SIIG Cool Dual SATA to USB 2.0 Docking User manual

1
Introducing the Cool SATA to USB 2.0
The Cool Dual SATA to USB 2.0 Docking is designed to
support USB equipped computers. This adapter
provides large capacity mobile storage using 2.5" or 3.5"
SATA hard disk drives through high-speed, hot-
swapping USB 2.0 interface.
Features and Benefits
• Compliant with USB 1.1 and 2.0 specifications
• Supports data transfer rate up to 480 Mb/s
• Built-in silent cooling fan effectively extends hard
disk drive life
• Dual-bay design works with 2.5- and 3.5-inch (or
mix) SATA hard disk drives
• SupportsSATA1.5/3Gb/sharddiskdrivecapacity
up to 750 GB (2.5-inch) and 2 TB (3.5-inch)
• Plug and Play, no additional drivers needed
• Supports USB hot-swap and hot-plug
System Requirements
• PC or Mac®computer with an available USB port
(USB 2.0 recommended)
• Windows®7 (32-/64-bit) / Vista (32-/64-bit) / XP
(32-/64-bit) / Server 2003 & 2008 (32-/64-bit) /
2000
• Mac OS®X v10.4.8 or higher
Cool Dual SATA to
USB 2.0 Docking
Quick Installation Guide
04-0523B

2
PackageContents
•Cool Dual SATA to USB 2.0 Docking
• Switching power adapter
• USB 2.0 cable (type A to type B) & rubber pads
• Quick installation guide
Layout
Note: You cannot use one hard drive in both
platforms,WindowsandMac. Itis notsupported
Figure 1. Front Layout
Figure 2: Back Layout
SATA Drive Slot
LED (Two LED's stay on
while the unit is on)
On/Off Switch
HDD LED (One LED per HDD;
LED flashes while transfering data)
USB Connector
Power Adapter Jack

3
Hardware Installation
1. Make sure the SATA connectors of the Cool Dual
SATA to USB 2.0 Docking and the SATA hard disk
drive are in alignment. Carefully insert the SATA
hard disk drive into the SATA drive slot.
2. Plug the included switching power adapter into
the power adapter jack ot the Cool Dual SATA to
USB 2.0 Docking, then plug the switching power
adapter into a reliable power source.
3. Use the included USB 2.0 cable to plug the Cool
Dual SATA to USB 2.0 Docking into the computer.
4. Switch on the Cool Dual SATA to USB 2.0 Docking,
make sure that the 3 Power LEDs are lit.
Note: Do not insert or remove a hard disk drive
when the Cool Dual SATA to USB 2.0 Docking is
powered on.
Go to Driver Installation below to complete the
installation.
Driver Installation
Windowsand Macoperating systemswill automatically
detect and install drivers for the Cool Dual SATA to USB
2.0 Docking. No additional driver installation is needed.
Note: In order to get high speed USB 2.0
performance, make sure your USB 2.0 controller
has the correct drivers installed.

4
Using the Cool Dual SATA to USB 2.0 Docking
Windows
One drive icon for each inserted hard disk drive will
appear in Computer or My Computer when the Cool
Dual SATA to USB 2.0 Docking is plugged into a USB
port. The drive(s) act just like a conventional hard disk
drive in your system.
Note: Be careful not to touch the hard disk drive
while in use. It will be warm.
Disconnecting From The Computer
Important: Do not insert or remove a hard disk drive
from the Cool Dual SATA to USB 2.0 Docking while
powered on, doing so will damage the hard disk drive.
BeforeunpluggingtheCoolDualSATAtoUSB 2.0 Docking
from the computer, it must first be stopped, by using
Windows Safely Remove Hardware feature. Follow
the steps below for your version of Windows. The same
rule applies when turning off the Cool Dual SATA to USB
2.0Docking. Notfollowing theinstructions may result in data
corruption, data loss, or damage the hard drive.
Windows 7
1. Verify that the HDD LED(s) are OFF before
proceeding.
2. In the system tray by the system clock, click Show
hidden icons, then click the Safely Remove
Hardware and Eject Media icon.
3. Click USB Mass Storage Device.
4. At Safe to Remove Hardware confirmation box,
you can unplug or turn off the Cool Dual SATA to
USB 2.0 Docking.

5
Windows Vista
1. Verify that the HDD LED(s) are OFF before
proceeding.
2. Double click the Unplug or Eject Hardware icon
located in the system tray.
3. Highlight USB Mass Storage Device, click Stop.
4. Click OK, click OK again, then Close.
5. You can now unplug or turn off the Cool Dual SATA
to USB 2.0 Docking.
Windows XP / Server 2003 & 2008
1. Verify that the HDD LED(s) are OFF before
proceeding.
2. Double click the Safely Remove Hardware icon
located in the system tray.
3. Highlight USB Mass Storage Device, click Stop,
OK then Close.
4. You can now unplug or turn off the Cool Dual SATA
to USB 2.0 Docking.
Windows 2000
1. Verify that the HDD LED(s) are OFF before
proceeding.
2. Double click the Unplug or Eject Hardware icon
located in the system tray.
3. Highlight USB Mass Storage Device, click Stop.
4. Click OK, click OK again, then Close.
5. You can now unplug or turn off the Cool Dual SATA
to USB 2.0 Docking.

6
Mac
One drive icon for each inserted SATA hard disk drive
will appear on the desktop when the Cool Dual SATA to
USB 2.0 Docking is plugged into a USB port. The drive(s)
act just like a conventional hard drive in your system.
Disconnecting From The Computer
BeforeunpluggingtheCoolDual SATAtoUSB2.0Docking
from the computer, drag the drive icon(s) into the
Trashcan and wait for the confirmation box. The same
rule applies when turning off the Cool Dual SATA to USB
2.0 Docking. Not following these instructions may result in
data corruption or damage to the hard drive.

7
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit
ourwebsiteatwww.siig.com andclickSupport. Ouronlinesupport
databaseis updated daily with newdrivers and solutions. Answers
to your questions could be just a few clicks away. You can also
submit questions online and a technical support analysts will
promptlyrespond.
SIIGoffersa2-yearmanufacturerwarrantywiththisproduct. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased it.
B) If your purchase has passed the store's return policy period,
please follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
requestto SIIG RMA. Your RMArequest will be processed,if the
product is determined to be defective, an RMA number will be
issued.
Step 2: After obtaining an RMA number, ship the product.
•Properlypack the product forshipping. All software, cable(s)
andany other accessoriesthat came withthe original package
must be included.
•Clearly write your RMA number on the top of the returned
package. SIIGwillrefuse to accept anyshippingpackage, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
•Youare responsiblefor thecost ofshipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
•SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.

PRODUCT NAME
Cool Dual SATAto USB 2.0 Docking
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undes-
ired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: [phone]
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions(includingSerialATAandUltra ATA Controllers, FireWire,USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebook systems and external peripherals. SIIG continues to grow by
adding A/V and Digital Signage connectivity solutions to our extensive
portfolio. All centered around the distribution and switching of A/V
signals over CAT5/6, these products include matrix switches, distribution
amplifiers, extenders, converters, splitters, cabling, and more.
SIIG is the premier one-stop source of upgrades and is committed to
providinghigh qualityproducts whilekeeping economicaland competitive
prices. High-quality control standards are evident by one of the lowest
defective return rates in the industry. Our products offer comprehensive
user manuals, user-friendly features, and most products are backed by a
lifetime warranty.
SIIG products can be found in many computer retail stores, mail order
catalogs, and e-commerce sites in the Americas, as well as through major
distributors, system integrators, and VARs.
CoolDualSATAto USB2.0 Dockingis atrademark ofSIIG, Inc. SIIGand theSIIG logoare registered
trademarksofSIIG,Inc. MicrosoftandWindowsareregisteredtrademarksofMicrosoftCorporation.
Mac and Mac OS are registered trademarks of Apple, Inc. All other names used in this publication
are for identification only and may be trademarks of their respective owners.
April, 2010 Copyright © 2010 by SIIG, Inc. All rights reserved.