Event Lighting PAR4X12B2 User manual

PAR4X12B2
4x12W RGBWAUV LED PAR with Wireless DMX & IR Remote
USER MANUAL
For your safety, please read this user manual carefully before use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version 1.0 (September 2023)

www.event-lighting.com.au
2
Warning
 Do not open this device, there are no user serviceable parts inside. Risk of electric shock.
 Do not look directly at the light source from close range.
 Avoid contact with the unit during operation, as the housing may become hot. Allow the fixture to
cool for at least 15 minutes after turning off before touching.
 Install this device in a location with adequate ventilation, at least 50cm from adjacent surfaces.
 Do not operate this device, or connect this device to power, within 50cm of any flammable
material.
 Use a safety chain when mounting this device overhead.
 Do not operate this device outdoors where excessive dust, heat, water, or humidity may affect it.
 This fixture was designed for indoor use only, do not expose this unit to rain or use nearwater..
 Do not operate this device if the housing, lenses, or cables appear damaged.
 Do not connect this device to a dimmer or rheostat.
 Do not operate this device at temperatures higher than 40°C (104°F).
 Only connect this device to a grounded and protected circuit.
 Only use the hanging bracket to carry this device.
 Stop using this device immediately if a serious operating problem becomes apparent.
Product Installation
PAR4X12B2 can be mounted in many orientations, provided each individual device is secured by
the use of the correct mounting bracket. Use a safety chain when mounting PAR9X120B overhead
Lux Chart
Distance (m) 1 2
3 4 5
Diameter (m) 0 0.44 0 0.89
01.33 01.77 0 2.22
Red
883 263 116 73 52
Green 1356 389
171
106
73
Blue
1610 450 202 122 83
White
1722 513 224 138 94
Amber 532
151
72 46 36
UV
492 156 72
46 35
Full
5980 1590 732 440 292

www.event-lighting.com.au
3
Control Operation
MENU Main Menu Function Select I Exit Submenu
UP
Select Previous Menu / Parameter Increase by
degrees
DOWN Choose the next menu / parameter decrease by
degrees
ENTER Confirm the selected function / Enter the next
menu
Set DMX
Set DMX Address Code
1. Press User Settings end Enter until "DMX512" is highlighted then press Enter.
2. The screen will display "Address Set: 001". Press Up or Down to change.
3. Press Enter to save , and press Menu to exit .

www.event-lighting.com.au
4
Menu Description
Menu
Level1 Level2 Level3
Static Color Dimming
RED 0-255
GREEN 0-255
BLUE 0-255
WHITE 0-255
AMBER 0-255
PURPLE 0-255
STROBE 0-20
Choose
Pattern
Macro 1-32
(Speed)
Show "AUTO" 0-20
"FADE" 0-20
"SNAP" 0-20
"R-STRO" 0-20
"G-STRO" 0-20
"B-STRO" 0-20
"A-STRO" 0-20
Sound "SOUND1" 0-100
"SOUND2" 0-100
"SOUND3" 0-100
Channel 6/10
DMX512 001-512 Set OMX address
W-DMX RCVD Wireless receive
DMX512 Use OMX cable
User
Settings
Follow Syn Transmits Master/need all lamp pair by
Transmitter first.
White Balance (Color) (Brightness)
RED 127-255
GREEN 127-255
BLUE 127-255
WHITE 127-255
AMBER 127-255
PURPLE 127-255
Show Battery Icon YES/NO
Display Sleep Open/5/10/15Sec
Autolock YES/NO
Infrared Setting ON/OFF
Wireless Setting ON/OFF
System
Settings
Factory Reset Password: button UP+DOWN+UP+DOWN+ENTER
Informations VER Information of the version

www.event-lighting.com.au
5
DMX Chart
6-Channel Mode
Channel Value Function Description
1
0-255 Red Intensity Red 0-100%
2
0-255 Green Intensity Green 0-100%
3
0-255 Blue Intensity Blue 0-100%
4
0-255 White Intensity White 0-100%
5
0-255 Amber Intensity Amber 0-100%
6
0-255 UV Intensity UV 0-100%
10-Channel Mode
Channel
Value Function
1
0-255 Master Dimmer
0-9 2
10-255
Strobe
3
0-255 Red Intensity
4
0-255 Green Intensity
5
0-255 Blue Intensity
6
0-255 White Intensity
7
0-255 Amber Intensity
8
0-255 UV Intensity
0-9 No function
10-29
Colour choose, CH10 choose colour
30-49
Jump variable effect : CH10 control the speed
50-69
gradual variable effect
.:
CH10 control the speed
70-89
mutation effect: CH10 control the speed
90-109 Red+ strobe:CH10 control the speed
110-129 Green + strobe:CH10 control the speed
130-149 Blue+ strobe:CH10 control the speed
150-169 Amber+ strobe:CH10 control the speed
170-189 UV+ strobe:CH10 control the speed
9
190-255 Sounds control
10
0-255
This channel's function are depending on the value of
CH9: When the value is 10-29, then the function is
colours choose.
When the value is 30-189, then the function is speed control:
O is the lowest,255 is the fastest.

www.event-lighting.com.au
6
In order to use the IR Remote, If a OMX signal is received, PAR4X12B2 will
prioritise the OMX signal and ignore the IR Remote. Use On/Off to turn
PAR4X12B2 on or off. Press R/G/B/W/A/U to light up the LEDs in red, green,
blue, white, amber or UV respectively,press + or - to adjust R/G/B/W/A/U.
There is also a selection of preset colours underneath the R/G/B/W/A/U
buttons, known as the D Area. Press a button in the D Area(0-9) to select
that colour. When choose the Auto or Strobe, press+ to increase thespeed
and - to decrease the speed. When choose the Sound, press + to increase
the sensitivity and - to decrease the sensitivity.
Technical Specifications
Photometrics
Light Source: 4x 6-in-1 RGBWAU 12 W LEDs Beam Angle: 20°
Output: 5980 lux on @1M, 1590 lux on @2M,RGBWAU Full on PWM: 16,000 Hz
LED Lifespan: 50,000 hours
Effects:
Dimming: 0~100% Strobe: 0~20 Hz
Operation Modes: Wireless OMX, manual, auto, sound active, master/slave, IR Remote Control:
Wireless OMX, IR OMX Channels: 6 / 10
Display: 4-button & 4-digit LCD display control panel
Power:
Input Voltage: 100~240V AC, 50/60 Hz Power Consumption: 48W
Connection: Powercon in/out socket, 5pin XLR in/out Battery:
Approx. 4 hours Full Colour Approx. 15 hours Single Colour
Housing:
Materials: Die-cast Aluminium, matte black finish Finishing: Matte black
Cooling: Fanless IP rating: IP20
Net Weight: 2.4 kg
Overall Size: 147 x 136 x 200 mm
Warranty
Please refer to your local dealer or contact Event Lighting.