LED’s State Indication
Steady Power or ports function abnormalFAULT
Off Power and ports function normal
Steady Power on
PWR stands for POWER
PWR1
PWR2 Off Power off
Steady A valid network connection established for copper port
LNK stands for LINK
LNKC
Off No valid network connection established for copper port
Steady A valid network connection established for fiber port
LNK stands for LINK
LNKF
Off No valid network connection established for fiber port
Flashing Transmitting data
TX stands for TRANSMIT
TX
Off No transmitting data
Flashing Receiving data
RX stands for RECEIVE
RX
Off No data being received

065-1895 series Hardened Media Converter
User’s Manual 7
Installation
This chapter gives step-by-step installation instructions for the Converter.
Selecting a Site for the Equipment
As with any electric device, you should place the equipment where it will
not be subjected to extreme temperatures, humidity, or electromagnetic
interference. Specifically, the site you select should meet the following
requirements:
yThe ambient temperature should be between -29° to 165° Fahrenheit (-34°
to +74° Celsius).
yThe relative humidity should be less than 95 percent, non-condensing.
ySurrounding electrical devices should not exceed the electromagnetic field
(RFC) standards for IEC 801-3, Level 2 (3V/M) field strength.
yMake sure that the equipment receives adequate ventilation. Do not block
the ventilation holes of the equipment.
yThe power outlet should be within 1.8 meters of the product.
DIN Rail Mounting
Fix the DIN rail attachment plate to the back panel of the media converter.
Installation: Place the media converter on the DIN rail from above using the
slot. Push the front of the media converter toward the mounting surface
until it audibly snaps into place.
Removal: Pull out the lower edge and then remove the media converter
from the DIN rail.

065-1895 series Hardened Media Converter
8 User’s Manual
Connecting to Power
Redundant 1.5A 24VDC power inputs or 3A 12VDC Jack:
3A 12VDC Jack
Step 1: Connect the supplied AC to DC power adapter to the receptacle on
the topside of the media converter.
Step 2: Connect the power cord to the AC to DC power adapter and attach
the plug into a standard AC outlet with the appropriate AC voltage.
Redundant 1.5A 24VDC Power Inputs
There are two pairs of 1.5A 24VDC power sources that can be used to
power up this device. You only need to have one power source connected
to run the media converter.
Step 1: Connect the DC power cord to the plug-able terminal block on the
media converter, and then plug it into a standard DC outlet.
Step 2: In order to shut down the media converter, disconnect the power
cord.

065-1895 series Hardened Media Converter
User’s Manual 9
Alarms for Power and Port Failure
Step 1: There are two pins on the terminal block that are used for power
failure detection. It provides a normal closed output when the
power source is active. Use this as a dry contact application to
send a signal for power failure detection.
Special note:
The relay output is normal in an open position when there is no power
to the media converter. Please do not connect any power source to this
terminal to prevent a shortage to your power supply.

065-1895 series Hardened Media Converter
10 User’s Manual
Specifications
Applicable Standards IEEE 802.3ab 1000BaseT
IEEE 802.3z 1000BaseSX/LX
Fixed Ports 1 copper port, 1 fiber port
2000Mbps for full-duplexSpeed 1000BaseT
1000BaseSX/LX 2000Mbps for full-duplex
Forwarding rate 1,488,000pps for 1000Mbps
4-pair UTP/STP Cat. 5 up to 100m
Cable 1000BaseT
1000BaseSX/LX MMF (50 or 62.5µm), SMF (9 or 10µm)
Per Unit- (3 LEDs): PWR1, PWR2, FAULTLED Indicators
Per Port- Copper (3 LEDs): LNKC, TX, RX
Fiber (3 LEDs): LNKF, TX, RX
Dimensions W50 × D110 x H136 mm
Weight 0.6 Kg
Power DC Jack: 3A 12VDC, External AC/DC
required
Terminal Block: 1.5A 24VDC, 10-48VDC
Power Consumption 5W Max.
Operating Temperature -34°C ~ 74°C
Storage Temperature -45°C ~ 93°C
Humidity 10 ~ 95%, non-condensing
Safety UL 60950, EN60950, IEC 60950,
IEC 61000-6-2
Emissions FCC Part 15, Class A
CE: EN55022 (CISR22 Class A)
EN55024 (CISPR24 Class A)
Standards
ESD Standard (IEC 61000-4-2)
Radiated FRI Standards (IEC 61000-4-3)
Burst Standards (IEC 61000-4-4)
Surge Standards (IEC 61000-4-5)
Induced RFI Standards (IEC 61000-4-6)
Magnetic Field Standards (IEC 61000-4-8)
Voltage Dips Standards (IEC 61000-4-11)
Environmental Test Compliance:
Vibration Resistance (IEC 60068-2-6)
Shock (IEC 60068-2-27)
Free Fall (IEC 60068-2-32)
NEMA TS1/2 Environmental requirements for traffic control equipment