signia VoiceLink User manual

VoiceLink™quick fit guide
For Audiologists and Hearing Care Professionals
signiausa.com

Turning the VoiceLink on/o
• Use the on/o switch (1), to turn the VoiceLink
on or o.
Connecting to VoiceLink
• Turn on the miniTek.
• Press the Audio Source button (ASB) on
upper right, front of miniTek & wait 10
seconds.
• The LED on VoiceLink (5) & streaming
device will stay constant when connection
to streaming device is made; you may need
to press ASB more than once if the LED
continues to blink after 10 seconds.
Changing the mode
• Press the Sound Level Button (2) for about 3
seconds to change the mode.
The LED shines blue for audio mode for TVs,
stereos, etc.
The LED shines purple for microphone mode for
use in noisy environments.
The selected mode remains active when you
turn VoiceLink o and on.
Audio mode
• Use the on/o switch (1) to activate the
Transmitter.
• Be sure that the VoiceLink is in audio mode
(LED shines blue).
If the VoiceLink is in microphone mode (LED
shines purple) press the Sound Level Button (2)
until the LED shines blue.
In audio mode the LED (5) on the VoiceLink
flashes blue while searching for a connection to
your streaming device and shines blue constantly
once a connection is established.
Microphone mode
• Use the on/o switch (1) to activate the
VoiceLink.
• Be sure that the VoiceLink is in microphone
mode (LED shines purple).
If the VoiceLink is in audio mode (LED shines
blue) press the Sound Level Button until the LED
shines purple.
If you want to change to microphone mode
make sure that you connect your microphone
before changing the mode.
Sound level
• Press the Sound Level Button (2) to change
the volume of the audio signal.
The sound level can be adjusted in 5 levels.
The LED flashes blue each time Sound level
button is pushed. 1 flash = lowest volume,
5 flashes = highest volume.
t
t
Connection setup
using VoiceLink
1.On/o switch
2. Sound level/mode switch
3. USB-socket for power supply
4. 2.5 mm stereo socket
5. LED
Please refer to diagram below.
To activate VoiceLink, first connect the remote lapel microphone to the Transmitter 2.5 mm “Aux
in” jack, then push/hold the “Sound level” button for approximately five seconds until the flashing
blue light turns to flashing purple. This will indicate that the VoiceLink microphone operation is
active. Please note: it is important to plug the microphone into the Transmitter before pushing/
holding the Sound level button to properly activate the remote microphone.
PLEASE NOTE –
VoiceLink can be
identified by the
stripe to the left of
the ‘Transmitter’ label.
Transmitter
VoiceLink
Transmitter
TV
Microphone/
Audio-in
Microphone
audio mode
P
Transmitter

VoiceLink, easyTek™,
and miniTek®.
easyTek™ and miniTek® enable your patient to listen to their cell
phone, MP3 player, computer, TV, and other electronic devices
directly through their hearing aids in true stereo, at their preferred
volume without disturbing others. When paired with a streaming
device the VoiceLink™ companion microphone enables them to
hear their companion or a speaker clearly in a busy restaurant or
small gathering as if they were standing inches away.
easyTek +
VoiceLink
miniTek +
VoiceLink
• Connect to multiple
audio devices
• Enhance hearing in
noisy environments
VoiceLink
miniTek
easyTek™

Manufactured by
Sivantos, Inc.
10 Constitution Avenue
Piscataway, NJ 08854
Phone: [phone]
Fax: [phone]
Information in this brochure is subject to change
without notice. Copyright © 2016 Sivantos, Inc.
All rights reserved. Sivantos, Inc. is a Trademark
Licensee of Siemens AG.
The Bluetooth® word mark and logos are owned
by the Bluetooth SIG, Inc. and any use of such
marks by Sivantos, Inc. is under license. Other
trademarks and trade names are those of their
respective owners.
Part #SH201541 5/16 3.0 22B771 1K SI/16836-16
signiausa.com