SIIG USB 2.0 to VGA Pro User manual

1
USB 2.0 to VGA Pro
Installation Guide
04-0638H
Introduction
The USB 2.0 to VGA Pro allows you to connect an
extra display to your desktop or notebook.
Key Features and Benefits
• Quickly adds a monitor, LCD or projector to
your USB 2.0 or later enabled system
• Works with standard and wide screen
monitors
• Resolution (max): 1600 x 1200 @ 32-bit
color depth for standard monitors and
1920 x 1080 @ 32-bit for widescreen monitors
System Requirements
• Desktop or notebook PC with an available
USB 2.0/3.0 port
• Windows®10 (32-/64-bit) / 8 (32-/64-bit) /
7 (32-/64-bit) / Vista (32-/64-bit) / XP SP3
(32-bit)

2
• Mac OS X®10.4 to 10.13.3 (Intel-based Apple
computers only)
Package Contents
•USB 2.0 to VGA Pro
• USB Cable (Type A to B)
• Driver CD and installation guide
Layout
Figure 1: USB 2.0 to VGA Pro Layout
USB port
VGA port
Windows Software Installation
Make sure the proper driver for your graphics
card is installed, the USB 2.0 to VGA Pro is not
designed to work with Windows' Standard VGA
Graphics Adapter driver.
Important: Do not plug the USB 2.0 to VGA Pro
into the computer until instructed to do so.

3
1. Insert the driver CD.
2. A pop-up window AutoPlay will show up.
If not, browse the CD/DVD manually.
3. For Windows 10 / 8/ 7: Run Setup.exe.
For Windows Vista / XP: Choose the folder
according to your OS, and run Setup.exe.
4. Click Yes at the User Account Control
window.
5. DisplayLink Graphics window appears,
and select Install at "system check" stage.
6. At "First connect" stage, connect your
second monitor to the USB 2.0 to VGA Pro
and turn it on.
7. Connect the USB 2.0 to VGA Pro to the
computer by the included USB Cable. When
it is detected, the Final Setup will run
automatically.
8. Once the Final Setup is done, an
"Installation complete" message shows,
at that time select Finish.
9. Restart the computer and the monitor is
ready for use.

4
To Verify Windows Installation
1. Go to Device Manager to verify installation.
For Window 10 / 8 / 7 / XP: Right click This
PC, Computer or My Computer, click
Manage, then click Device Manager.
For Windows Vista: Right click Computer,
click Manage, click Continue, then click
Device Manager.
2. Double click USB Display Adapters, a
VGA Display Adapter should be
displayed.
Uninstalling the Adapter Driver
Windows 10 / 8 / 7
1. Double click Control Panel on desktop,
or click Start, Control Panel.
2. Click Programs, then click Programs and
Features.
3. Select DisplayLink Graphics, then click
Uninstall.
4. Click Yes, Yes, then click OK.
5. Click Yes to complete the uninstallation.

5
Windows Vista
1. Click Start, Control Panel.
2. Click Classic View, double click Programs
and Features.
3. Select DisplayLink Graphics, then click
Uninstall, then click Yes.
4. Click Allow, then click Yes to complete.
Windows XP
1. Click Start, Control Panel.
2. Double click Add/Remove Programs.
3. Select DisplayLink Graphics, click
Remove, then click Yes.
4. Click Yes to complete uninstalling the
driver.
Windows Display Utility
After successful driver installation, a VGA Display
Adapter utility icon will appear in the taskbar.
This display utility allows you to quickly change
the viewing modes and resolutions. Access the
utility by clicking the icon.

6
Viewing Modes
•Screen Resolution: Displays a list of
available resolutions
•Screen Rotation:
Normal - No rotation is applied
Rotated Left - Rotates the extended or
mirrored display by 270 degrees
Rotated Right - Rotates the extended or
mirrored display by 90 degrees
Upside-Down - Rotates the extended or
mirrored display by 180 degrees
•Extend to:
Right - Extends the display to the right of
the main display
Left - Extends the display to the left of the
main display
Above - Extends the display above of the
main display
Below - Extends the display below the
main display

7
• Extend (default): This mode extends your
desktop for easy viewing of multiple
windows. Windows will move off
theprimary display from the right side
and enter the extended display from the
left
•Set as Main Monitor: This mode, makes
the USB 2.0 to VGA Pro the main display
adapter in the system
•Mirror: You will see the same image on
both monitors
•Off: Turns off the connected monitor
•Fit to TV: Adjust the size of the Windows
desktop when the Windows desktop does
not completely appear on the TV
Using Windows Display Properties
(WDP)
Not all the WDP functions are available in
Windows Vista. Instead of using the USB 2.0 to
VGA Display Adapter utility, you can use the
embedded Windows Display Properties (WDP)
to modify settings.

8
WDP allows you to rotate, duplicate or extend
screens as wall as change screen resolution.
Position the mouse cursor anywhere on the
Windows Desktop,
For Windows 10: Right click and select Display
settings
For Windows 8 / Windows 7: Right click and
select Screen Resolution
For Windows XP: Right click then select
Properties.
Properties.
•Display: Use the drop down list to select
a display to be configured
•Resolution: Use the drop down list and
the slider to choose a resolution
•Orientation:
Landscape - Sets the display to landscape
mode
Portrait - Sets the display to portrait mode
Landscape (flipped) - Sets the display to

9
•Multiple displays:
Duplicates these displays - Reproduces the
main display on the second display
Extend these displays - Extends the main
display onto the secondary display
Show Desktop only on 1 - The display
marked 2 becomes blank
Shows Desktop only on 2 - The desktop
appears on the display marked 2. The
display marked 1 becomes blank
•Make this my main display: Check the
box and you will make your USB 2.0 to VGA
Pro the main display adapter in the system.
Make sure the secondary monitor is
selected before choosing this option
• Display Positions: To move the position
of a display, click and hold the display you
wish to move then drag it to the desired
position. The display will be highlighted
with a blue border while you are moving
the display to its new position

10
MAC OS Driver Installation
1. Connect your second monitor to the USB
2.0 to VGA Pro and turn it on, then plug the
USB 2.0 to VGA Pro into the computer.
2. Insert the driver CD, then double click
Driver CD icon on the Desktop.
3. Choose the Mac folder according to your
OS.
4. Double click DisplayLink_Mac_OS....dmg.
5. At the DisplayLink Installer, double click
DisplayLink Software Installer.pkg.
6. At the Introduction, click Continue for
one to two times.
7. At the License, click Continue, and Agree.
8. At the Select Destination, click Continue.
Skip this step if not prompted.
9. At the Installation Type, click Change
Install Location if you want to change
the default saving folder; otherwise, click
Install and Continue Installation.