Simplicity 4553 Setup guide

Attachment
Illustrated
Parts List
Rev. 10/2007
500 N. Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
www.simplicitymfg.com
MANUFACTURING, INC.
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved. Printed In USA.2007 TP 400-4553-01-AT-SMA
Mf
g
. No. Descri
p
tion
Attachment
1694918 Catcher, Clean Sweep Triple
1734832
Part No.:

Table Of Content
s
Torque Specification Chart ..................................................................... Inside Back Cover
PRODUCT COMPONENTS PAGES
Triple Catcher Assembly ...................................................................................................................................... 4

Triple Catcher Assembly
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
1694918
The above parts group applies to the following Mfg. Nos.:
4
2007Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1694918 - Catcher
TP 400-4553-01-AT-SMA

PART NO. DESCRIPTIONREF NO QTY.
Triple Catcher Assembly
Footnotes
COVER ASSEMBLY, Triple with Decal1 1732817SM 1 SCREW, #10 - 24 x 5/82004x21MA2
HANDLE, Cover3 054537MA 1 LOCKNUT, #10 - 24, ESNA4 1933896SM 2 EDGING, 11" Long PVC5 1732870SM 3 BAG ASSEMBLY, Triple6 1732351SM 3 PLUG, Round7 054776MA 8 TUBE, Round Bag8 054753E701MA 4 PLUG, Square9 054777MA 2 NUT, Centerlock Flange, 5/16 - 1810 1935048SM 9 CAPSCREW, 5/16 - 18 x 211 1921978SM 6 TUBE, Square12 054761MA 1 LOCKNUT, 1/4 - 20, Keps13 1928372SM 6 SCREW, 1/4 - 20 x 1/2, Slotted14 004x24MA 5 PIN, Cover Hinge15 054407ZMA 1 HINGE, Cover16 054754E701MA 1 PIN, Hair17 1960074SM 1 CHANNEL ASSEMBLY18 1732869SM 1 CAPSCREW, 5/16 - 18 x 2-1/419 1921160SM 2 PIN, Channel Mount20 1732565SM 1 MOUNT ASSEMBLY, Channel21 1732067ASM 1 PIN, Hair22 1960033SM 1 BOLT, Shoulder, 5/16 - 1823 1728976SM 2 NUT, Speed, 5/16 - 1824 1960717SM 2 ELBOW, Upper Tube25 1732446SM 1 TUBE, Clear26 1732552SM 1 SCREW, 1/4 - 20 x 127 004x71MA 1 HANDLE, Tube28 054416ZMA 1 STRAP, Rubber29 2171600SM 2 NUT, Centerlock Flange, 1/4 - 2030 1930642SM 2 BOOT, 44/50" Mower31 1731426SM 1 PIN, Latch32 054563MA 1 BOLT, Carriage, 1/4 - 20 x 5/833 1960252SM 1 NUT, Whizlock Flange, 5/16 - 1834 1927557SM 11 ROD, Boot Mount35 1731428SM 1 SCREW, Whizlock, 5/16 - 18 x 1-1/436 1930595SM 1 SCREW, 5/16 - 18 x 3/437 1960371SM 1 PLATE, Rod Mount38 1726578ASM 1 BOLT, Carriage, 5/16 - 18 x 5/839 1931332SM 9 BAFFLE, R.H. 44"40 1731990ASM 1 BAFFLE, R.H. 50"40 1726364ASM 1 BAFFLE, L.H. 44"41 1716879ASM 1 BAFFLE, L.H. 50"41 1716870ASM 1 ID LABEL/SERIAL PLATE (Not Serviceable)42 ----- 1
The above parts group applies to the following Mfg. Nos.:
5
2007Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1694918 - Catcher
TP 400-4553-01-AT-SMA

Triple Catcher Assembly
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
1694918
The above parts group applies to the following Mfg. Nos.:
6
2007Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1694918 - Catcher
TP 400-4553-01-AT-SMA

PART NO. DESCRIPTIONREF NO QTY.
Triple Catcher Assembly
Footnotes
OVERLAY, Mylar (Not Serviceable)43 ----- 1 SCREEN44 1732492SM 1 SCREEN SUPPORT45 1732493SM 1 RIVET, Pop46 1673320SM 18 WASHER47 1910531SM 12 FASTENER48 1732490SM 5 DECAL, Cover Warning49 1732819SM 1 INSTRUCTION MANUAL-- 1732353 1
The above parts group applies to the following Mfg. Nos.:
7
2007Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1694918 - Catcher
TP 400-4553-01-AT-SMA

Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Hardware
Grade
SAE Grade 2 SAE Grade 5 SAE Grade 8
Size Of in/lbs in/lbs in/lbs
Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.
8-32 19 2.1 30 3.4 41 4.6
8-36
20 2.3 31 3.5 43 4.9
10-24
27 3.1 43 4.9 60 6.8
10-32
31 3.5 49 5.5 68 7.7
1/4-20
66 7.6 810.9 12 16.3
1/4-28
76 8.6 10 13.6 14 19.0
5/16-18 11 15.0 17 23.1 25 34.0
5/16-24 12 16.3 19 25.8 27 34.0
3/8-16 20 27.2 30 40.8 45 61.2
3/8-24 23 31.3 35 47.6 50 68.0
7/16-14 30 40.8 50 68.0 70 95.2
7/16-20 35 47.6 55 74.8 80 108.8
1/2-13 50 68.0 75 102.0 110 149.6
1/2-20 55 74.8 90 122.4 120 163.2
9/16-12 65 88.4 110 149.6 150 204.0
9/16-18 75 102.0 120 163.2 170 231.2
5/8-11 90 122.4 150 204.0 220 299.2
5/8-18 100 136 180 244.8 240 326.4
3/4-10 160 217.6 260 353.6 386 525.0
3/4-16 180 244.8 300 408.0 420 571.2
7/8-9 140 190.4 400 544.0 600 816.0
7/8-14 155 210.8 440 598.4 660 897.6
1-8 220 299.2 580 788.8 900 1,244.0
1-12 240 326.4 640 870.4 1,000 1,360.0
Hex Head Capscrew
Hex Nut
Lockwasher
Washer
Carriage Bolt
NOTES
1. These torque values are to be used for all hardware
excluding:locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
Hardware Identification & Torque Specifications
Common HardwareTypes
Screw, 1/2 x 2
Body
Diameter
Body
Length
Inside
Diameter
Nut, 1/2”
No
Marks
3/8”Bolt or Nut
Wrench—9/16”
3/8
5/16”Bolt or Nut
Wrench—1/2”
5/16
1/4”Bolt or Nut
Wrench—7/16”
1/4
1/2”Bolt or Nut
Wrench—3/4”
1/2
DIA.
7/16
DIA.
7/16”Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
Wrench & Fastener Size Guide
Standard Hardware Sizing
When a washer or nut is identified as 1/2”, this is the
Nominal size , meaning the inside diameter is 1/2 inch; if a
second number is present it represent the
threads per inch
When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the
Nominal size , or body diameter is 1/2 inch; the
second number represents the
threads per inch (16 in this
example, and the final number is the
body length of the
bolt or screw (in this example 2 inches long).
The guides and ruler furnished below are designed to
help you select the appropriate hardware and tools.
0
1/4 3/4
1/2
1
1/4 3/4
1/2
2
1/4 3/4
1/2
3
1/4 3/4
1/2
4