SilverStone Mammoth MM01 User manual

Mammoth Series MM01
Professional chassis with integrated HEPA filter
for harsh or critical environments

Installation and system optimization guide:
Specification P.2
Introduction P.1
Disassemble chart P.3
Installation guide P.5
Connector definition P.17
Front I/O connector guide P.19
Component size limitations P.20
CPU and graphic card supporter P.29
Optimal Thermal Performance Layout P.32
Upgrade And Maintenance P.39
Warranty Information
P.47Q & A
P.55
The following manual and guides were carefully prepared by the SilverStone engineering team
to help you maximize the potential of your SilverStone product. Please keep this manual for
future reference when upgrading or performing maintenance on your system. A copy of this
manual can also be downloaded from our website at:http://www.silverstonetek.com

The following manual and guides were carefully prepared by the SilverStone engineering team to
help you maximize the potential of your SilverStone product. Please keep this manual for future
reference when upgrading or performing maintenance on your system.Acopy of this manual can also
be downloaded from our website at:
http://www.silverstonetek.com
Installation and system optimization guide:
Product Overview
Specifications
Disassemble Chart
Installation Guide
Connector Definition
Front I/O connector Guide
Component Size Iimitations
CPU And Graphic Card Supporter
Optimal Thermal Performance Layout
Upgrade And Maintenance
Q&A
Warranty Information
P.1
P.2
P.3
P.5
P.17
P.19
P.20
P.29
P.33
P.39
P.47
P.55

Product Overview
1
Introduction
For computer designers, creating a chassis capable of surviving harsh environments is a tough task, especially if dust
isamajorproblem. Mostresorttofanlessconfigurationasthiseliminatesthepossibilityofdustbuildupintroducedbyactive
airflow into the chassis, which is the main cause of system overheating over time. But limited heat dissipation capacity
afforded by fanless designs confines systems to lower powered CPUs and Mini-ITX boards with less features.
To overcome this limitation, SilverStone’s R&D team once again challenged and overturned convention by coming up
with an answer in the Mammoth MM01 chassis. Instead of completely sealing off airflow to prevent dust, the MM01 has a
partially-sealed design with active filtering. To prevent dust from entering the chassis, a HEPAfilter is used to cover the air
intake area, making MM01 the first retail computer chassis to incorporate this internationally recognized filtering technology.
Used frequently by clean room in factories, operating room in hospitals, or facilities requiring dust-free environment, the
HEPA filter has the ability to remove airborne particles far exceeding what’s available in traditional computer equipments.
In order for this to work without suffocating airflow, two Air Penetrator fans were selected for use in the MM01. With a
combined rating of up to 340CFM, they provide air pulling power similar to typical household fans and make it possible to
maintain proper cooling for high-end components despite the presence of highly restrictive HEPA filters.
Complementing the tremendous ability to keep dust at bay, the MM01 also has unique, downward slanting front and
rear vents to keep liquid from flowing in from the top of the chassis. This simple, yet affective design helps MM01 take on
much harsher conditions required by professionals working in places not normally suitable for computers. For those
choosingtouseMM01innormalhomeoroffice,itssuperiorfilteringcouldpotentiallyhelpcleanuptheworkingenvironment
as well!
Mammoth Series MM01

Product Overview
2
Aluminum door, plastic anti-splash grille, steel panels and body
SSI-EEB, SSI-CEB, Extended ATX, ATX, Micro-ATX
Front
SST-MM01B (black)
USB 3.0 x 2 audio x 1 MIC x 1
1 x Optional standard PS2 (ATX) no length limitation
Compatible up to 13.3” long, width restriction-6.69”
183mm
8
271mm (W) x 542mm (H) x 597mm (D), 87.69 liters
Includes HEPA filter
*AP182’s original top speed is 2000rpm, but high resistance introduced by HEPA filter reduces top speed
by 200rpm.
3.5" x 7 ( hot-swap x1 ) , 2.5” x 4
2 x AP182 180mm intake fan 500~1800rpm*, 17~42 dBA
5.25" x 2
Internal
1 x 120mm fan slotRear
Exposed
Specifications
Material
Model
Motherboard
Drive Bay
Cooling System
Expansion Slot
Front I/O Port
Power Supply
Expansion Card
Limitation of CPU cooler
Dimension
Extra
Mammoth Series MM01

Disassemble Chart
3
Secure 2.5” HDD
Secure optical drives
Secure VGAholder and claw
Secure PSU, 12025 fan, motherboard and 3.5” HDD
Motherboard standoff
VGAsupporter holder
VGAsupporter claw
Standoff socket wrench
Cable management
SCREW - P - M3 4 - BK
SCREW - THUMB - M3 6 - BK
SCREW - THUMB - 6 - 32 6 - BK
SCREW - I - 6 - 32 5 - BK
STANDOFF - 6 - 32 6.5H - 6 - 32
VGA- SUPPORT - HOLDER
VGA- SUPPORT - CLAW
STANDOFF - SOCKET - WRENCH
BUNCH - WIRE - TIES
PICTURE ITEM PURPOSE
PSU (OPTION)
TOP COVER
REAR PANEL
RIGHT PANEL
FRONT PANEL
5.25” DRIVE BAY x 2
MOTHERBOARD TRAY
180 FAN x 2 OR
120 FAN x 3 (OPTION) 3.5” DRIVE BAY x 1
3.5” DRIVE BAY x 1
2.5” DRIVE BAY x 4
120 FAN x 1 (OPTION)
3.5” DRIVE BAY x 5
HEPAFilter
LEFT PANEL
USB3.0 x 2 + SPK + MIC
RESET BUTTON
POWER BUTTON
Mammoth Series MM01
*
*
*
*
*

Disassemble Chart
4
Mammoth Series MM01

Installation guide
5
Before you begin, please make sure that you
have all components collected
check that all components do not have compatibility problems with each other or with the case
if possible, assemble the components outside the case first to make sure they are working
keep the motherboard manual ready for reference during installation
1
2
3
4
01
02
Lösen Sie die beiden Schrauben
an den linken und rechten
Seitenwänden, nehmen Sie die
Seitenwände ab.
Desserrez les vis des deux
panneaux latéraux pour les
retirer.
Desatornille dos tornillos de los
paneles izquierdo y derecho para
quitarlos.
Per rimuovere i pannelli laterali
allentare, per entrambi, le due
viti di serraggio.
Loosen two screws from both
left and right side panels to
remove them.
Отвинтите по два винта,
крепящих левую иправую
боковых панели, иснимите
панели.
왼쪽과 오른쪽 사이드 패널에서
두 개씩 나사를 풀어 사이드
패널을 제거합니다.
取下左右側板各兩顆螺絲，
卸下側板。
取下左右侧板各两颗螺丝，
卸下侧板。
両方の左右パネルからネジ
2本を緩めて、取り外します。
Entfernen Sie die obere Blende,
indem Sie sie nach hinten
drücken.
Retirez le panneau supérieur en
le poussant vers l'arrière.
Retire el panel superior tirando
de él hacia la parte posterior.
Allentare le due viti sul lato
posteriore del telaio e poi
rimuovere il coperchio superiore.
Remove top panel by pushing
it toward the rear. Снимите верхнюю панель,
переместив ее назад.
뒤쪽으로 밀어 상단 패널을
분리하십시오.
將上蓋往後推，取下上蓋。
将上盖往后推，取下上盖。
上部パネルを後方に
押して取り外します。
Mammoth Series MM01

03
04
Lösen Sie die drei Schrauben,
welche die Motherboard-
Halterung fixieren, nehmen
Sie die Halterung ab.
Desserrez les trois vis tenant le
plateau de la carte mère pour le
démonter.
Desatornille tres tornillos que
sujetan la bandeja de la placa
base para quitarla.
Per rimuovere il supporto
scheda madre allentare le
tre viti di serraggio.
Loosen three screws holding
the motherboard tray to
remove it.
Отвинтите три винта,
крепящих кронштейн
материнской платы, и
снимите его.
3개의 나사를 풀어 메인보드
트레이를 제거합니다.
取下主機板托盤3顆螺絲，
將主機板托盤抽出。
取下主板托盘3颗螺丝，
将主板托盘抽出。
マザーボードトレイを固定
しているネジ3 本を緩 めて、
取り外します。
將電源供應器由上放入機殼內，
如果有12公分或以上尺寸的
風扇建議朝下放置。
将电源供应器由上放入机壳内，
如果有12公分或以上尺寸的
风扇建议朝下放置。
Insert the power supply from
the top, if the power supply has
a build-in 120mm fan or larger,
we recommend installing the
power supply with its fan facing
down.
Установите блок питания в
верхней части корпуса. Если
блок питания оснащен
встроенным вентилятором
размером 120 мм или
больше, рекомендуется
устанавливать блок питания
вентилятором вниз.
電源は上面から入れます。電
源に120mm以上のファンが内
蔵されている場合、電源のフ
ァンが下向きになるよう設置
することを推奨します。
전원 공급장치에 120mm
이상의 내장 팬이 있는 경우,
상단에서 전원 공급장치를
삽입하십시오. 팬이 아래쪽을
향하도록 전원 공급장치를
설치하는 것이 좋습니다.
Setzen Sie das Netzteil von
oben ein; sofern das Netzteil
über einen120 mm-Lüfter (oder
größer) verfügt, empfehlen wir,
das Netzteil mit dem Lüfter
nach unten einzubauen.
Insérez la source
d'alimentation d'en haut, si la
source d'alimentation a un
ventilateur intégré de 120mm
ou plus, nous vous
recommandons d'installer la
source d'alimentation avec le
ventilateur face vers le bas.
Inserte la fuente de
alimentación desde arriba, si
la fuente de alimentación tiene
un ventilador de 120mm o
mayor incorporado, le
recomendamos instalar la
fuente de alimentación con el
ventilador hacia abajo.
Inserire l'alimentatore dall'alto,
se l'alimentatore ha una
ventola integrata da
120mm - o più grande; si
raccomanda di installare
l'alimentatore con la sua
ventola rivolta verso il basso
Installation guide
6
Mammoth Series MM01

05
06
Nehmen Sie die 3,5
Zoll-Laufwerkhalterung
heraus.
Retirez le casier des
lecteurs 3.5”.
Quite la carcasa para
dispositivos de 3,5”
Rimuovere il supporto hard
drive da 3,5”
Remove 3.5” drive cage. Извлеките кронштейн для
3,5-дюймовых жестких
дисков.
3.5” 드라이브 케이지를
제거합니다.
移除3.5吋主硬碟架。
移除3.5吋主硬盘架。
3.5インチドライブケージを取
り外します。
Lösen Sie die Schrauben,
welche den unteren
Festplattenkäfig fixieren,
nehmen Sie den Käfig ab.
Dévissez les vis pour l'enlever
en tenant la cage du lecteur
inférieur pour le retirer.
Afloje los tornillos sujetando
la carcasa para discos inferior
para retirarla.
Allentare le viti che fissano il
cage unità inferiore per
rimuoverlo.
Loosen the screws holding
the lower drive cages to
remove them.
Отверните винты крепления
нижнего отсека для жестких
дисков иизвлеките его.
하단 드라이브 케이지를
고정하는 나사를 풀어
케이지를 분리하십시오.
拆除底部硬碟架螺絲，
取下硬碟架。
拆除底部硬盘架螺丝，
取下硬盘架。
下部ドライブケージを保持
しているネジをゆるめて
取り外します。
Installation guide
7
Mammoth Series MM01