Silvercrest SV 125 C3 User manual

IAN 400318_2107
VACUUM SEALER / VAKUUMIERER
APPAREIL DE MISE SOUS VIDE SV 125 C3
APPAREIL DE MISE SOUS VIDE
Guide abrégé
VACUUM SEALER
Short manual
VACUMEERMACHINE
Beknopte gebruiksaanwijzing
VAKUOVAČKA
Stručný návod
VAKUUMPAKKER
Kvikvejledning
VÁKUOVAČ
Krátky návod
VÁKUUMOS FÓLIAHEGESZTŐ
Rövid útmutató
VAKUUMIERER
Kurzanleitung
PAKOWARKA PRÓŻNIOWA
Skrócona instrukcja obsługi
ENVASADORA AL VACÍO
Guía breve
APARAT ZA VAKUUMIRANJE
Kratka navodila
MACCHINA SIGILLASACCHETTI
Istruzioni brevi
SHORT MANUAL
KURZANLEITUNG
GUIDE ABRÉGÉ

GB / IE Short manual Page 1
DE / AT / CH Kurzanleitung Seite 21
FR / BE Guide abrégé Page 43
NL / BE Beknopte gebruiksaanwijzing Pagina 63
CZ Stručný návod Strana 83
PL Skrócona instrukcja obsługi Strona 103
SK Krátky návod Strana 123
ES Guía breve Página 143
DK Kvikvejledning Side 163
IT Istruzioni brevi Pagina 183
HU Rövid útmutató Oldal 203
SI Kratka navodila Stran 223
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit
allen Funktionen des Gerätes vertraut.
Avant de lire le mode d‘emploi, ouvrez la page contenant les illustrations et familiarisez-vous ensuite avec
toutes les fonctions de l‘appareil.
Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle functies van het
apparaat.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi
funkcjami urządzenia.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Antes de empezar a leer abra la página que contiene las imágenes y, en seguida, familiarícese con todas
las funciones del dispositivo.
Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.
Prima di leggere aprire la pagina con le immagini e prendere confidenza con le diverse funzioni
dell'apparecchio.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik funkcióját.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Soft
A
B
1
2
3
4
7
5
0
8
6
r
ew
q
t z
9
C
u
i o p
2x

GB│IE │ 1 ■
SV 125 C3
Contents
Information about this short manual ..............................2
Copyright............................................................... 2
Limitation of liability....................................................... 2
Intended use ..................................................2
Package contents and transport inspection .........................3
Unpacking .............................................................. 3
Disposal of packaging materials ............................................. 3
Description of the appliance .....................................4
Technical data .................................................5
Safety guidelines ..............................................5
Setting up and connecting .......................................7
Set-up location requirements ................................................ 7
Electrical connection ...................................................... 7
Functions .....................................................8
Tips ..........................................................8
Welding a tube film............................................10
Vacuum sealing...............................................13
Vacuuming the tube film...................................................13
Vacuuming containers and resealable bags ................................... 15
Cleaning.....................................................17
Cleaning the appliance ...................................................17
Storage .....................................................18
Disposal .....................................................18
Service ......................................................19
Importer.....................................................19
Ordering replacement parts ....................................20
IB_400318_SV125C3_LB8_short.indb 1 27.09.2021 14:42:40

■ 2 │ GB│IE SV 125 C3
Information about this short manual
This document is a shortened print version of the complete operating instructions.
Scanning the QR code will take you directly to the Lidl Service
page (www.lidl-service.com), where you can view and
download the full version of the operating instructions by entering
the article number (IAN) 400318_2107.
WARNING!
Observe the information in the complete operating instructions and the safety
instructions to avoid personal injury and damage to property.
The short manual is an integral part of this product. Before using the product,
please familiarise yourself with all operating and safety instructions. Keep the
short manual in a safe place and hand over all documents when passing the
product on to any future owner/user.
Copyright
This documentation is protected by copyright.
Any reproduction, or any reprint even in the form of excerpts, as well as the rendi-
tion of figures even in modified form, is only permitted with the manufacturer’s
written consent.
Limitation of liability
All the technical information, data and instructions regarding installation, connec-
tion and operation contained in these operating instructions corresponds to the
latest information available to us at the time of printing and takes our previous
experience and know-how into account.
No claims can be derived from the details, illustrations and descriptions in these
instructions.
The manufacturer assumes no responsibility for damage caused by failure to
observe these instructions, improper use, incompetent repairs, unauthorised
modifications or for the use of non-approved replacement parts.
Intended use
This appliance is intended exclusively for the sealing and vacuum-packing of
foodstuffs in household quantities and only in private households. This device is
not intended for commercial or industrial applications or for continuous use.
It is not intended for any other use or use beyond that specified. Claims of any
kind for damage arising as a result of incorrect use will not be accepted.
The risk shall be borne solely by the user.
IB_400318_SV125C3_LB8_short.indb 2 27.09.2021 14:42:43

GB│IE │ 3 ■
SV 125 C3
Package contents and transport inspection
The appliance is supplied with the following components as standard:
▯ Vacuum sealer
▯ 1 x film roll
▯ 2 x tubes
▯ 3 x adapters
▯ 1 x replacement sealing ring
▯ These short manual
NOTE
► Check the package for completeness and for signs of visible damage.
► If the consignment is incomplete or damaged due to defective packaging
or carriage, contact the Service hotline (see the chapter Service).
Unpacking
♦ Remove all parts of the appliance, the tube film and the short manual from
the carton.
♦ Remove all packaging material.
♦ Remove the protective film from the control panel.
DANGER
► Packaging materials should not be used as a plaything. Risk of suffocation.
Disposal of packaging materials
The packaging protects the appliance from damage during carriage.
The packaging materials have been selected for their environmental friendliness
and ease of disposal, and are therefore recyclable.
Returning the packaging to the materials cycle conserves raw materials and
reduces the amount of waste that is generated. Dispose of packaging materials
that are no longer needed in accordance with applicable local regulations.
Dispose of the packaging in an environmentally friendly manner.
Note the labelling on the packaging and separate the packaging material
components for disposal if necessary. The packaging material is labelled with
abbreviations (a) and numbers (b) with the following meanings: 1–7: plastics,
20–22: paper and cardboard, 80–98: composites
NOTE
► If possible, keep the original packaging during the warranty period so that the
device can be properly packed for returning in the event of a warranty claim.
IB_400318_SV125C3_LB8_short.indb 3 27.09.2021 14:42:46

■ 4 │ GB│IE SV 125 C3
Description of the appliance
Figure A
1Appliance lid
2Suction tube
3Cable retainer
4Welding wires
5Lower sealing ring
6Rear limiters
7Front limiters
8Lid release
9Suction fitting
0Upper sealing ring
qPress seal
Figure B
wbutton (start/cancel “sealing” function) with control lamp (red)
ebutton (start/cancel “vacuuming and sealing” function) with control lamp (red)
rbutton (activate/deactivate additional function “wet”) with control lamp
(green)
tbutton (activate/deactivate additional function “soft”) with control lamp (green)
zbutton (start/cancel “external vacuuming” function) with control lamp (green)
Figure C
uVacuum hose
iAdapter A
oAdapter B
pAdapter C
IB_400318_SV125C3_LB8_short.indb 4 27.09.2021 14:42:46

GB│IE │ 5 ■
SV 125 C3
Technical data
Operating voltage 220- 240 V ∼ (alternating current), 50/60 Hz
Power consumption 125W
Protection class II/ (double insulation)
All of the parts of this appliance that come into
contact with food are food-safe.
Safety guidelines
RISK OF ELECTRIC SHOCK
■ Prior to use, check the device for visible external damage.
Never operate an appliance that is damaged.
■ To avoid potential risks, if the appliance power cable is
damaged, it must be replaced by the manufacturer, its
customer service or by a qualified technician.
■ NEVER use the appliance with a defective power cable.
■ Do not use extension cables or power socket strips that do
not meet the required safety standards.
■ Never open the appliance housing!
■ Remove the plug from the mains power socket before be-
ginning to clean the device.
■ Ensure that no moisture can penetrate the device during
cleaning.
RISK OF INJURY!
■ All repairs must be carried out by authorised special-
ist companies or by the Customer Service department.
Improper repairs may result in a risk of injury to the user
or damage to the appliance. They will also invalidate any
warranty claim.
IB_400318_SV125C3_LB8_short.indb 5 27.09.2021 14:42:49

■ 6 │ GB│IE SV 125 C3
RISK OF INJURY!
■ The mains power socket must be easily accessible, so that
the power cable can be easily disconnected in the event
of an emergency.
■ Cleaning and user maintenance tasks may not be carried
out by children unless they are supervised.
■ The appliance and its connecting cable must be kept
away from children younger than 8 years old.
■ This appliance may be used by children aged 8 years
and above and by persons with limited physical, sensory
or mental capabilities or lack of experience and knowl-
edge, provided that they are under supervision or have
been told how to use the appliance safely and are aware
of the potential risks.
■ Children must not play with the appliance!
■ Children should be supervised to ensure that they do not
play with the appliance.
■ Do not leave the appliance unsupervised when it is ready
for use. To prevent it being switched on accidentally, al-
ways unplug the appliance after use or during breaks.
CAUTION – PROPERTY DAMAGE!
■ Do not use an external timer switch or a separate remote
control system to operate the appliance.
NOTE
► No user action is required to switch the product between
50 and 60 Hz. The product adapts automatically to either
50 or 60 Hz.
IB_400318_SV125C3_LB8_short.indb 6 27.09.2021 14:42:49

GB│IE │ 7 ■
SV 125 C3
Setting up and connecting
Set-up location requirements
For safe and trouble-free operation of the device , the set-up location must fulfil
the following requirements:
■ When setting it up, place the appliance on a firm, flat and horizontal
surface.
■ Do not place the device in a hot, wet or extremely damp environment or in
the vicinity of flammable materials.
■ The mains power socket must be easily accessible, so that the power cable
can be easily disconnected in the event of an emergency.
Electrical connection
CAUTION
► Before you connect the appliance, compare the connection data (voltage
and frequency) on the data plate with that of your mains power network.
These data must agree so that no damage is sustained by the device.
► Ensure that the power cable is undamaged and is not routed over hot
surfaces and/or sharp edges.
► Ensure that the power cable is not taut or kinked.
► Do not let the power cable hang over edges (trip wire effect).
♦ Insert the plug into the mains mains power socket.
IB_400318_SV125C3_LB8_short.indb 7 27.09.2021 14:42:49

■ 8 │ GB│IE SV 125 C3
Functions
Button Function
wStart/cancel "sealing" function (without vacuum-
ing)
eStart/cancel "vacuuming and sealing" function
rActivate/deactivate additional function "wet"
(for particularly moist food products)
tActivate/deactivate additional function "soft"
(for pressure-sensitive foods, e.g. fruit or cakes)
zStart/cancel "external vacuuming" function (for
vacuuming using the hose and adapter)
Tips
The following table offers some useful information on optimal preparation and processing
of various food items.
Food Notes
Recom-
mended
container
Recommended
additional
function
Fish/meat
–use only when fresh,
–do not interrupt the cold
chain
–Bag
Vegetables
–peel or wash and dry
–blanch for a few minutes in
boiling water, rinse with ice
water and dry to avoid loss
of flavour and colour or gas
formation* during storage
–Bag
IB_400318_SV125C3_LB8_short.indb 8 27.09.2021 14:42:50

GB│IE │ 9 ■
SV 125 C3
Food Notes
Recom-
mended
container
Recommended
additional
function
Leafy vegeta-
bles/lettuce
–wash and dry
–not suitable for freezing –Container
Fruit –peel or wash and dry
–Refrigerator:
container
–Freezer: bag
Herbs –wash and dry
–whole sprig –Bag
Baked products
–Container
–Bag
Powdery food
–place a piece of kitchen
paper in the top of the bag/
container or vacuum seal in
the original packaging
–Bag
–Container
Cold liquids
–Container
–freeze briefly, if necessary –Bag
Cooled,
cooked foods
–Container
–Bag
*Applies, for example, to all types of cabbage (broccoli, Brussels sprouts, kale, etc.),
asparagus, sugar snap peas, beans, romanesco and pak choy.
IB_400318_SV125C3_LB8_short.indb 9 27.09.2021 14:42:50

■ 10 │ GB│IE SV 125 C3
Welding a tube film
NOTES ON THE FILM
► The film width may not exceed 30 cm. Otherwise it cannot be welded
correctly.
► Use only nylon PA/PE films with a structure (dots or grooves) on one side
and a thickness of approx. 0.17–0.29 mm (170–290 μ) in this device.
Otherwise, the weld seam will not be tight and the appliance may be
damaged. You can recognise films of this type from the information on the
packaging. The quality of the weld seam will vary depending on the type
and thickness of the film.
► The supplied film is suitable for temperatures between -20°C and +110°C.
► The supplied foil is BPA-free and microwaveable. However, never heat
completely sealed bags in the microwave. The bag could burst! One side
of the bag must be open. Heat the bags for no more than 3 minutes at a
maximum temperature of 900 W.
1) Cut the desired length for your bag from the tube film using a pair of scissors.
Cut as straight as possible.
2) Open the appliance lid 1by pressing the lid release 8and opening the
lid 1upwards.
3) Lay the open end of the bag as far into the appliance so that the opening of
the bag is located centrally under the lower sealing ring 5. The bag should
be inserted no further than the rear limiters 6and must lie between the front
limiters 7. If the bag lies over one or both of the two limiters 6/7, then the
bag cannot be correctly welded.
IB_400318_SV125C3_LB8_short.indb 10 27.09.2021 14:42:50

GB│IE │ 11 ■
SV 125 C3
NOTE
►The bag opening must lie flat on the welding wire 4. Otherwise the weld-
ing does not work properly.
4) Close the appliance lid 1. The press seal qpresses the bag onto the welding
wire 4, to create a smooth seam. Ensure that both corners of the appliance
lid 1click closed. If necessary, press them down once again on the markings
and so that the appliance lid 1clicks into place and locks shut.
5) Press the button w. The control lamp wlights up. As soon as the sealing
process is completed, the control lamp wflashes briefly and then goes out.
NOTE
►You can halt the sealing process at any time by pressing the button w
again. The control lamp wflashes and then goes out.
IB_400318_SV125C3_LB8_short.indb 11 27.09.2021 14:42:50

■ 12 │ GB│IE SV 125 C3
CAUTION – PROPERTY DAMAGE!
If the control lamp wdoes not turn off after a maximum of
10 seconds during the sealing process, the appliance is
defective!
► Remove the plug from the mains power socket immediately. Do not attempt
to repair the appliance yourself. Contact the Customer Service department.
6) Open the appliance lid 1by pressing the lid release 8and flipping the lid 1
upwards. Remove the bag. This is now sealed at one end.
NOTE
► Ensure that the weld seam is properly closed. A correct weld seam should
be a smooth, straight stripe without any creases.
7) Fill the bag. You must leave at least 6 cm of the bag free up to the edge to
be welded.
CAUTION – PROPERTY DAMAGE!
► Fill the bag so that no food scraps or liquids can leak out during welding
and get into the appliance.
8) If you do not want to vacuum the bag, you can now weld the other, open side.
NOTE
► Wait a few seconds to allow the appliance to cool down before sealing
the next bag.
During this cool-down phase, you cannot start the “seal” function.
IB_400318_SV125C3_LB8_short.indb 12 27.09.2021 14:42:50

GB│IE │ 13 ■
SV 125 C3
Vacuum sealing
Vacuuming the tube film
You can also suck the air out of the bag (vacuum) during welding:
NOTE
►If you want to vacuum seal bags with liquid contents only, it is best to
freeze the liquid briefly so that it does not get sucked into the appliance
during vacuuming. If small quantities of liquid or food nonetheless get
sucked up, they will be deposited in the small drip tray that is located
within the lower sealing ring 5.
1) Lay the open end of the bag as far into the appliance so that the opening of
the bag is located centrally under the lower sealing ring 5. The bag should
be inserted no further than the rear limiters 6and must lie between the front
limiters 7. Otherwise the vacuuming and welding will not function correctly:
2) Close the appliance lid 1. Ensure that both corners of the appliance lid 1
click closed. If necessary, press them down once again on the markings
and so that the appliance lid 1clicks into place and locks shut.
IB_400318_SV125C3_LB8_short.indb 13 27.09.2021 14:42:51

■ 14 │ GB│IE SV 125 C3
NOTE
► Ensure that the upper 0and the lower sealing rings 5are not damaged!
Otherwise the device cannot suck the air out of the bag.
► If either one of the sealing rings 0/5is damaged, simply pull it out of the
groove and press the replacement sealing ring into the groove.
3) If necessary, select the appropriate additional function for your food.
Otherwise, you can skip this step and continue with point 4):
–Press the button r if you want to vacuum a particularly moist or
juicy food, such as freshly marinated meat or cut fruit.
If there is moisture between the film and the seam, this can lead to defec-
tive seals. When this function is activated, the sealing time is increased
so that the seal is more stable.
If the additional function “wet” is activated, the corresponding
control lamp rlights up.
–Press the button tif you want to vacuum seal pressure-sensitive
foods such as cakes or berries. When the additional function “soft” is
activated, the suction pressure is slightly reduced and the food is not
squeezed as much.
If the additional function “soft” is activated, the corresponding
control lamp tlights up.
NOTE
► If you want to vacuum a moist and pressure-sensitive food, you can also
activate both additional functions simultaneously.
4) Press the button e. The control lamp elights up and the appliance
sucks the air out of the bag. As soon as all the air is sucked out, the control
lamp wlights up. The appliance now seals the bag. As soon as the seal-
ing process is completed, both control lamps e/wflash and then go out.
5) Once both control lamps e/whave gone out, you can open the lid by
pressing the lid releases 8and flipping the lid 1upwards. Remove the
vacuum-sealed bag.
IB_400318_SV125C3_LB8_short.indb 14 27.09.2021 14:42:51

GB│IE │ 15 ■
SV 125 C3
NOTE
► You can stop the vacuuming process at any time by pressing the button
eagain. The corresponding control lamp egoes out. Press the
button eagain to resume the vacuuming process.
If the appliance has already switched to the sealing process and the control
lamp wis also lit, the process can be stopped with the button w.
The control lamps e/wflash and then go out. The appliance then stops
the sealing process.
► Once you have sealed 5 bags in a row, allow the appliance to cool down
for about 1 minute. During this cool-down phase, it is possible that you
cannot start the appliance.
After the cool-down phase, you can use the appliance as normal (even if a
whole minute has not yet elapsed).
TIP – SOUS-VIDE COOKING
► As the supplied film is suitable for temperatures between -20°C and
+110°C, it can be used for sous-vide cooking (vacuum cooking). "Sous-vide"
is French and means "under vacuum". In vacuum cooking, the food (usual-
ly fish or meat, but vegetables can also be used) is vacuum-sealed in a bag
and then cooked in water or steam cooked at a relatively low temperature
(50° to 90°C). The advantage of this is that volatile flavours and aromas
are not lost during cooking. The food does not dry out and the vitamins
and flavours are preserved. Herbs or spices that are vacuum-sealed in the
bag with the food give off a more intense flavour.
Vacuuming containers and resealable bags
NOTE
► If you want to vacuum seal containers or bags with liquid contents only, it
is best to freeze the liquids briefly so that they do not get sucked into the
appliance during vacuum sealing. If small quantities of liquid or food none-
theless get sucked up, they will be deposited in the small drip
tray that is located within the lower sealing ring 5.
You can vacuum seal containers and resealable bags using the vacuum hoses u
and appropriate adapters i/o/psupplied with the appliance.
IB_400318_SV125C3_LB8_short.indb 15 27.09.2021 14:42:51

■ 16 │ GB│IE SV 125 C3
NOTE
► You can order suitable bags and containers separately. Please refer to
section "Ordering spare parts and accessories".
► The vacuum hoses uand adapters i/o/pare also compatible with
bags and containers made by other manufacturers.
Adapters e.g. suitable for
Adapter A iCASO* (VacuBoxx series), Ernesto,
various bags with a valve
Adapter B o
FoodSaver** (FFC02XX, FFC002X, 003X,
005X, 008X, 010X storage containers,
lunchbox set T020-00024), various bags
with a valve
Adapter C p
CASO* (vacuum container set, wine
stoppers), FoodSaver** (container set
FSC003)
*CASO is a registered trademark of Caso Holding GmbH.
**FoodSaver is a registered trademark of Sunbeam Products, Inc.
Vacuuming sealing bags
1) Connect the vacuum hose uonto the suction fitting 9of the appliance.
2) Select the appropriate adapter A/B i/ofor the bag you want to vacuum
and attach it to the vacuum hose u.
3) Close the appliance lid 1. Ensure that both corners of the appliance lid 1
click closed. If necessary, press them down once again on the markings
and so that the appliance lid 1clicks into place and locks shut.
4) Close the bag to be vacuum sealed carefully. Vacuum sealing only works
properly if the bag is completely closed off. Position the bag so that the
extraction opening of the bag is lying on a smooth surface.
5) Press the adapters A/B i/ofirmly onto the round extraction opening on
the bag.
6) Press the button z. The control lamp zlights up and the appliance
sucks the air out of the bag. As soon as all the air is sucked out, the control
lamp zgoes out.
7) You can now remove the adapter A/B i/o from the bag.
Vacuum sealing containers
1) Connect the vacuum hose uonto the suction fitting 9of the appliance.
2) Select the appropriate adapter i/o/pfor the container you want to
vacuum and attach it to the vacuum hose u.
IB_400318_SV125C3_LB8_short.indb 16 27.09.2021 14:42:51

GB│IE │ 17 ■
SV 125 C3
3) Close the appliance lid 1. Ensure that both corners of the appliance lid 1
click closed. If necessary, press them down once again on the markings
and so that the appliance lid 1clicks into place and locks shut.
4) Connect the adapter i/o/p to the appropriate fitting on the container.
Please refer to the instruction manual of the container for further information.
5) Press the button z. The control lamp zlights up and the appliance
sucks the air out of the container. As soon as all the air is sucked out, the
control lamp zgoes out.
6) You can now remove the adapters i/o/pfrom the container and the
appliance.
Cleaning
DANGER
Risk of fatal injury from electrocution!
► Remove the plug from the mains power socket before beginning to clean
the device.
► Ensure that no moisture can penetrate the device during cleaning.
CAUTION
Possible damage to the appliance.
► Do not use aggressive or abrasive cleaning agents, as these may corrode
the surface of the casing.
► Do not use any hard or sharp objects to remove any adhesive from the
welding wire 4. Otherwise the welding wire 4or the insulation could
be damaged.
Cleaning the appliance
♦ Clean the surface of the housing of the appliance with a lightly moistened
cloth and a mild detergent.
♦ Wipe off the upper 0and the lower sealing rings 5, as well as the press
seal qwith a damp cloth. Ensure that the appliance is dry before using it again.
♦ Wipe the vacuum hoses u, and the adapters i/o/p with a damp cloth. If
there is heavy soiling, you can also clean these parts in hot water with a little
detergent. Ensure that all components are completely dry before the next
use.
♦ Clean the drip tray that is located between the lower sealing ring 5in warm
water with a little detergent.
You can also clean the drip tray in the dishwasher, if required. Make
sure that the drip tray does not get jammed in the dishwasher. Use
the upper basket in the dishwasher if possible.
IB_400318_SV125C3_LB8_short.indb 17 27.09.2021 14:42:51