SIIG DP CyberSerial Dual PCI RJ User manual

1
04-0489A
Introducing the CyberSerial Dual PCI
TheDPCyberSerialDualPCIRJhigh-speedserialI/Ocard
provides two additional 9-pin serial ports.
Features and Benefits
•Conforms to PCI v2.2 Plug and Play
•Full support for Windows-based software
•Reduces CPU load and improves system
performance dramatically
•IRQ sharing feature reduces IRQ conflicts
•High-speed serial port (9-pin) works with 56K V.90
external modems, ISDN terminal adapters, PDAs,
digital cameras, label printers and other serial port
devices
•Built-in FIFO buffers dramatically increase data
transmit/receivespeed,especiallyunderWindows'
multitasking environment
•Works as standard RS232 port or with 5V or 12V
power output for devices that require power from
the serial port
System Requirements
•Pentium® or equivalent computer with an available
PCI slot
•Windows®95 / 98 / 98SE / ME / NT 4.0 / 2000 / XP
(32-/64-bit) / Server 2003 (32-/64-bit) / Vista (32-/
64-bit)
DP CyberSerial Dual PCI RJ
Quick Installation Guide

2
PackageContents
•DP CyberSerial Dual PCI RJ board
• Spare low-profile bracket
• RJ45 to DB9 cable
• Driver CD
• Quick installation guide
Layout
Figure 1. Layout
*If your serial device requires power output from
the serial port, connect the system power source to
board's power connector. However, most serial
devices do not require additional power through
the serial port. Refer to your serial device's manual
for more information.
Jumper Settings (J1, J2)
Short 2-3 = 0 volts
Short 1-2 = 5V
Short 3-4 = 12V
Serial Port 2
Serial Port 1
RJ45 to DB9 cable
Power connector*
J1, J2

3
Hardware Installation
Note: For Low Profile systems, replace the currently
mounted bracket with the included Low Profile bracket.
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord from the back of the
computer.
3. Remove your computer cover. Remove the slot
bracket from an available PCI slot.
4. Set J1 and J2 jumper settings to the desired voltage
only if your serial device needs additional power
from the serial port. However, most serial devices
do not require additional power. For more
information see Jumper Settings on page 2. The
jumpers can be removed if power is not required. If
poweroutputisrequired,connecttheboard'spower
connector.
5. Carefully align the card's bus connector with the
selected PCI slot on the motherboard. Push the
board down firmly, but gently, until it is well seated.
6. Replace the slot bracket holding screw.
7. Replacethecomputercoverandreconnect thepower
cord.

4
Driver Installation
This section provides information on how to install the
DP CyberSerial Dual PCI RJ drivers.
Windows 95
1. At the Update Device Driver Wizard, click Next.
2. Insert the driver CD, and click Other Locations.
Type in D:\9x, click OK, then Finish. (Change D: to
match your CD-ROM drive letter)
3. From the Insert Disk window, click OK. When the
Copying Files dialog box appears, type in
D:\9x, then click OK.
4. Restart Windows to complete the installation.
Windows 98/98SE
1. At the Add New Hardware Wizard, click Next.
2. Select Search for the best driver for your device
(Recommend), then click Next.
3. Insert the driver CD, check Specify a location,
uncheck the other boxes, type in D:\9x, then click
Next. (Change D: to match your CD-ROM drive
letter)
4. Click Next, then Finish.
5. Repeat steps 1-4.
6. Restart Windows to complete the installation.

5
Windows ME
1. At the Add New Hardware Wizard, select Specify
the location of the driver (Advanced),click Next.
2. Insert the driver CD, check Specify a location,
uncheck the other box, type in D:\Me, then click
Next. (Change D: to match your CD-ROM drive
letter)
3. Click Next, then Finish.
4. Repeat steps 1and 2.
5. Click Next, Next, then Finish.
6. Restart Windows to complete the installation.
To Verify Windows 95/98/98SE/ME Installation
1. Fromthemain desktop, double click My Computer,
Control Panel,System,thenclickDeviceManager.
2. Double click Ports (COM & LPT), CyberSerial PCI
16Cxxx... should be displayed two times.
3. Double click Multi-function adapters, SIIG
CyberPro 2S PCI board and PCI Function should
be displayed.
Windows NT 4.0
1. From the desktop click Start, then Run.
2. Insert the driver CD, type in
D:\NT4\install_serial.exe,thenclickOK. (Change
D: to match your CD-ROM drive letter)
3. Click Next when the Welcome window appears.
4. Choose Install, then click Next.
5. Click Yes, then click Exit.
6. Restart Windows to complete the installation.

6
To Verify Windows NT 4.0 Installation
1. Click Start, Settings, Control Panel,double click
Ports device icon.
2. Two new COM ports will be assigned when
successfully installed.
Windows 2000
1. At the Found New Hardware Wizard, click Next.
2. Select Search for a suitable driver for my device
(recommended), and click Next.
3. Check Specify a location, uncheck the other boxes,
and click Next.
4. Insert the driver CD, type in D:\2000, then click OK.
(Change D: to match your CD-ROM drive letter)
5. Click Next and Finish.
6. Repeat steps 1-5 two more times.
7. Restart Windows to complete the installation.
Windows XP/Server 2003 (32-bit)
1. At the Found New Hardware Wizard, insert the
driver CD.
For XP w/SP1 or earlier/ Server 2003: go to step #2.
For XP w/SP2 or later/Server 2003 wSP1 or later:select
No, not this time, click Next.
2. Select Install the software automatically
(Recommended,then click Next.
3. Click Finish.
4. Repeat steps 1-3 two more times.
5. Restart Windows to complete the installation.

7
To Verify Windows 2000/XP/Server 2003
Installation
1. Right click My Computer, click Manage, then select
Device Manager.
2. Click on the +(plus sign) in front of Ports (COM &
LPT), CyberSerial PCI 16Cxxx... should be
displayed two times.
3. Double click Multifunction adapters, SIIG
CyberPro 2S PCI board should be displayed.
Windows XP/Server 2003 (64-bit)
1. At the Found New Hardware Wizard, insert the
driver CD.
For XP w/SP1 or earlier/ Server 2003: go to step #2.
For XP w/SP2 or later/Server 2003 wSP1 or later:select
No, not this time, click Next.
2. Select Install the software automatically
(Recommended,then click Next.
3. Click Continue Anyway, then click Finish.
4. Repeat steps 1-3 several more times.
5. Restart Windows to complete the installation.
Windows Vista™
1. At the Found New Hardware window, insert the
driver CD, click Locate and install driver software
(recommended), then click Continue.
2. Click Next, then click Close.
3. Repeat step #2 to complete the driver installation.
Note: Windows Vista driver installation process
may take several minutes to complete.

8
To Verify Windows Vista Installation
1. Right click Computer,click Manage,clickContinue,
then click Device Manager.
2. Click on the +(plus sign) in front of Ports (COM &
LPT), CyberSerial 16Cxxx... should be displayed
two times.
3. Double click Multifunction adapters, SIIG
CyberPro 2S PCI board should be displayed.
Changing COM Port Address
Some serial devices need a specific COM port in order to
work. If your serial device works properly, do not
change this setting.
Windows 95/98/98SE/ME
1. From the Device Manager window double click
Ports (COM & LPT), then double click the
CyberSerial PCI serial port you want to change.
2. Click Settings tab, click the down arrow that is next
to the Port Name box and select a COM address that
is not currently in use.
3. ClickOK, closeDeviceManagertosavethechanges.
Windows 2000/XP/Server 2003/Vista
1. From the Device Manager window double click
Ports(COM & LPT), then double click the
CyberSerial PCI serial port you want to change.
2. Click Settings tab and click Advanced.
3. Click the down arrow that is next to the COM Port
number box and select a COM port that is not in use.
Click OK.
4. ClickOK, closeDeviceManagertosavethechanges.

9
Blank Page

10
Blank Page