Signature Hardware VICTORIAN User manual

1Victorian Door Knob & Plate Set Installation Instructions
VICTORIAN DOOR KNOB AND PLATE SET
INSTALLATION INSTRUCTIONS
Before you begin, read the installation instructions below. Observe all local building and safety codes. For the following
installation instructions it is assumed that holes for the handle and lock set are pre-drilled.
Unpack and inspect the product for any shipping damages and ensure that none of the required pieces are missing. If
you nd damages, do not install. Contact Customer Service at 1.866.855.2284. If you need assistance or have questions
while installing your door handle and plate set, contact Customer Service.
We recommend consulting a professional if you are unfamiliar with installing hardware xtures. Signature Hardware
accepts no liability for any damage to the handle, lock set, or door, or for personal injury during installation.
TOOLS AND MATERIALS:
Pencil Screwdriver
Wood Chisel
Drill
DUMMY SET INSTALLATION
1. Remove the set screws on the door knobs (B) with the
Allen wrench provided (C) to disconnect the knobs.
2. Position the dummy spindle (E) in the desired
mounting location.
3. Mark the mounting hole locations on the door.
4. Drill pilot holes with the appropriate drill bit for your
installation.
5. Secure the spindle to the door with the provided wood
screws (D).
6. Thread the decorative escutcheon (A) onto the
dummy spindle. Secure to the door with screws.
7. Thread the door knob (B) onto the dummy spindle.
8. Place a set screw in the set screw hole on the side
of the door knob. Use the provided Allen wrench (C) to
secure.
A B
C
D
E

2Victorian Door Knob & Plate Set Installation Instructions
PASSAGE SET INSTALLATION
1. Remove the set screws on the door knobs (B) with the Allen
wrench provided (C) to disconnect the knobs.
2. Insert the latch bolt (E) into the side of the door.
Note: If the attached faceplate is not ush with the door,
carefully chisel out (mortise) some of the door.
3. Drill pilot holes (if necessary) and secure the latch bolt (E)
and faceplate (F) to the door with two wood screws (H).
4. Push the latch bolt in, and insert the passage spindle (I)
through the door.
5. Thread the decorative escutcheon (A) onto the spindle and
attach to the door.
6. Thread the door knob (B) onto the spindle.
7. Place a set screw in the set screw hole on the side of the
door knob. Use the provided Allen wrench (C) to secure.
8. To install the strike plate (G), mark the end of the bolt with
lipstick or paint. Close the door, and turn the handle
several times to mark the door frame.
Note: If the strike plate is not ush with the door, carefully
chisel out (mortise) some of the door.
9. Secure the strike plate to the door frame with the remaining
wood screws.
A
I
H
FE
D
C
B
G

3Victorian Door Knob & Plate Set Installation Instructions
PRIVACY SET INSTALLATION
1. Insert the latch bolt (F) into the side of the door.
Note: If the attached faceplate is not ush with the door,
carefully chisel out (mortise) some of the door.
2. Drill pilot holes (if necessary) and secure the latch bolt (F)
and faceplate (E) to the door with two wood screws (H).
3. Push the latch bolt in, and insert the passage spindle (J)
through the door.
4. Thread the exterior door knob (B), and decorative
escutcheon (A) onto the latch bolt assembly.
5. Fit the interior door knob, and escutcheon over the spindle,
and align the screws holes.
6. Place a set screw in the set screw hole on the side of the
door knob. Use the provided Allen wrench (C) to secure.
7. Hand-thread the mounting screws through the exterior
door knob, and tighten them rmly with a screwdriver.
8. Place a set screw in the set screw hole on the side of the
door knob. Use the provided Allen wrench (C) to secure.
9. Insert the privacy pin (I) through the hole in the interior
door knob into the hole of the latch bolt. Rotate clockwise
to tighten.
10. To install the strike plate (G), mark the end of the bolt with
lipstick or paint. Close the door, and turn the handle
several times to mark the door frame.
Note: If the strike plate is not ush with the door, carefully
chisel out (mortise) some of the door.
11. Secure the strike box (J) and strike plate to the door
frame with the remaining wood screws.
A
GH
FE
D
C
B
J
I