Simx Lighting WP COMPACT User manual

WP COMPACT
Bulkhead
LHT0785 150W / LHT0786 200W
TECHNICAL SPECIFICATIONS
IMPORTANT
Thank you for purchasing the Simx Lighting WP Compact
Bulkhead. This product is suitable for areas that recieve
direct rainfall. It requires a 230V AC power supply to
operate and should be installed by a registered electrician.
Please read this manual before installation and retain for
future reference.
This product is suitable for use only with a supply voltage of 220-240V AC 50Hz.
All electrical work must be carried out in accordance with local and national electrical codes as applicable.
We strongly recommend that this light fitting is installed by a registered electrician.
Always switch power off prior to installation. A means of mains power isolation must be installed in the circuit
for the purpose of safe access for any internal cleaning, recalibration, or maintenance.
This light fitting is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Young children should be
supervised to ensure that they do not play with the appliance.
Any changes or modifications made or attempted to this product, without the prior written approval of
themanufacturer, will void any and all stated warranties.
LHT0785 LHT0786
Lamp Wattage 10W 15W
Lumens 900lm 1250lm
Power Factor 0.95 0.95
Power 220V - 240V AC 50Hz Class II
LED Colour 4000K
CRI > 80
Rated Life L70 B10 50,000 hours
Unit colour Grey/Opal
IP Rating, Impact protection IP65, IK08
Construction UV Polycarbonate, Stainless steel screws
INSTALLATION INSTRUCTIONS
BEFORE YOU START
Please read all the instructions prior to installation.
This light fitting is rated to IP65, making it suitable for areas that recieve direct rainfall. Please ensure the
desired location does not exceed that rating. Do not install this light in any location where the ambient
temperature is likely to exceed 45°
It is designed for wall or ceiling mount installation only, with optimum performance when mounted between
1.4-2.4 metres above the ground.
245/350mm
70mm
125mm

INSTALLATION
WP Compact is a Class II Fitting and does not need to be Earthed.
Waterproof cable should be used for outdoor installations. Using twin 2 core round flexible cable at least 1mm2
gauge is recommended.
We strongly recommend this light fitting is installed by a registered electrician
Switch off the power supply before commencing any electrical work.
Unscrew the front lens of the light to remove, partially unscrew and pivot the light away from the keyhole slot to
expose terminal block.
Position the unit against the wall in the desired location, ensuring the power supply cable can easily enter the
fitting through the rubber grommet at the rear of the fitting.
Use the holes in each corner of the fitting to mark the 4 drill holes required to secure the base to the wall (and
mark the cable inlet location if required) Care should be taken to avoid drilling or screwing into concealed
electrical wiring/plumbing.
Drill and fit the wall plugs supplied. Use a sharp knife to cut a small ‘X’ in the rubber gromet and feed the
round power supply cable through into the light fitting from beneath the unit to avoid moisture migration.
The light fitting can now be fixed to the wall using the mounting screws provided. Strip cable insulation 6mm
and attach to the terminal block following the label denotations. Refix and secure light assembly to base and
refix front lens firmly.
PRODUCT COMPLIANCES
This product conforms to relevant AZ/NZS standards.
MANUFACTURERS EXTENDED WARRANTY
This product is guaranteed by SIMX Ltd and Ventair Pty Ltd for 3 Years from the date of purchase
against faulty materials or workmanship which affects its designed ability to detect or switch. During this
period if the product has a defect of this nature it will be repaired or replaced free of charge by SIMX with
the same item, or a similar one of higher specification. ON CONDITION THAT:
The buyer returns it to the seller from whom it was bought, freight paid.
The product has been bought by the user i.e. a receipt/sales invoice is produced as proof of purchase.
The product has not been misused or handled carelessly, installed in anyway contrary to the installation
instructions, or installed in any unusually exposed or harsh environmental conditions.
This guarantee excludes liability for discolouration of paint or plastic, or any user replaceable parts. It does
not confer any rights other than those expressly set out above and does not cover any claims for
consequential loss or damage.
Our Goods come with guarantees that cannot be excluded under the Australian and New Zealand
Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the Goods repaired or replaced if
the Goods fail to be of acceptable quality and the failure does not amount to a major failure.
PUB1392 2104
Distributed in Australia by Ventair Pty Ltd.
4 Capital Place, Carrum Downs, 3201 VIC, AUSTRALIA.
Technical Support: 1300 665 926-
e: [e-mail] | www.ventair.com.au | www.simx.com.au
Distributed in New Zealand by Simx Ltd
Ph: [phone] | Technical Support Ph: [phone]
e: [email protected] | www.simx.co.nz
Specifications are subject to change without notice