SIIG Cyber 2S1P 950 PCI User manual

1
Cyber 2S1P 950 PCI
Quick Installation Guide
04-0646B
Introducing the Cyber 2S1P 950 PCI
The Cyber 2S1P 950 PCI high-speed serial I/O
card provides two 9-pin serial ports and one
parallel port.
Key Features and Benefits
• Universal PCI card design that works in 32-
/64-bit 3.3V/5V PCI and PCI-X slots
• Provides 2 RS-232 16950 UART serial ports
with built-in 128-byte buffers
• Provides 1 IEEE1284 Compliant SPP/EPP/
ECP parallel port
System Requirements
• Pentium or equivalent computer with an
available PCI slot
• Windows®
8 (32-/64-bit) / 7 (32-/64-bit) /
Vista (32-/64-bit) / XP (32-/64-bit) / Server
2003 & 2008 (32-/64-bit) / Server 2008 R2
/ 2000 / ME / 98SE / 98 / 95

2
Parallel port
Serial port 1
Serial port 2
Power connector
JP1 JP2
Package Contents
•Cyber 2S1P 950 PCI board
• Connector bracket w/9-pin serial port
• Driver CD
• Quick installation guide
Layout
Figure 1: Board Layout
Jumper Settings (JP1, JP2)
Open = 0 volts (default)
Short 1-2 = 5V
Short 2-3 = 12V

3
Note: Mostserialdevicesdonotrequireadditional
power through the serial port. Refer to your
serial device's manual for more information.
Power Connector
Connects to the system's power supply. Make
this connection when the serial port(s) are
configured for 5V or 12V power.
Hardware Installation
General instructions for installing the card are
provided below. Since the design of computer
cases and motherboards vary, refer to your
computer’s reference manual for further
information, if needed.
Static Electricity Discharge may permanently
damage your system. Discharge any static
electricity build up in your body by touching your
computer’s case for a few seconds. Avoid any
contact with internal parts and handle cards
only by their external edges.
1. Turn OFF the power to your computer and
any other connected peripheral devices.

4
2. Unplug the power cord from the computer.
3. Remove the computer cover.
4. Remove the slot bracket from an available
PCI slot.
5. To install the card, carefully align the card's
bus connector with the selected PCI slot on
the motherboard. Push the board down
firmly, but gently, until it is well seated.
6. Replace the slot bracket holding screw to
secure the card.
7. Replace the computer cover and reconnect
the power cord.
Driver Installation
Please make sure the board is installed properly
before proceeding with driver installation.
Windows 8 (32-/64-bit) / Windows 7 (32-/
64-bit) / Server 2008 R2
1. Install the board and boot up Windows.
2. Right click Computer, click Manage, click
Device Manager.

5
3. Insert the driver CD. Close the CD autoplay
window if prompted.
4. Right click PCI Device, click Update Driver
Software.
5. Click Browse my computer for driver
software.
6. Type D:, then click Next. (Change D: to
match your CD/DVD-ROM drive letter)
7. Click Install the driver software anyway.
Skip this step if not prompted.
8. At Windows has successfully updated
your driver software, click Close.
9. Go back to Device Manager, right click PCI
Serial Port, click Update Driver Software.
10. Repeat steps 5-8 to complete the installation.
Windows Vista (32-/64-bit) / Server 2008
(32-/64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click
Locate and install driver software
(recommended), then click Continue.

6
3. Insert the driver CD. Close the CD autoplay
window if prompted.
4. Click Don't search online. (Skip this step if
not prompted)
5. Click I don't have the disc. Show me other
options.
6. Click Browse my computer for driver
software (advanced).
7. Type D:, then click Next. (Change D: to
match your CD/DVD-ROM drive letter)
8. At The sofware for this device has been
successfully installed, click Close. It may
take several minutes for this step to appear.
Do not interrupt the process during this
time.
9. Repeat steps 4-8 to complete the installation.
Windows XP (32-/64-bit) / Server 2003
(32-/64-bit)
1. Install the board and boot up Windows.
2. Insert the driver CD.
3. Select No, not this time, click Next. (Skip
this step if not prompted)

7
4. Select Install the software automatically
(Recommended),then click Next. (Skip this
step if not prompted)
5. Click Finish. It may take several minutes
for this step to appear. Do not interrupt the
process during this time.
6. Repeat steps 3-5 to complete the installation.
Windows 2000
1. At the Found New Hardware Wizard, click
Next.
2. Insert the driver CD.
3. Select Search for a suitable driver for my
device (recommended), and click Next.
4. Select CD-ROM drives, uncheck the other
boxes, and click Next.
5. Click Next and Finish.
6. Repeat steps 1-5 to complete the installation.

8
To Verify Windows 8 / 7 / Vista / XP /
Server 2003 & 2008 / 2008 R2 / 2000
Installation
1. Check in Device Manager to verify
installation.
For Windows 8 / 7 / XP / Server 2003 / 2000:
Right click Computer or My Computer,
click Manage, then click Device Manager.
For Windows Vista: Right click Computer,
click Manage, click Continue, then click
Device Manager.
For Server 2008 & 2008 R2: Right click
Computer, click Manage, double click
Diagnostics, click Device Manager.
2. Click on the +(plus sign) in front of Ports
(COM & LPT), CyberSerial ... 16Cxxx ...
should be displayed.
3. Double click Multifunction adapters, SIIG
CyberPro 2S1P board should be displayed.

9
Windows ME
1. At the Add New Hardware Wizard, choose
Specify the location of the driver
(Advanced), click Next.
2. Check Specify a location, uncheck the other
box, insert the driver CD, type in D:\9x,
then click Next. (Change D: to match your
CD-ROM drive letter)
3. Click Next and Finish.
4. Repeat steps 1-3.
5. Restart Windows to complete the
installation.
Windows 98SE / 98
1. At the Add New Hardware Wizard, click
Next.
2. Select Search for the best driver for your
device (Recommended), then click Next.
3. Select Specify a location, uncheck the other
boxes, insert the driver CD, type in D:\9x,
then click Next. (Change D: to match your
CD-ROM drive letter)
4. Click Next, then Finish.

10
5. Repeat steps 1-4.
6. Restart Windows to complete the
installation.
Windows 95
1. At the Update Device Driver Wizard, click
Next.
2. Insert the driver CD, and click Other
Locations. Type in D:\9x, click OK, then
Finish. (Change D: to match your
CD-ROM drive letter)
3. From the Insert Disk window, click OK.
When the Copying Files dialog box appears,
type in D:\9x, then click OK. (Change D: to
match your CD-ROM drive letter)
4. Repeat steps 1-3.
5. Restart to complete the installation.

11
To Verify Windows ME / 98SE / 98 / 95
Installation
1. From the main desktop, right click My
Computer, click Properties, then click
Device Manager.
2. Double click Ports (COM & LPT),
CyberSerial... 16Cxxx... should be
displayed.
3. Double click Multi-function adapters, SIIG
CyberPro 4S PCI board should be
displayed.
Windows 8 / 7 / Vista / XP / Server 2003 &
2008 / 2008 R2 / 2000
1. From the Device Manager window double
click Ports (COM & LPT), then double click
CyberSerial... port.
2. Click Settings tab and click Advanced.
3. Click the down arrow next to the COM Port
number box, select a COM port that is not
in use. Click OK.
4. Click OK, then close Device Manager to
save the changes.

12
Windows ME / 98SE / 98 / 95
1. From the Device Manager window double
click Ports (COM & LPT), then double click
the CyberSerial PCI serial port.
2. Click Settings tab, click the down arrow
next to Port Name, select a COM address
not currently in use.
3. Click OK, then close Device Manager to
save the changes.
Changing Parallel Port Address (LPT)
Some parallel devices need a specific parallel port
in order to work. If your parallel device works
properly, do not change this setting.
Windows 8 / 7 / Vista / XP / Server 2003 &
2008 / Server 2008 R2 / 2000
1. From the Device Manager window double
click Ports (COM & LPT), then double click
SIIG CyberPro Parallel Port....
2. Click Port Settings tab.

13
3. At the LPT Port Number box, click the
down arrow and select an LPT port that is
not in use.
4. Click OK, then close Device Manager to
save the changes.
Changing COM Port Address
Some serial devices need a specific COM port in
ordertowork. Ifyourserialdeviceworksproperly,
do not change this setting.
Windows ME / 98SE / 98 / 95
1. From the Device Manager window double
click Ports (COM & LPT), then double click
CyberParallel.
2. Click Settings tab, check Enable use of I/O
location 278h.
3. Click OK, click OK again to close Device
Manager, and click Yes to restart Windows
to save the changes.

14
Blank Page

15
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at
www.siig.com and click Support. Our online support database is updated daily with
new drivers and solutions. Answers to your questions could be just a few clicks away.
You can also submit questions online and a technical support analyst will promptly
respond.
SIIG offers a lifetime manufacturer warranty with this product. This warranty covers
the original purchaser and guarantees the product to be free of any defects in materials
or workmanship for the life of the product.
SIIG will, at our discretion, repair or replace (with an identical product or product
having similar features and functionality) the product if defective in materials or
workmanship. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Please see our web site for more warranty details.
If you encounter any problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the product to the store
where you purchased from.
B) If your purchase has passed the store's return policy period, please follow the steps
below to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then REQUEST A PRODUCT REPLACEMENT
to submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request
will be processed, if the product is determined to be defective, an RMA number will
be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All accessories that came with the
original package must be included.
• Clearly write your RMA number on the top of the returned package. SIIG will
refuse to accept any shipping package, and will not be responsible for a product
returned without an RMA number posted on the outside of the shipping
carton.
• You are responsible for the cost of shipping to SIIG. Ship the product to the
following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground in the U.S. and
International Economy outside of the U.S. at no cost to the customer.

PRODUCTNAME
Cyber 2S1P 950 PCI
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG,Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: [phone]
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebooksystemsand external peripherals. SIIG continuestogrow by adding
A/V and Digital Signage connectivity solutions to our extensive portfolio.
SIIGproducts offer comprehensive usermanuals, many user-friendly features,
and are backed by an extensive manufacturer warranty. High quality control
standards are evident by the overall ease of installation and compatibility of
our products, as well as one of the lowest defective return rates in the industry.
SIIG products can be found in computer retail stores, mail order catalogs,
throughmajordistributors, system integrators, and VARsinthe Americas and
the UK, and through e-commerce sites.
Cyber 2S1P 950 PCI is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered
trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft
Corporation. All other names used in this publication are for identification only and may be
trademarks of their respective owners.
December, 2012 Copyright © 2012 by SIIG, Inc. All rights reserved.