NOUVOLED SOLAR PRO 200 CC User manual

SOLAR PRO 200 CC
USER Manual
200W RGBW
LED PROFILE LIGHT

Important note: to use lamps correctly, please read all
the terms of this instruction. Please keep the instruction
book in case you need it.
1 before use
1.1 the crates
Thank you for using this company's products, please read this instruction
manual carefully and carefully and keep it for reference. This specification
contains important information about the installation and use of large power
LED lights. Please follow these instructions carefully when installing and
using.
When receiving the product, please check that the product is damaged by
shipment.
1.2Product introduction
This 300W LED PROFILE LIGHT, which is made from cast-aluminum shell,
is beautiful, efficient and efficient, and is suitable for indoor use.
Products strictly according to CE standard design production, in line with
the international standard DMX512 protocol, as well as a single control,
also can use spreading into each other, suitable for large-scale theatrical
performances, theaters, studios, and other places to use.
1.3 product features
1.3.1 has the function of smooth adjustment, no flicker, no flicker of the
dimmer process, the adjustment speed can be adjusted by push rod.
1.3.2 The built-in temperature sensor automatically adjusts the light
amount according to the temperature to prevent the lamp from overheating.
1.3.3 has power and DMX512 signal light, which can be monitored at work
condition.

1.3.4 digital tube pure digital display.
1.3.5The buttons and the digital tube display can be inverted.
1.3.6Both the power line and the signal line are connected by hand.
1.3.7 USES a reflective cup to project a uniform flare.
Product general performance:
* Adjust 0 to 100%
* Stroboscopic
* self-walking program
* The protection level IP25
1.4 specifications
1.5Technical parameters:
External working voltage: ac100-240v, 50/60hz,
Maximum power: 200W
Beam Angle:26 degrees
The number of colors of various colors: 4
Using the environment temperature range: 15 ℃and 40 ℃
1.6 safety warning
Important note:
The manufacturer will not be responsible for any accidents and losses
caused by any unauthorized use and unauthorized alteration of the
equipment.
Special attention should be paid to the voltage of the power supply to
ensure that the voltage range is within the voltage range of the technical
parameter marker (100v-240v). Due to many rural areas of voltage
fluctuation range is too big, be sure to connect a power supply voltage
regulator, and then connect the lamps and lanterns, the lamps and lanterns
may be burned or make lamps and lanterns can't work.

Pieces do not use other electrical power cord and the lamp power supply
input/output connector line together, also do not put other appliances
DMX512 signal with this light DMX512 signal input/output connector lines
connected together.
To ensure the safety of the power supply, please use the quality electrical
outlet or cut the plug directly.
It is not recommended to use this lamp in direct sun exposure to avoid
overheating during work.
2 the installation
2.1 device
If the lamp is used as a lamp or top light, please put the lamp on the
hanging arm of the lamp, screw tight. Then hang the lights on the truss.
Adjust the position Angle of the light beam azimuth, and tighten the handle
screw. If the lamp as a row of lights or footlights to use, as long as the
two-hanging arm off a certain Angle, sit here as a scaffold, and then adjust
the lamps and lanterns and the Angle between the hanging arm, use light
meets the requirements of elevation, then tighten the handle screw.
2.2 the power connection
This product USES the input output power line of 1.5 square mm copper
core wire, plug is 2 core 10A pair. When the power cord is in series, no
more than 16 lights will be used when using 220V ac power.
Use this product DMX512 signal input and output don't more than 16 lamp,
street line connection in DMX controller with light or light with the light
signal lines, more than 100 meters, must increase the level of signal
amplifier.
Project distribution installation
In adopting the company lamps and lanterns, if adopt the three-phase
five-wire system, the zero line should be on each phase
This is the uniform output from the box, not a single zero.

3Operating method
3.1 Display and key operation part:
Operation instruction: under the main menu, press the up and
down key to select different function menus. After selecting
different function menus, press the "ok" key to enter the
corresponding drop-down menu function. In the drop-down menu,
press the "increase" or "decrease" key to modify its parameter
value. Press ok to return to the main menu.
3.2color screen display window comparison
table
no
display
1
DMX-Add 001
2
Key-AD
J
Red
0--255
Green
0--255
Blue
0--255
White
0--255

dodge
0--255
3
Auto
-ADJ
Auto
1--2
speed
0--100
4
Screen
Rotate
ON/OFF
3.3Comparison table of background display
window in English
no
display
The initial value
1
Fan temp
20--70
40
2
Low power temp
35--90
45
3
Protect temp
ON/OFF
OPEN
4
Red Current
20－255
235
5
Green Current
20－255
235
6
Blue Current
20--255
235
7
White Current
20--255
235
8
Language
EN
CHINESE
9
Screen saver
ON/OFF
OPNE
3.4DMX512 Eight-channel specification
NO
function
instructi
ons
Channel
1
dimming
R、G、B、W Total dimming, linear
dimming, from dark to light
Channel
2
Total
stroboscopic
R、G、B、W Total stroboscopic,
from slow to fast
Channel
3
R dimming
R dimming, linear dimming,
from dark to light

Channel
4
G dimming
G dimming, linear dimming,
from dark to light
Channel
5
B dimming
B dimming, linear dimming,
from dark to light
Channel
6
W dimming
W dimming, linear dimming,
from dark to light
Channel
7
Feature
selection
0—50 ：DMX 8Channel
control；51－－100：jump；
101—150 ：The gradient ；
151—200 ：Pulse variable ；
201—255：Voice control
Channel
8
Function of
speed
Function speed, from slow to
fast
3.5．RDM instructions:
NO
function
instructions
1
Feedback
(address code)
Free to change
2
Feedback
(equipment
temperature)
Cannot be changed
After power on, switch on the console power. When
DMX512 console signal is not received, Dmx indicator
light will not be on. When receiving the DMX512 control
station signal, the Dmx indicator light will be on to
control the signal of the controlled station.
In the address code state, after the multi-machine
connection, if there is no access console, the
master-slave online function can be realized to operate
one of the devices, the rest of the devices in the address
state follow the host to run the program synchronously,

the master-slave online must cut off the DMX512 signal.