SILENT KNIGHT 5207 User manual

Fire Control / Communicator
Rev. C, 04/03
Part Number 150865
SILENT KNIGHT
MODEL 5207
Installation, Programming,
and Operation Manual

150865 i
Contents
Section 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
1.1 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.2 Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Section 2
Agency Listings and Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
2.1 Federal Communications Commission (FCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 Underwriters Laboratories (UL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.2.1 Requirements for All Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.2.2 Requirements for Central Station Fire Alarm Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.2.3 Requirements for Auxiliary Protected Fire Alarm Systems for Fire Alarm Service . . . . . . . . . . . . . 2-3
2.2.4 Requirements for Remote Station Protected Fire Alarm Systems,
for Digital Communication or Polarity Reversal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.3 California Fire Marshal (CFM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.4 Factory Mutual (FM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.5 Materials and Equipment Board of Acceptance Division (MEA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Section 3
Control Panel Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
3.1 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.3 Wiring Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.4 Model 5207 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.5 Current Draw Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.5.1 Worksheet Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.5.2 Worksheet Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.6 Power Supply Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
3.6.1 Connecting the 5198 to AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3.6.2 Connecting the 5198 to Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3.7 Mounting the 5207 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3.8 Terminal Strip Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.9 Telephone Line Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
3.10 Cable Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Section 4
Compatible Product Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
4.1 Class A (Style D) Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.2 Class B (Style A) Zones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4.3 Four-Wire Smoke Detector Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4.4 Two-Wire Smoke Detector Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
4.5 Model 4180 Status Display Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
4.6 Model 5210 Zone Expander Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4.7 Model 5220 Direct Connect Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
4.7.1 City Box Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
4.7.2 NFPA 72 Polarity Reversal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
4.8 Keltron 95M3158 Tones Transmitter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
4.9 Model 5230 Remote Annunciator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
4.9.1 Setting ID Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Model 5207 Fire Control/Communicator Installation and Operation Manual
ii 150865
4.9.2 5230 Permanent Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
4.9.3 Mounting the 5230 Remote Annunciator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
4.9.4 Temporary Annunciator Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
4.10 Model 5395 Signal Power Expander . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
4.11 Model 7181 Zone Converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
4.12 Supervised Notification Appliance Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
4.13 Auxiliary Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Section 5
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
5.1 Built-in Touchpad and Model 5230 Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.1.1 Built-in Touchpad Display Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
5.1.2 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
5.2 System Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
5.2.1 Fire Drills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
5.2.2 Walk Test (Mode 22) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
5.2.3 Automatic Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
5.3 Watchdog Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Section 6
Programming: Quick Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Section 7
Programming: Step-by-Step Complete Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
7.1 Using Step Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1 Programming Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
7.2 Step Programming Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Step 1. Power Up Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Step 2. Device Enables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Step 3. More System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Step 4. Display Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Step 5. Miscellaneous Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
Step 6. Internal Zone Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
Step 7. External Zone Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
Step 8. Number of Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
Step 9. Dialer Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
Step 10. Total Number of Attempts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
Step 11. Number of Events Before Dialer Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
Step 12. Low AC Hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
Step 13. Number of Rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
Step 14. Report to Telephone Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
Step 15. Computer Phone Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
Step 16. Central Station Phone Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
Step 17. Central Station Account Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
Step 18. Dialer Format and Number of Attempts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14
Step 19. Telephone Line to Use for Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14
Step 20. Duration of Delays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15
Step 21. Test Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16
Step 22. Secret Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16
Step 23. Group Relays and Bells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17
Step 24. Alarm Relays and Bells (by Zone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19
Step 25. Zone Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20
Step 26. Zone Location Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21
Steps 27 and 28. Temporal Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22

150865 iii
Section 8
Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1
8.1 Notes for All Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
8.2 SIA Format Printed Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
8.3 FSK & SK 4+2 Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
8.4 16-Zone 4+2 Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
8.5 Radionics BFSK Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
Section 9
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
9.1 Problems With the Model 5198 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
9.1.1 Isolating the Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
9.1.2 Measuring Battery Charging Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
9.2 P3 and P4 Earth Ground Faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
9.3 Accu-ZoneÆ Troubleshooting (Mode 25) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
9.3.1 Mode 25 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
9.4 Troubleshooting and System Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
Appendix A
Compatible Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
A.1 Smoke Detectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Two-Wire Smoke Detectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Four Wire Smoke Detectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
A.2 Notification Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3

Model 5207 Fire Control/Communicator Installation and Operation Manual
iv 150865

150865 1-1
Section 1
Introduction
The Model 5207 is an 8-zone fire alarm control panel (expandable up to 16 zones) with a dig-
ital communicator that meets NFPA 72 requirements. The 5207 cabinet can be surface
mounted or semi-flush mounted.
1.1 About This Manual
The Model 5207 Fire Control/Communicator Installation Manual (P/N 150865) is intended
for those persons involved with the installation and maintenance of the 5207 panel. It is a
comprehensive guide, providing detailed instructions, and should be kept for reference. As
much as possible, we have tried to organize the manual chronologically by the tasks that need
to be performed.
This manual is intended to be used with printed circuit board (PCB), Revision M. If you are
using a different board, contact Silent Knight Security Systems for the appropriate instruc-
tions.
IMPORTANT:
Previous versions of the 5207 were selectable between 12V and 24V. This release is 24V only.
*All information regarding 12V have been removed from this manual.
Some versions of the 5207 product documentation were made up of two manuals, one for
hardware installation and one for programming. We have combined both manuals into one.
With the exception of information about the obsolete 5521 programmer*, this manual contains
all information previously contained in the two manuals.
*Contact Silent Knight if you need this information.
A clear rectangle represents a key that you press on a
touchpad.
LCD DISPLAY
MESSAGE The font shown to the left represents messages that you see on a liquid crystal display (LCD) or the seven-seg-
ment (built-in touchpad) display.
1-1, 2-3, etc. This manual is organized into sections. Section numbers
are part of the page numbers. For example, 1-1 means
Page 1 of Section 1.
KEY

Model 5207 Fire Control/Communicator Installation and Operation Manual
1-2 150865
1.2 Optional Accessories
Table 1-1: Compatible Modules
Manufactured by Silent Knight
Model What It Does
4180 Status Display/Relay
Module
For remote annunciation of alarm and trouble
status information for each zone.
5210 Zone Expander Adds 8 zones to the 5207 for a total expansion of
the system to 16 zones.
5220 Direct Connect Module For direct alarming and trouble transmission from
the 5207 to a supervising station.
5230 Remote Annunciator For remote annunciation, operation, and on-site
programming.
Quick connect program cable,
part number 130294
For temporarily connecting the 5230 to the 5207
for programming.
5395 Signal Power Expander Notification circuit power for additional
notification appliances. Provides additional 6A of
24 VDC, supervised.
5541 Downloading Software For remote programming of the 5207 using a
personal computer.
5530 Modem Modem for downloading; required if the 5541
software is used.
7181 Zone Converter Converts a zone from class B to class A or from
class A to class B. One 7181 per zone to be
converted.

150865 2-1
Section 2
Agency Listings and Requirements
2.1 Federal Communications Commission (FCC)
1. If requested by the telephone company, the following information must be provided before the
5207 can be connected to the phone lines:
2. This device may not be directly connected to coin telephone or party line services.
3. This device cannot be adjusted or repaired in the field. In case of trouble with the device, notify
the installing company or return to:
Silent Knight Security Systems
7550 Meridian Circle
Maple Grove, MN 55369-4927
612-493-6455
800-328-0103
4. If the 5207 causes harm to the telephone network, the telephone company will notify the user in
advance that temporary discontinuance of service may be required. When advance notice is not
practical, the telephone company will notify the user as soon as possible. Users have the right to
file complaints, if necessary, with the Federal Communications Commission.
5. The telephone company may make changes in its facilities, equipment, operations, or procedures
that could affect the operation of the equipment. If this happens, the telephone company will pro-
vide advance notice to allow you to make the necessary modifications to maintain uninterrupted
service.
A. Manufacturer: Silent Knight Security Systems
B. Model Number: 5207
C. FCC registration number: AC6USA-65475-AL-E
Ringer equivalence: 0.9B
D. Type of jack (to be installed by the telephone
company): RJ31X
Warning
This device has been verified to comply with FCC Rules Part 15. Operation is subject to the
two following conditions: (1) This device may not cause radio interference; and (2) This device
must accept any interference received including interference that may cause undesired
operation.

Model 5207 Fire Control/Communicator Installation and Operation Manual
2-2 150865
2.2 Underwriters Laboratories (UL)
The 5207 is UL Listed as a control unit for use in Central Station Fire-Protective Signaling
systems. If the 5207 and its accessories are to be used as part of a UL installation, carefully
read the UL requirements in this section. The following applicable NFPA 72 standards can be
found in more detail in the NFPA 72 National Fire Alarm Code, 1993 Edition:
Chapter 3
ï Local Protected Fire Alarm Systems, Chapter 4
Chapter 4
ï Central Station Fire Alarm Systems
ï Auxiliary Protected Fire Alarm Systems for Fire Alarm Service (City Box)
ï Remote Station Protected Fire Alarm Systems (Polarity Reversal)
ï Proprietary Fire Alarm Systems
2.2.1 Requirements for All Installations
General requirements are described below. The sections that follow describe additional
requirements for the type of installation (for example, Central Station Fire Alarm systems,
Local Protected Fire Alarm systems, and so on).
1. All field wiring must be 18-gauge or larger (for example, 16, 14, and so on).
2. Use UL listed smoke detectors compatible with the 5207. Refer to Appendix A.
3. Use UL listed compatible notification devices. Refer to Appendix A.
4. All notification devices must be UL listed.
2.2.2 Requirements for Central Station Fire Alarm Systems
1. The Ground Fault Detection option must be selected (programming Step 5).
2. The Phone Line #2 Enable option must be selected (programming Step 9).
3. The Phone Line Monitor Enable option must be selected (programming Step 9).
4. Set the Total Attempts option for between 5-10 attempts (programming Step 10).
5. Do not select the Ground Start Option (programming Step 9).
6. Enable the automatic daily test by selecting a phone number for the Report Test to Phone
#1-4 option (programming Step 14.4).
7. On class A (style D) zones, the number of waterflow devices is limited to five.
8. Auxiliary relays may not be programmed to activate for Pre-Alarm. See Section 4.13.

Agency Listings and Requirements
150865 2-3
2.2.3 Requirements for Auxiliary Protected Fire Alarm Systems for
Fire Alarm Service
1. Follow the current load restrictions shown in Section 3.5.
2. The Model 5220 Direct Connect module must be installed (see Section 4.7 for wiring).
2.2.4 Requirements for Remote Station Protected Fire Alarm
Systems, for Digital Communication or Polarity Reversal
1. Follow the current load restrictions shown in Section 3.5.
2. Use the 5207ís built-in dialer or install the Model 5220 Direct Connect Module (see
Section 4.7).
2.3 California Fire Marshal (CFM)
The CFM approval number for the 5207 is 7165-0559:111.
2.4 Factory Mutual (FM)
The Model 5207 is FM approved under project # OQ1A3.AY when used with the Silent
Knight Model 9000 Receiver.
2.5 Materials and Equipment Board of Acceptance
Division (MEA)
The 5207 is approved under MEA. Approval was previously given from the City of New
York Board of Standards and Appeals (BSA), the 5207 is still approved under BSA Calendar
Number 703-88-SA.

Model 5207 Fire Control/Communicator Installation and Operation Manual
2-4 150865

150865 3-1
Section 3
Control Panel Installation
3.1 Electrical Specifications
3.2 Environmental Specifications
It is important to protect the 5207 control panel from water. To prevent water damage, the fol-
lowing conditions should be AVOIDED when mounting the units:
ï Do not mount directly on exterior walls, especially masonry walls (condensation).
ï Do not mount directly on exterior walls below grade (condensation).
ï Protect from plumbing leaks.
ï Protect from splash caused by sprinkler system inspection ports.
ï Do not mount in areas with humidity-generating equipment (such as dryers, production
machinery).
When selecting a location to mount the 5207 control panel, the unit should be mounted where
it will NOT be exposed to temperatures outside the range of 0∞C-49∞C (32∞F-120∞F) or
humidity outside the range of 10%-85% at 30∞C (86∞F) noncondensing.
See also the mounting recommendations in 3.7 for additional environmental specifications.
Table 3-1 Electrical Specifications
Primary AC 120 Vrms at 60 Hz, 2A
Total DC Load 5A
Accessory Power 18.4 V to 27.6 V max., 1A
Smoke Power 18.4 V to 27.6 V max., 1A
Battery Charging Voltage 27.3
Battery Charging Current 2.62 A max.
Class B (style A) Circuit Current 60 mA max.
Telephone Minimum Input Sensitivity 45 dB
Good Phone Line Voltage 3 V
Maximum Low Battery Detect 20.4
Minimum Low AC Detect 98
Maximum Watchdog Response Time 4 sec.
Notification Power 1A max. per output (4A total)

Model 5207 Fire Control/Communicator Installation and Operation Manual
3-2 150865
3.3 Wiring Specifications
To avoid induced noise (transfer of electrical energy from one wire to another), keep input
wiring isolated from high current output and power wiring. Induced noise can interfere with
telephone communication or even cause false alarms. Avoid pulling one multiconductor cable
for the entire panel. Instead, separate the wiring as follows:
DO NOT pull wires from different groups through the same conduit. If you must run them
together, do so for as short a distance as possible or use shielded cable. Connect the shield to
earth ground at the panel only.
For the same reasons, wiring within the cabinet should be routed around the perimeter of the
cabinet. It should not cross the printed circuit board where it could induce noise into the sen-
sitive microelectronics or pick up unwanted RF noise from the high speed circuits.
High frequency noise, such as that produced by the inductive reactance of a speaker or bell,
can also be reduced by running the wire through ferrite shield beads or by wrapping it around
a ferrite toroid. Figure 3-1 provides an example.
Figure 3-1 Wire Routing Example
1/4" spacing must be maintained Input/Output Type Wiring
between each of these circuit types; High current: AC power, speaker, and notification devices
as well as between power limited Low current: Annunciator and zone loop wiring
and non-power limited circuits. Audio: Telephone wiring

Control Panel Installation
150865 3-3
3.4 Model 5207 Wiring Diagram
Figure 3-2 is a wiring diagram for wiring the Model 5207 panel.
Figure 3-2 Model 5207 Wiring Reference

Model 5207 Fire Control/Communicator Installation and Operation Manual
3-4 150865
3.5 Current Draw Worksheet
Table 3-2 Current Draw Worksheet
Device Number of
Devices Current per Device Standby
Current
Alarm
Current
For each device, use this formula: This column X This column = Current per number of devices.
5207 Control Panel 1 Standby: 120 mA 120 mA
Alarm: 700 mA
(worst case)
700 mA
5210 Zone Expander 1 Standby: 40 mA mA
Alarm: 40 mA mA
5220 Direct Connect 1 Standby: 50 mA mA
Alarm: 50 mA mA
5230 Annunciator Standby: 60 mA mA
(7 max.) Alarm: 120 mA mA
4180 Status Display Standby: 20 mA mA
(2 max.) Alarm: 140 mA mA
A Current Subtotals: mA mA
Smoke Detectors Refer to device manual for current ratings. See Appendix A for compatible devices.
Standby: mA mA
Alarm: mA mA
Standby: mA mA
Alarm: mA mA
Standby: mA
Alarm: mA mA
B Current Subtotal: mA mA
Notification Appliances Refer to device manual for current ratings. See Appendix A for compatible devices.
mA
mA
mA
mA
C Current Subtotal: mA
Additional Devices
Standby: mA mA
Alarm: mA mA
Standby: mA mA
Alarm: mA mA
Standby: mA mA
Alarm: mA mA
D Current Subtotal: mA mA
Total current ratings of all devices in system (add A-D): mA mA
ETotal current ratings converted to amperes (x .001): A A
Note: Use this information in conjunction with Table 3-3 and Table 3-4 to complete battery calculations.

Control Panel Installation
150865 3-5
3.5.1 Worksheet Example
The Current Draw worksheet is included to help you calculate the amount of current the sys-
tem draws on standby and in an alarm condition. Refer to Table 3-4 for available battery sizes
and the maximum standby current load each can support.
Figure 3-3 is an example of a completed worksheet.
Figure 3-3 Current Draw Worksheet Example

Model 5207 Fire Control/Communicator Installation and Operation Manual
3-6 150865
3.5.2 Worksheet Requirements
The following steps must be taken when determining Model 5207 current ratings:
1. Measure the alarm current. If only one current rating is listed, the draw for that device is
the same whether the system is in alarm or standby condition. The exception is for notifi-
cation devices, which are rated at alarm current only. Standby current for notification
devices is 0 mA.
2. To detect the actual maximum alarm current, measure the current draw (with no devices
connected to the panel) by connecting a DC amp meter in series with one of the batteries.
Disconnect the AC power source. Put the panel in alarm. The meter will indicate the
alarm current, which will be in the range of 120-700 mA. Fill in the system alarm current
in the Current per Device column of the Current Draw worksheet. You can estimate with-
out measuring the alarm current by filling in the maximum total alarm current of 700 mA.
3. For smoke detectors, notification devices, and devices not mentioned in the manual, refer
to the device manual for the current ratings. The worksheet example shown on the previ-
ous page provides rough estimates for a ì worst caseî installation.
4. Use Table 3-3 to calculate the correct battery AH rating needed for your installation. See
also the example (Figure 3-4) on the next page. Note that the calculated rating in Row H
cannot exceed the ratings shown in Table 3-4.
Table 3-3 Battery Calculations
Total Standby Current Total Alarm Current
A Total supervisory current from the Current Draw
Worksheet (row E).
A
B Number of standby hours (24 and 60 for NFPA 72,
Chapter 1, 1-5.2.5).
H
C Multiply Lines A and B. AH
D Total alarm current from the Current Draw worksheet
(row E).
A
E Alarm sounding period in hours. (For example, 5
minutes = .084 hours.)
H
F Multiply lines D and E. AH
G Add lines C and F. AH
H Multiply line G by 1.2.
(Total ampere/hours required*)
AH
*Use next size battery with capacity greater than required.

Control Panel Installation
150865 3-7
Figure 3-4 Battery Calculation Example
5. Refer to to verify the battery size you need to provide at least the total standby current you
have calculated. If the installation must meet requirements for NFPA 72 (Auxiliary Pro-
tected Fire Alarm Systems for Fire Alarm Service or Remote Station Protected Fire Alarm
Systems, Digital Communication or Polarity Reversal), the total standby current cannot
exceed the amount shown in the last column of the following table:
Table 3-4 Maximum Battery Standby Load
6. Ensure that the total current of all items attached to the 5207, including the 5207 itself,
does not exceed 5 A when the panel is in alarm (see Section 3.1).
Rechargeable
Battery Size
Max. Load for 24 hrs.
Standby, 5 mins. Alarm
*Max. Load for 60 hrs.
Standby, 5 mins. Alarm
17 AH 435 mA 175 mA
34 AH (if wired in parallel)
(Largest size battery that can
be used.)
873 mA 350 mA
* Required for NFPA 72 Auxiliary Protected Fire Alarm Systems for Fire Service (City Box) and
Remote Station Protected Fire Alarm Systems (Polarity Reversal).

Model 5207 Fire Control/Communicator Installation and Operation Manual
3-8 150865
3.6 Power Supply Wiring
The Model 5198 power supply delivers 24 VDC at 5A for loop power, smoke detector power,
notification device power, and accessory power. The Model 6914 is a 12-Volt, 17-AH battery.
Figure 3-5 shows the power supply wiring.
Figure 3-5 Power Supply Wiring
Note: All conduit and wiring connected to the 5207 must meet the applicable National Electric Code, NFPA Stan-
dards, state, and local building code requirements. In all cases, the authority having jurisdiction takes pre-
cedence.
Warning
To reduce the risk of electrical shock, make sure that all power has been turned off or disconnected before attempting
to connect the Model 5198 power supply. Do NOT apply power to this panel until all accessories are properly
connected.

Control Panel Installation
150865 3-9
3.6.1 Connecting the 5198 to AC Power
The Model 5198 is mounted behind the power shield.
ï Connect the black wire from the 120 VAC 60 Hz source to terminal 1 on the 5198.
ï Connect the white (neutral) wire from the 120 VAC 60 Hz AC source to terminal 3 on the
5198.
ï Connect the ground wire from the 120 VAC 60 Hz source to terminal 2 on the 5198.
3.6.2 Connecting the 5198 to Batteries
The tables in Section 4 will help you determine correct battery size.
When using two batteries, it is recommended that they be of the same ampere hour (AH) rat-
ing.
The Model 5198 provides two sets of battery leads to connect two 12 VDC batteries in series.
1. Connect the first red battery lead to the positive side of battery #1.
2. Connect the first black battery lead to the negative side of battery #1.
3. Connect the second red battery lead to the positive side of battery #2.
4. Connect the second black battery lead to the negative side of battery #2.
Note: The total current draw on loop power, accessory power, and notification device outputs
must not exceed 6A.
3.7 Mounting the 5207
Read the environmental specifications in 3.2 before mounting the 5207 panel.
The 5207 cabinet outside dimensions are: 26.4" H x 16" W x 4" D (67.1 x 40.64 x 10.16 cm).
Flush Mounting Dimensions are: 25" H x 14-1/2" W x 3-3/8" D (63.5 x 36.83 x 8.57 cm)
DO NOT flush-mount the 5207 cabinet in a wall designated as a fire break.
The 5207 panel should be located within a secured area, where it is accessible to main drop
wiring runs and where it can be easily tested and serviced. End-users responsible for main-
taining the panel should be able to hear alarms and troubles. When selecting a location, keep
in mind that the panel itself is the main source of alarm and trouble annunciation.
When mounting on interior walls, use appropriate screw anchors in plaster. When mounting
on concrete, especially when moisture is expected, attach a piece of 3/4 inch plywood to the
concrete surface and then attach the 5207 to the plywood. Also mount any other desired com-
ponents to the plywood.
Caution
Apply AC power before connecting the batteries to the power supply to prevent arcing on battery terminals.