Silicon Laboratories CP2102N-MINIEK User manual

UG254: CP2102N-MINIEK Kit User's Guide
The CP2102N-MINIEK kit is designed to showcase the various
features of the CP2102N USBXpress® devices.
These highly-integrated USB-to-UART bridge controllers provide a simple solution for
updating RS-232 designs to USB using a minimum of components and PCB space. By
eliminating the need for complex firmware and driver development, the CP2102N devi-
ces enable quick USB connectivity with minimal development effort.
The kit includes the following:
• CP2102N USB-to-UART Bridge Mini Evaluation Board
• Getting Started card
KEY FEATURES
• CP2102N USB-to-UART Bridge
• Headers for easy access to UART, GPIO,
and Battery Charger Detect pins
• 0.1" header pitch for breadboard
compatibility
• Small board size
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1

1. Getting Started
1. Download and Install the Latest Virtual COM Port (VCP) Drivers.
The Virtual COM Port (VCP) drivers enable the CP2102N to appear as a standard COM port. Download the latest version of driv-
ers from the Silicon Labs website:
http://www.silabs.com/vcpdrivers
In most cases, select the default option without serial enumeration.
2. Set Up Your Kit.
a. Provide power to the board by connecting the mini USB connector to the PC using a mini USB cable (not provided). When a
connection has been established successfully, the LED (marked in the picture) lights up.
LED
3. Detect Your Device.
The CP2102N device will appear as a COM port in Device Manager in Windows. As a virtual COM port, the CP210x functions
identically to a real COM port from the reference point of both the host application and the serial device, and it can support serial
device control requests defined in the Microsoft Win32® Communications API.
UG254: CP2102N-MINIEK Kit User's Guide
Getting Started
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 1

4. Set up a Loop-Back Test.
Short the CP210x RXD and TXD pins on header J2.
5. Send and Receive Some Data.
UG254: CP2102N-MINIEK Kit User's Guide
Getting Started
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 2

a. In Windows, open a serial terminal program (downloaded separately, RealTerm pictured) to verify the CP2102N UART func-
tionality.
b. Set the baud rate and select the COM port from Device Manager.
c. Type in the transmit area. The characters should echo back after looping through the CP2102N TXD and RXD pins.
6. Utilize the Available Resources.
The next section includes additional resources available for the device, including documentation and application notes.
UG254: CP2102N-MINIEK Kit User's Guide
Getting Started
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 3

2. Relevant Documentation
The following Application Notes are applicable to CP2102N devices:
•AN721: CP210x Device Customization Guide — This application note guides developers through the configuration process of
USBXpress devices using Simplicity Studio [Xpress Configurator].
•AN220: USB Driver Customization — This document and accompanying software enable the customization of the CP210x Virtual
COM Port (VCP) and USBXpress drivers.
•AN197: Serial Communications Guide for CP210x — This document describes recommendations for communicating with USBX-
press CP210x devices using the Virtual COM Port (VCP) driver.
•AN976: Migrating from a CP2102 to a CP2102N — This document guides developers on how to migrate existing systems using the
CP2102 to the CP2102N.
•AN169: USBXpress Programmer’s Guide — This application note provides recommendations and examples for developing using
the USBXpress direct-access driver.
•AN807: Recertifying a Customized Windows HCK Driver Package — This document describes the WHQL certification process re-
quired for customized drivers.
•AN223: Runtime GPIO Control for CP210x — This document describes how to toggle GPIO pins from the USB host.
Application Notes can be accessed on the Silicon Labs website (www.silabs.com/interface-appnotes) or in Simplicity Studio using the
[Getting Started]>[Application Notes] area of the launcher.
UG254: CP2102N-MINIEK Kit User's Guide
Relevant Documentation
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 4

3. Device Customization
Device customization for the CP2102N is done through Xpress Configurator, which is available in Simplicity Studio:
http://www.silabs.com/simplicity
The Simplicity Studio software package contains all the tools, drivers, configuration software, and documentation needed to use the
CP2102N USB-to-UART Bridge Mini Evaluation Board.
After downloading the latest version of Simplicity Studio and installing the software:
1. Install the CP210x Virtual COM Port Driver during the software setup steps, if it's not already installed. This action can always be
accessed through [Help]>[Setup Tasks].
2. Connect the CP2102N to the PC.
3. Select [CP2102N] under [Devices]. On the board, a successful USB connection is established when the SUSPENDB LED (D2)
turns on.
4. Click on [Compatible Tools]>[Xpress Configurator] to open Xpress Configurator and customize the device.
Documentation for each of the customization options is provided within Xpress Configurator. More information on each of these options
can be found in AN721: CP210x Device Customization Guide, which is available on the Silicon Labs website (www.silabs.com/inter-
face-appnotes) or within Simplicity Studio under [Getting Started]>[Application Notes].
UG254: CP2102N-MINIEK Kit User's Guide
Device Customization
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 5

4. Driver Options and Software Interface
4.1 Virtual COM Port (VCP) Driver
CP2102N devices are pre-programmed with a VID of 0x10C4 and PID of 0xEA60. This VID and PID combination matches the Virtual
COM Port (VCP) driver. With this driver, the CP2102N will appear as a COM port and can be accessed using any terminal program or
custom-written software. Install the VCP driver as part of the Simplicity Studio installation or download it directly from the Silicon Labs
website (www.silabs.com/interface-software).
If the Virtual COM Port (VCP) drivers are used, the CP2102N will appear as a COM port in the Device Manager, as shown in the figure
below. The CP2102N will always use the lowest available COM port for operation. For instance, if COM ports 1 and 2 are in use by
other peripherals and applications, the CP2102N will use COM 3.
The CP2102N functions identically to a COM port from the reference point of both the host application and the serial device, and it can
support serial device control requests defined in the Microsoft Win32® Communications API. Examples for how to communicate with
the device as a serial COM port are included in AN197: Serial Communications Guide for CP210x or in the SDK.
Figure 4.1. CP2102N in Device Manager — VCP
UG254: CP2102N-MINIEK Kit User's Guide
Driver Options and Software Interface
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 6

4.2 USBXpress Driver
An alternative driver is the USBXpress® direct-access driver, which is also available on the Silicon Labs website (www.silabs.com/inter-
face-software). Rather than appearing as a COM port, software can use a simple, high-level Application Program Interface (API) to pro-
vide access to CP2102N for complete USB connectivity. No USB protocol or host device driver expertise is required. The USBXpress
Development Kit includes Windows device drivers, Windows device driver installer, and host interface function library (host API) provi-
ded in the form of a Windows Dynamic Link Library (DLL). See Application Note AN169: USBXpress Programmer’s Guide for detailed
information on using the USBXpress drivers.
If the USBXpress drivers are used, the CP2102N will appear as a USB USBXpress device as shown in the figure below. Examples for
how to communicate with the device using the USBXpress interface are included in AN169: USBXpress Programmer’s Guide.
Figure 4.2. CP2102N in Device Manager — USBXpress
UG254: CP2102N-MINIEK Kit User's Guide
Driver Options and Software Interface
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 7

5. Hardware Overview
The CP2102N Mini Evaluation Kit includes an evaluation board with a CP2102N device pre-installed for evaluation and preliminary soft-
ware development. Numerous input/output (I/O) connections are provided to facilitate prototyping using the evaluation board. Refer to
the figure below for the locations of the various I/O connectors.
Table 5.1. CP2102N Mini Evaluation Board Component Overview
Component Description
D2 SUSPENDb indicator LED
J1 USB mini connector
J2 Header for UART pins (TX, RX, RTS, CTS), VBUS pin, suspend
pins, and Charge Enable pin CHR0
J5 Header for power pins (VDD, VREGIN), reset pin, GPIOs, and
Charge Enable pins (CHREN, CHR1)
J5
GND
TXD
RXD
CTS
VBUS
SUSPENDb
SUSPEND
RTS
GND
CHR0
J2
VDD
VDD
VREGIN
GPIO.0
GPIO.1
GPIO.2
GPIO.3
RSTb
CHREN
CHR1
Figure 5.1. CP2102N Mini Evaluation Board
UG254: CP2102N-MINIEK Kit User's Guide
Hardware Overview
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 8

5.1 USB Interface (J1)
A Universal Serial Bus (USB) mini connector (J1) is provided to facilitate connections to the USB interface on the CP2102N. See the
table below for the USB pin definitions.
Table 5.2. USB Mini Connector Pin Descriptions
Pin Number Description
1 VBUS
2 D-
3 D+
4 ID (Not Connected)
5 Ground
UG254: CP2102N-MINIEK Kit User's Guide
Hardware Overview
silabs.com | Smart. Connected. Energy-friendly. Rev. 0.1 | 9