Saxby Lighting Odyssey Spike Manual

When changing a bulb, always switch off at the mains and allow the bulb to cool before handling. Dispose of
used bulbs carefully. Use a soft cloth to handle bulbs, avoid directly touching the bulbs as this will shorten their life. Do not
exceed the wattage stated or use a different shape bulb from that indicated on the fitting.
Check with your retailer re bulb dimming capability before purchasing replacement bulbs.
Bulb type - 7W LED GU10
1. Unscrew the bezel
2. Remove the old bulb by turning anti-clockwise.
3. Insert new bulb.
4. Replace the bezel ensuring that it is tightly secured.
Instruction leaflet
Odyssey Spike
ST5011
www.saxbylighting.com
For your safety, always switch off the supply before cleaning.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
Saxby Lighting. BH23 3PE
Do not use solvents or abrasive cleaners as these could
damage the finish.
In normal circumstances, stainless steel is very resistant to
corrosion. It does however require maintenance to preserve
the high quality appearance. Wash the product with warm
soapy water, removing all surface deposits. Rinse with clear
water and with a soft cloth, wipe dry.
In some cases, surface corrosion may arise after installation.
This is normally caused by tiny iron particles left behind
after the brushing process when finishing.
Wash and dry as detailed above. Then with a soft cloth
soaked with a protective oil, wipe all over.
However if the product is subject to extreme environmental
conditions such as marine locations, industrial pollution
and acid rain these maintenance procedures should be
carried out around four times a year. For severe corrosion,
non-abrasive cream cleaners or proprietary stainless steel
cleaners should be used to remove the corrosion. Wash and
dry as detailed above. Then with a soft cloth soaked with a
protective oil, wipe all over.
The shade must be replaced immediately should the shade become cracked or damaged. This fitting
must not be used without the shade in place.
Iss.4 080820182018
Fitting/replacing bulbs (Max. 3.5W LED GU10)
Care and Cleaning
3.5W LED
GU10

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before
commencing any work.
This unit must be fitted by a competent and qualified
electrician.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting. Ensure other
persons cannot restore the electrical supply without
your knowledge. If you are in any doubt, please consult a
qualified electrician.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the
connections.
Always use the correct type and wattage bulb. Never
exceed the wattage stated.
This product is suitable for dimming.
When changing a bulb, always switch off at the mains and
allow the old bulb to cool down before handling. Dispose
of used bulbs carefully and responsibly.
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling
advice.
This product is rated at IP65.
This product is suitable for location in or near a marine
or sea environment. Please pay particular attention to the
care and cleaning instructions to minimise any effects
from a corrosive atmosphere.
Please note: entire unit gets hot whilst on for a period of
time.
This light fitting should be connected to a 30mA RCD.
This product may require the use of a outdoor rated
connector block.
If the external flexible cable or cord of this lamp is
damaged the lamp must be returned to the service agent
for repair.
Specification
Voltage: 240V 50Hz a.c.
Lamp: 1 x Max. 7W LED GU10
IP rating: 65
Layout
Wiring
• Decideonthepositionoftheluminaire.Dependingon
the location, an approved outdoor rated plug and socket
may be required. Alternatively an approved outdoor
rated external terminal block may be used.
• Avoidlocatinganycablesinpositionsthatwouldcause
a hazard. Position cables and connector block away
from areas where they may be at risk from being cut,
trapped or damaged.
• Cablesthataretobeinwallsandconcealed
underground must be protected using suitable conduit
or plastic trunking.
• Ensurethatthegroundissuitableforpushingthespike
into, and can support the luminaire. Do not install in
very wet or boggy areas.
Plug Wiring
• Theappliancemustbeconnectedtoa240voltsAC
supply.
• Theappliancecanbefittedtoarewireable3pin
plug fitted with a 3 amp fuse. Should the fuse require
replacement, it must be replaced with a fuse rated at 3
amp and approved to BS1362.
•Thewiresinthemainsleadonthisapplianceare
coloured in accordance with the following code:
Blue – Neutral
Green / Yellow - Earth
Brown – Live
• You have correctly identified the wires
• The connections are tight
• No loose strands have been left out of the connection
block.
• Ensure that all cord grips are tightly secured.
• Ensure that all seals are re-fitted correctly.
If not fitting to a plug then the product must be wired to a
IP44 rated terminal block.
Having correctly identified the wiring from your existing light
fitting, connect to the approved outdoor rated
external terminal block in the following way:
Wiring
Check that...
Commissioning
• Ensurethatthegroundissuitableforpushingthespike
into, and can support the luminaire. Do not install in very
wet or boggy areas. Push the spike into the ground.
• Replacefuseorcircuitbreakerandswitchon.Yourlight
is now ready for use.
Spotlights give a concentrated beam of light and must not be positioned any closer than 0.5M (50cm) to
the illuminated surface.