Silvercrest OMC807 User manual

HOME TECH
PC Wireless Mouse
with charging base and USB nano receiver
Mysz bezprzewodowa
Z ładowarką i odbiornikiem
USB Nano
Instrukcja obsługi oraz
informacje o serwisie
PL
PC Wireless Mouse
with charging base and
USB nano receiver
User manual and service
information
GB
PC-bežični miš
Sa stalkom za punjenje i USB-Nano-prijemnikom
Korisnički priručnik i informacije o servisu
HR
OMC807

Mouse with charging cradle OMC807
English - 1
Overview
1 Zoom - (default mode)
Play / Pause (media mode)
2 Zoom + (default mode)
Launch Media Player (media mode)
3 Forward (default)
Next title (media mode)
4 Back (default)
Previous title (media mode)
5 Left mouse button
6 Right mouse button
7 Tilt wheel (4-way scroll wheel)
Volume control and mute (media mode)
8 Rechargeable battery level indicator
9 800/1600 cpi toggle switch (press briefly)
Standard / media mode toggle switch
(keep pressed for 3 seconds)
10 Charging indicator

Mouse with charging cradle OMC807
2 - English
Contents
Overview ..........................................................................................1
Important Safety Instructions ........................................................... 3
Intended Use ................................................................................3
Operating Environment................................................................. 4
Children and Persons with Disabilities .........................................5
Rechargeable Battery...................................................................5
R/F Interface.................................................................................6
Repair and Maintenance............................................................... 7
Copyright ......................................................................................7
Storing When Not Using the Product............................................ 7
Conformity Notice .........................................................................8
Disposal of Old Devices................................................................8
Package Contents............................................................................9
Introduction.......................................................................................9
System Requirements....................................................................10
Hardware Installation......................................................................10
Inserting the Rechargeable Battery ............................................10
Connecting the USB Nano Receiver ..........................................12
Software Installation.......................................................................13
Operation........................................................................................15
Toggling between Operating Modes...........................................15
Configuration ..............................................................................15
Attachment .....................................................................................17
Troubleshooting..........................................................................17
Technical Data............................................................................ 18
Warranty Information......................................................................19

Mouse with charging cradle OMC807
English - 3
Important Safety Instructions
Before you use this device for the first time, please read the
following notes in this manual and heed all warnings, even if you
are familiar with handling electronic devices. Keep this manual safe
for future reference. If you sell the device or pass it on, it is
essential you hand over this manual also.
This icon denotes important information for the safe
operation of the product and for the user’s safety.
This icon alerts about a strong light source.
This symbol denotes further information on the topic.
Warning: LED Radiation! LED Class 1
Avoid harm to the eyes! Never look into the LED beam. Never point
the LED beam directly at people or animals!
Intended Use
This wireless mouse, consisting of an optical mouse charging
cradle and USB nano receiver, is an IT device. The device may not
be used outdoors or in tropical climates. This product has not been
designed for corporate or commercial (e.g. office) applications. Use
the product in domestic environments for private applications only.
Only connection cables and external devices may be used that
comply with safety standards and the electromagnetic compatibility
and shielding quality of this device. This device fulfils all that relates

Mouse with charging cradle OMC807
4 - English
to CE Conformity, relevant norms and standards. Any modifications
to the equipment other than recommended changes by the
manufacturer may result in these directives no longer being met.
The manufacturer is not liable for any damage or interference
caused by unauthorized modifications. Only use the accessories
recommended by the manufacturer. Any use other than that
mentioned above does not correspond to the intended use.
If you are not using the device within the Republic of Germany, you
must observe the regulations and laws in the country of use.
Operating Environment
Position the wireless mouse on a stable, even surface and do not
place any objects on the device. The device is not for use in
environments with a high temperature or humidity (e.g. bathrooms),
and must be kept free of dust. Operating temperature and operating
humidity: 5°C to 40°C, max. 90% RH.
Always make sure that:
-no direct heat sources (e.g. heating) can affect the device;
-no direct sunlight or artificial light reaches the device;
-contact with spray, dripping water and corrosive liquids must be
avoided and the device should never be operated near water,
and it must especially never be immersed (do not place any
objects filled with liquids such as vases or drinks near the
device);
-the device is never placed in the immediate vicinity of magnetic
fields (e.g. loudspeakers);
-no fire sources (e.g. burning candles) are placed on or near the
device;
-no foreign bodies are introduced into the device;
-the device should not be subject to any sharp temperature
changes;
-the device is not subject to excessive shocks and vibrations;

Mouse with charging cradle OMC807
English - 5
Children and Persons with Disabilities
Electrical appliances do not belong in the hands of children. Also
people with disabilities shall use electrical devices accordingly. Do
not allow children or persons with disabilities to use electrical
devices when not under supervision. These people may not
comprehend the presence of potential risks. Batteries and small
parts represent potential choking hazards. Keep the batteries out of
reach. If a battery is swallowed, seek medical help immediately.
Keep the packaging away from children and persons with
disabilities too. as there is danger of suffocation.
Rechargeable Battery
Insert the rechargeable battery with the correct polarity. Never
throw the rechargeable battery into fire. Remove the rechargeable
battery when the device is not to be used for a long time. Non-
intended use may cause explosion and danger to life.
Never use a conventional (non-rechargeable) battery instead of a
rechargeable battery. Only use rechargeable batteries of the same
type.

Mouse with charging cradle OMC807
6 - English
R/F Interface
Please switch off the appliance in airplanes, hospitals, operating
theatres and in the vicinity of medical electronic system. The radio
waves transmitted could impair the functionality of sensitive
appliances.
Observe a minimum distance of 20 cm between the appliance and
any pacemaker as the radio waves could impair the function of the
pacemaker.
The transmitted radio waves may create interference noises in
hearing aids.
Do not allow the appliance to be introduced in the vicinity of
inflammable gases or in environments subject to a risk of explosion
(e.g. paint shops) as long as the radio component is switched on,
because the transmitted radio waves could trigger an explosion or
fire.
The coverage/range of the radio waves varies depending on the
surrounding and environmental conditions.
In any data exchange via wireless connections, unauthorized third
parties are also able to receive the data. Targa GmbH is not liable
for any radio or television interference caused by unauthorized
modifications of this appliance. Targa furthermore accepts no
liability for the replacement or exchange of connection cables and
appliances not specified by Targa GmbH. The user is solely
responsible for the elimination of interferences caused by such an
unauthorized modification, as well as for the replacement or
exchange of the appliances concerned.

Mouse with charging cradle OMC807
English - 7
Repair and Maintenance
Repairs are required when this device has been damaged in any
way, for example, when liquid has entered the product, when the
product has been exposed to rain or moisture, when the product
does not work normally or if the product has been dropped. If
smoke, unusual noises or smells are noticed, power off the device
immediately. In this case the device should not be used further and
should be inspected by authorized service personnel. Please
contact qualified personnel when repair is needed. Never open the
housing of the device, or the accessories. Only use a clean, dry
cloth for cleaning. Never use any corrosive liquids.
Copyright
The entire content of this User’s Manual is copyrighted and is
provided to the reader for information purposes only.
Copying data and information without the prior written and explicit
authorization from the author is strictly forbidden. This also applies
to any commercial use of the contents and information.
All texts and figures are up-to-date as per the date of print release.
We assume no liability for any changes.
Storing When Not Using the Product
When left unused for a long period of time, remove the batteries
from the wireless mouse. Remove the USB nano receiver from your
computer’s USB port and insert it into the storage compartment of
the mouse. Also make sure that the storage temperature is
maintained between 5 °C and 40 °C. Humidity must not exceed
90% RH.

Mouse with charging cradle OMC807
8 - English
Conformity Notice
The wireless mouse has been tested and approved
for compliance with the basic and other relevant
requirements of the R&TTE Directive 1999/5/EC. The
corresponding Declaration of Conformity can be found
at the end of this User's Manual.
Disposal of Old Devices
Devices marked with this symbol are subject to the
European Directive 2002/96/EC. All electric and
electronic devices must be disposed of separately
from household waste at established bodies. The USB
nano receiver is also an electronics device and must
be properly disposed of.
Avoid hazards to the environment and dangers to your personal
health by disposing of the device properly. For further information
about proper disposal, contact your local government, disposal
bodies or the shop where you bought the device.
Respect the environment. Old batteries do not belong in with
domestic waste. They must be handed in to a collection point for old
batteries.
Also recycle the packaging material properly. Cardboard packaging
can be taken to paper recycling containers or public collection
points for recycling. Any films or plastic contained in the packaging
should be taken to your public collection points.

Mouse with charging cradle OMC807
English - 9
Package Contents
Please check the completeness of package contents using the
following list:
-Wireless mouse OMC807
-Charging cradle
-USB nano receiver
-1 rechargeable battery, type AA, 1.2V, 1300mAh
-Driver CD
-User's Manual
If you find any items missing or damaged, please phone our hotline.
You will find the corresponding phone number in the last chapter
“Warranty Information”.
Introduction
Thank you for purchasing the wireless mouse SilverCrest OMC807.
Besides the 3 standard buttons, this optical wireless mouse is
equipped with five special buttons for easier access to frequently
used functions. The scrolling wheel is a tilt wheel enabling you to
scroll in horizontal as well as vertical directions. The special CPI
button (9) puts you in a position to toggle between the optical
resolutions of 800 cpi and 1600 cpi or between standard and media
operation. The wireless mouse features an automatic standby
function. When not using the wireless mouse for a certain time, it
will power off. Press any button on the wireless mouse to power it
back on.

Mouse with charging cradle OMC807
10 - English
System Requirements
-Intel®Pentium®III / AMD Athlon™ or higher
-1 free USB 2.0 port
-Microsoft®Windows®XP, Windows Vista®or Windows®7
-CD-ROM drive or DVD drive for installing the software
Hardware Installation
Inserting the Rechargeable Battery
Never use a conventional (non-rechargeable)
battery instead of a rechargeable battery. You must
never place the mouse on the charging cradle with a
conventional (non-rechargeable) battery inserted
into it.
Please charge the battery before first use of the product. To do this,
insert the battery into the wireless mouse and then place the mouse
onto the connected charging cradle.

Mouse with charging cradle OMC807
English - 11
11 Optical sensor
12 Inserted USB nano receiver
13 On/Off button
14 Charging contacts
Open the battery compartment on the bottom of the wireless
mouse.
Insert the supplied rechargeable battery (size AA) into the
wireless mouse and make sure that the battery is properly
aligned according to the polarity (+ and -) (see figure).
Remove the USB nano receiver
Close the battery compartment.
Press the On/Off button (13) on the bottom of the wireless
mouse to power it on.
Plug the USB cable of the charging cradle into a free USB port
on your powered-on computer. The charging indicator (10)
blinks. Please wait a moment until the charging indicator stops
blinking.
Place the wireless mouse onto the charging cradle.
During charging the charge indicator (10) will light orange.
When the charging process is completed, the charging indicator
will light green.
If the indicator light (8) on the upper side of the
wireless mouse lights orange, the rechargeable
battery is exhausted. Then place the wireless mouse
onto the charging cradle.
Should the wireless mouse fail to work, power it off
and back on. Sometimes removing and re-inserting
the batteries will also help.

Mouse with charging cradle OMC807
12 - English
After inserting a rechargeable battery into the mouse
or powering the mouse on, the indicator (8) will flash
several times during automatic synchronisation with
the receiver. When the synchronisation is completed,
the status indicator will stop lighting.
The power for charging the battery is obtained from
the computer’s USB port. Depending on your
computer, the USB power may be cut when the
computer is powered off. In this case, you may only
charge the wireless mouse battery when the
computer is powered on.
Connecting the USB Nano Receiver
Connect the USB Nano Receiver (12) to a free USB port of your
running computer.
The operating system will automatically recognize the new
hardware and install the required drivers. Depending on the
operating system installed, the following screen messages may
appear:
Windows®XP
When the receiver is connected for the first time, the operating
system displays the message „New hardware detected“. Wait
until the message „The new hardware has been installed and is
now ready for use“ is displayed before using your mouse.
Windows Vista®, Windows®7
When the receiver is connected for the first time, the operating
system displays the message „Installation of appliance driver
software“. Wait until the message „The appliances are ready for
use now“ appears. The mouse is now operational and ready to be
used.
If your previous mouse is still connected to the computer, please
shut down the computer, disconnect the appliance and then restart
the computer.

Mouse with charging cradle OMC807
English - 13
Software Installation
If you would like to use all of the functions of your wireless mouse
you need to install the software included. Insert the included CD-
ROM in the CD-ROM drive of your computer. The installation
process should start automatically, failing that, start the CD-ROM
file "setup.exe" manually by double-clicking it.
Only with the operating system Windows®7, Windows Vista®will
the installation initially be stopped by the user account control
function with the message: „An unidentified program is attempting
to access the computer”. Click on „OK“ to continue with the
installation.
The following installation illustrations correspond to the operating
system Windows®7, Windows Vista®. The windows shown in the
operating system Windows®XP are slightly different, but their
content is the same.
Click on Next to start the
installation.

Mouse with charging cradle OMC807
14 - English
Here you can select the target file
for the installation via the Browse
button or use the suggested file.
Click on Next to proceed with the
installation.
Click “Finish” to finish the setup
programme.

Mouse with charging cradle OMC807
English - 15
Operation
Toggling between Operating Modes
The CPI button (9) puts you in a position to toggle between the
optical scan resolutions of 800 cpi und 1600 cpi. The scanning is
more precise at 1600 cpi and the mouse cursor will move faster
given the same movements.
If you would like to toggle between standard operation and media
operation, press the CPI button (9) and keep it pressed for a
minimum of 3 seconds until the power control lamp (8) briefly lights
up. Please see the list on page 1 for information on the functions
available in the media operation mode.
Configuration
Double-click on the icon in the task bar (lower-right corner on
your screen, near the system clock). Or right-click on the icon and
select “Open” from the context menu. The mouse configuration
menu will appear.
Here you can specify functions
for selected mouse buttons.
Simply click on the selection
switch next to the corresponding
mouse button and select a
function from the menu by
clicking on it with the left mouse
button.
You can restore the mouse to its
original state by clicking on the
„Restore to default“ button.
All selected options apply to the default mode. The
button assignments for media mode cannot be
modified.

Mouse with charging cradle OMC807
16 - English
If you would like to apply your changes, please click on the „Apply“
button (the window will still stay open) or the „OK“ button (the
window will close).
Tip for users of Microsoft®Windows®7, Windows Vista®
(Windows®XP does not include this function):
You can also adjust the horizontal scrolling of the tilt wheel in the
system control of the operating system in the submenu „Mouse“.
The configuration menu of the mouse driver needs to be closed in
order to access the system control menu.

Mouse with charging cradle OMC807
English - 17
Attachment
Troubleshooting
If the wireless mouse is not being recognized following installation
or does not respond to input, please check the following:
;Please check the polarity of the rechargeable battery.
;Please check if the wireless mouse is switched on.
;Check whether the miniature USB receiver is properly
connected to the computer; see page 12 – Connecting the
USB Receiver).
;Try another USB port.
;Check the charging level of the battery and, if necessary,
insert a new rechargeable battery.
;Please note that you need to use a mat (e.g. mouse pad) if
you intend to use the mouse on a glass surface or glossy
surface.

Mouse with charging cradle OMC807
18 - English
Technical Data
-Wireless optical mouse with miniature USB receiver
-8 buttons, 7 of which are programmable
-Tilt wheel for vertical and horizontal scrolling
-Selectable resolution: 800 cpi or 1600 cpi
-Smart Link (no complicated connection process required for
receiver and mouse)
-Radio frequency: 2.4 GHz
-Power supply: 1 rechargeable battery, type AA, 1.2 V, NiMH,
1300mAh
-LED Class 1
-Toggling between Media Player and Office Mode (standard
operation) by simple key operation
-Range: up to 5m
-Power supply for charging cradle:
5 V via computer USB port
-Dimensions of wireless mouse:
125 mm x 75 mm x 40 mm (LxWxH)
-Dimensions of USB nano receiver:
15,4 mm x 6,9 mm x 18,1 mm (LxWxH)
-Dimensions of charging cradle:
100 mm x 81 mm x 38 mm (LxWxH)
-Weight of wireless mouse: 85 g
(without rechargeable battery, with USB nano receiver inserted)
-Weight of USB nano receiver: 2 g
-Weight of charging cradle: 81 g

Mouse with charging cradle OMC807
English - 19
Warranty Information