SINTERIT POWDER SIEVE User manual

Sinterit POWDER SIEVE
USER MANUAL
Read the instruction manual before using the device.
Version 7/2020

2 | Sinterit POWDER SIEVE User Manual
Table of contents
1. Marking text conventions used in a document............................................................................................................... 3
2. Contents of the Sinterit POWDER SIEVE pack ................................................................................................................ 4
3. Sinterit POWDER SIEVE..................................................................................................................................................... 5
A. Description .................................................................................................................................................................... 5
B. Specication.................................................................................................................................................................. 6
4. Important safeguards and warnings ................................................................................................................................ 7
A. Environment and place of installation ......................................................................................................................... 7
B. General safety rules ........................................................................................................................................................ 7
C. Personal protection ........................................................................................................................................................ 8
D. Power supply ................................................................................................................................................................... 8
E. Safety during sieving, repair and maintenance ............................................................................................................. 9
F. Working with powders ................................................................................................................................................... 10
G. Scrapping ...................................................................................................................................................................... 10
5. Initial startup of the Sinterit POWDER SIEVE after delivery ............................................................................................ 11
6. Sieving process.................................................................................................................................................................. 12
7. Maintenance of the Sinterit POWDER SIEVE ................................................................................................................... 14
A. Periodical maintenance ................................................................................................................................................ 14
B. Exchanging/cleaning Removeable Metal Sieve ......................................................................................................... 15
8. General legal information.................................................................................................................................................. 16
9. Disclaimer............................................................................................................................................................................. 16
10. Trademarks ........................................................................................................................................................................ 16
11. Terms of warranty.............................................................................................................................................................. 17
12. Technical support .............................................................................................................................................................. 17
13. Our Powders and dedicated Removable Metal Sieves.................................................................................................... 18
14. Life of the Powder............................................................................................................................................................. 18
15. Compatibile solution for work with Powders from Sinterit............................................................................................. 18

Sinterit POWDER SIEVE User Manual | 3
1. Marking text conventions used in a document
Listed below are descriptions of symbols used on the device. They constitute a warning or convey the information to
protect the user, other individuals or surrounding objects and ensure the correct and safe use of the device.
WARNING!
An inevitably dangerous situation which can result in serious injury or even death. Initiation,
the omission of a specic procedure or inattention can cause severe physical injury to the
user.
ATTENTION!
Initiation or omission of a specic procedure can cause physical damage to the equipment
or the user.
ATTENTION!
Risk of electric shock which can be fatal or cause severe burns. An inevitably dangerous
situation which can result in serious injury or even death, if not mitigated. Before working
with any equipment, you should be aware of the dangers associated with the ow of
electric current, and become familiar with the standard procedures to prevent accidents.
CAUTION!
Beware of moving parts which can crush hands.
WARNING!
Risk of re and explosion!
Avoid re! Powder dust is ammable.
STOP!
Action prohibited.
ATTENTION!
It is necessary to wear protective gloves and a face mask. Mandatory action when working
with powder.
ATTENTION!
It is necessary to wear antistatic clothes and shoes. Mandatory action when working with
powder.
ATTENTION!
It is necessary to wash hands after each use of the Sandblaster XL.
IMPORTANT!
Information essential to correctly perform a specic task.
IMPORTANT!
You must read the instructions before taking action.

4 | Sinterit POWDER SIEVE User Manual
2. Contents of the Sinterit POWDER SIEVE pack
Box no. 1
• The Sinterit POWDER SIEVE,
• The additional equipment.
Box no. 2
• Spare Metal Container with Lid.
Sinterit POWDER SIEVE
USER MANUAL
Read the instruction manual before using the device.
Version 7/2020
A
B
D
C
Image 1. Accessories for the Sinterit POWDER SIEVE (box no. 1).
A.Metal container (12 L) / B.Power supply / C.Allen key Hex 3 mm (for Removeable Metal Sieve) /
D.Sinterit POWDER SIEVE User manual
E
F
Image 2. Accessories for the Sinterit POWDER SIEVE (box no.2).
E.Spare Metal container (12 L) / F.Lid for the Metal container

Sinterit POWDER SIEVE User Manual | 5
3. Sinterit POWDER SIEVE
A. DESCRIPTION
2
DONOT REMOVE THIS LABEL!
Manufacurer:
SINTERITSp.z o.o.
ul. Nad Drwiną 10 bud. B3, 30-741 Kraków, Poland
www.sinterit.com
Contact: [phone], [email protected]
Name:
SINTERIT POWDER
SIEVE
Serialnumber:
042020140070
Manufactured: Made in: EU, POLAND
IP30
Class 3
Machinetype: HORIZONTAL VIBRATING SIEVING MACHINE
Dimensions: 360 x 340 x 600 [mm] 14.7 x 13.4 x 126.6 [in]
Totalweight: 22.5 [kg] 49.6 [lb]
Ratedvoltage 12 V [DC]
Powerconsumption 24 [W] Sockets
polarity
ACadapter 12 [V] ~ 5.0 A
Rotatingparts speed 3000 [rpm]
WARNING! Read and understand operator’s manual and all other safety instructions before using this machi-
ne. Failure to follow operating instructions could result in serious injury.
1
4
3
7 77 7
56
8 9
Image 3. View of the Sinterit POWDER SIEVE front and back.
1.Lid / 2.Viewing window / 3.Lid handle / 4.Power button / 5.Door / 6.Door handle /
7.Adjustable mounting feet (4 pcs.) / 8.Fuse / 9.Power socket
12
13
14
15
2
11
10 10
Image 4. View of the Sinterit POWDER SIEVE top chamber.
10.Lid’s magnetic holders / 11.Removeable Metal Sieve
Image 5. View of the Sinterit POWDER SIEVE front chamber.
12.Flange / 13.Flange adapter / 14.Door magnetic holder /
15.Stabilising plate

6 | Sinterit POWDER SIEVE User Manual
B. SPECIFICATION
GENERAL
Category Horizontal vibrating sieving machine
Type Automatic
PACKAGING
Size of package 610 x 360 x 370 [mm] (24.2 x 14.1 x 14.5 [in])
Package weight 25 [kg] (55.1 [lbs])
Package contents 2 boxes: Sinterit POWDER SIEVE + set of accessories + Manual
POWER
Voltage 12 [V] DC
Power 24 [W]
AC adapter 12 [V] ~ 5.0 [A]
TECHNICAL DATA
Dimensions 600 x 340 x 360 [mm] (23.6 x 13.4 x 14.2 [in])
Total weight 22,5 [kg] (49.6 [lbs])
Powder capacit 5 [L]
Rotating parts speed 3000 [rpm]
SAFETY
Certicates CE, FCC

Sinterit POWDER SIEVE User Manual | 7
4. Important safeguards and warnings
IMPORTANT!
• To ensure the safe use of the Sinterit POWDER SIEVE product, please read and follow the
instructions below.
• Keep this manual for future use. Also, be sure to follow all warnings and instructions marked
on the product.
IMPORTANT!
Only trained and qualied personnel should install, replace or service the equipment and the
device should be installed in accordance with these instructions.
A. ENVIRONMENT AND PLACE OF INSTALLATION
WARNING!
• The powder sieve must be positioned protected against atmospheric agents (rain, hail,
snow, fog, dusts in suspension, etc.) with an environmental running temperature between
5°C and 45°C and relative humidity not above 70%.
• Do not place or store the product in places subject to shocks, vibrations.
• The work environment must be clean, well-enough lit and devoid of the explosive atmosphere
(in areas with high dust).
• The product should be placed on a at, stable surface that extends beyond all edges of the
product. The product will not work properly if it is set at an angle.
WARNING!
• Fire and explosion hazard! The device must not be operated in a corrosive or
explosive environment.
• Avoid using the device near water, close to open ames or sources of heat.
• Do not place or store the product near inammable and volatile substances,
concentrated acids or corrosive vapours.
• Avoid prolonged contact with solvents and inhaling their vapours.
B. GENERAL SAFETY RULES
WARNING!
• Only adults should use powder sieve.
• When using the machine, mind other people, especially children.
• Climbing on the powder sieve is forbidden.
ATTENTION!
• Risk of crushing upper limbs while closing the Lid 1from the top chamber.
• Never place hands between the Door 5and front chamber while locking.
• Do not put hands between Flange adapter 13 and Metal container Aduring
assembly.
ATTENTION!
• Check the device previous to each use for damaged and/or defect parts.
• In case of a defect, or when the machine does not function properly, rst have it repaired by
a specialized person/company.

8 | Sinterit POWDER SIEVE User Manual
C. PERSONAL PROTECTION
ATTENTION!
• The operator must always wear antistatic clothes and shoes.
• The oor of the area must be antistatic.
ATTENTION!
• Prevent breathing in dust at all times, wear respiratory protection at all times.
When one enters the room where the powder sieve stands with regard to
particulate matter that is released during the sieving.
• Breathing in particulate matter causes serious lung problems.
• At all times wear Protective Dust Mask and Protective Glasses when opening
the Lid/Door after using the machine (e.g. you can use the “PERSONAL
PROTECTION” set included with Lisa printers).
ATTENTION!
After each use of the Sinterit POWDER SIEVE, wash your hands.
D. POWER SUPPLY
WARNING!
• Before plugging in, make sure the power voltage and frequency are those
shown on the machine safety plate.
• Use only the power supply that meets the power and safety conditions.
• Do not use cables/supplies from other devices. Using the power cables from
other devices or connecting the power supply supplied with the product to
other devices may cause a re or electric shock.
• When an extension cord is used for the power supply of the product, make
sure that the total power consumption of all devices connected to it does
not exceed the extension cord’s limit. Also, make sure that the total current
drawn by connected equipment does not exceed the ampere rating for AC
wall outlet.
• The device should be placed near a wall outlet, which can be easily unplugged.
WARNING!
• When connecting/disconnecting the plug to/from the power source always
hold the cover, not the cord.
• Pay special attention to the fact that the power cables are not bent at the
points of connection of the sieve.
• During use, mind the power supply cables and avoid crushing, pulling, twisted
or rubbed these.
• Periodically check the mains power cable to ensure it is not damaged.
• In the event of the cable, plugs or couplings being replaced, make sure these
are protected against water spray and check mechanical strength.
STOP!
• Never pull the machine by means of the power cable.
• In the event of the cable being damaged, the machine must not be used.
• Do not place objects on the power cables.
• Do not place power cables in a path where people will have to walk or run.

Sinterit POWDER SIEVE User Manual | 9
STOP!
• Never touch electric wires, switches, buttons, etc. with wet hands.
• Do not spill liquid on the product.
• Do not put any containers on the equipment, in particular containing water.
• Do not block or cover the vents and openings in the product.
• Do not touch live parts.
WARNING!
• Disconnect the plug whenever it is planned to shift/transfer the machine.
• If the device is not used for a long time (e.g. vacation), unplug the power
supply from the socket.
E. SAFETY DURING SIEVING, REPAIR AND MAINTENANCE
WARNING!
In the following situations, unplug the product from the power supply and contact qualied
service personnel:
• the power cord or plug is damaged;
• some liquid got into the product;
• the product has been dropped or the case damaged;
• the product does not operate properly or clear changes in eciency have been observed.
Failure to heed these instructions may cause damage to materials and/or injures!
STOP!
• Never disassemble, modify or repair the power supply, plug or devices inside the sieve,
except as described in the product’s manual.
• Do not adjust controls that are not described in the manual.
WARNING!
• All maintenance operations must be executed in a non-classied atmosphere.
• Only skilled persons should carry out repairs.
• Read the operator’s and maintenance manual carefully before using the cleaner or doing any
maintenance jobs.
• During cleaning operations, maintenance jobs or when changing parts, the Power button
must be off and the machine must be unplugged by removing the cable from the socket.
• During maintenance jobs, ax a notice to the appliance indicating „MACHINE BEING
SERVICED, DO NOT START”.

10 | Sinterit POWDER SIEVE User Manual
F. WORKING WITH POWDERS
ATTENTION!
When working with the polyamide powder or other designated printer powder for
the Sinterit POWDER SIEVE always wear protective kit: glasses, gloves, dust mask
(e.g. you can use the “PERSONAL PROTECTION” set included with Lisa printers).
ATTENTION!
• When working with a polyamide (PA) powder, avoid inhalation or swallowing and contact
with skin and eyes.
• If the PA powder is inhaled, move to a place with fresh air and gargle thoroughly with plenty
of water. If coughing develops, contact a physician.
• In case of swallowing PA powder, rinse your mouth with water and drink 1-3 glasses of water
to dilute stomach contents. Contact your doctor.
• If the PA powder gets in your eyes, rinse them thoroughly with water. In case of persisting
eye irritation, contact a physician.
• When the PA powder gets in contact with your skin, wash it with soap and water.
ATTENTION!
• Polyamide powder should be stored in tightly closed containers, in a room at room
temperature and low humidity.
• The powder should be stored out of reach of children and pets.
• If the device is not used for a long time, the powder should be stored in a sealed package.
WARNING!
• Fire and explosion hazard!
• Do not attempt to burn/melt polyamide powder. The resulting sparks and hot
mass, the powder is converted into can cause severe burns.
• Keep the polyamide powder away from re.
STOP!
Do not dispose to municipal waste!
The used polyamide powder should be stored in sealed containers and disposed
of in accordance with local policy of waste plastic material.
G. SCRAPPING
IMPORTANT!
In case of scrapping, all the component parts of the powder sieve will have to be
disposed of through adequate disposal channels in accordance with applicable
legislation. Before scrapping, all plastic and rubber parts will have to be separated
from the electrical material. Parts made of plastic, aluminium and steel only may
be recycled if collected by special centres.

Sinterit POWDER SIEVE User Manual | 11
5. Initial startup of the Sinterit POWDER SIEVE after delivery
1. Carefully pull the powder sieve out of box 1 and remove the transport protections.
2. Place on a stable and hard surface (it is recommended for it to be the target location of the powder sieve).
ATTENTION!
Before installing the Sinterit POWDER SIEVE, carefully check if it hasn’t been damaged during
transport.
CAUTION!
• The Lid 1 is heavy!
• The danger of crushing upper limbs when lowering the Lid.
IMPORTANT!
When opening the Lid or Door, hold it by the handles 3, 6, as they open violently.
3. Open the Lid 1from the top chamber and remove the transport protections.
4. Open the Door 5and remove the Metal container Aby pulling the Flange 12 up.
5. Remove the Power supply Bfrom the box (should be inside a Metal container).
6. Put the Metal container back under the Flange. Watch your ngers!
7. Check the levelling of the powder sieve. In case of problems, correct with Adjustable mounting feet 7.
8. Connect the Power supply Bto the Power socket 9and screw the Flange connector B’ (correct connection –
drawing on the safety plate) (Image 6). Next, connect to the power source.
9
DO NOT REMOVE THIS LABEL!
Manufacurer:
SINTERIT Sp.z o.o.
ul. Nad Drwiną 10 bud. B3, 30-741 Kraków, Poland
www.sinterit.com
Contact: [phone], [email protected]
Name:
SINTERIT POWDER
SIEVE
Serial number:
042020140070
Manufactured: Made in: EU, POLAND
IP30
Class 3
Machine type: HORIZONTAL VIBRATING SIEVING MACHINE
Dimensions: 360 x 340 x 600 [mm] 14.7 x 13.4 x 126.6 [in]
Total weight: 22.5 [kg] 49.6 [lb]
Rated voltage 12 V [DC]
Power consumption 24 [W] Sockets
polarity
AC adapter 12 [V] ~ 5.0 A
Rotating parts speed 3000 [rpm]
WARNING! Read and understand operator’s manual and all other safety instructions before using this machi-
ne. Failure to follow operating instructions could result in serious injury.
B’
Image 6. Correct connection of the Power supply to the powder sieve.

12 | Sinterit POWDER SIEVE User Manual
6. Sieving process
ATTENTION!
• Before starting any job with the powders, always wear Protective Glasses, Protective Dust
mask, and Protective Gloves.
• You can use the “PERSONAL PROTECTION” set included with Sinterit Lisa printers.
CAUTION!
• The Lid 1 is heavy!
• The danger of crushing upper limbs when lowering the Lid or closing the Door.
1. Open the Door 6and check that the Metal container A is properly and tightly tted under the Flange 12 . If necessary,
install a new one.
2. Close the Door by pressing it gently.
3. Open the Lid, holding the Door’s housing with your other hand.
4. Gently pour the powder from the Metal container (or from Lisa/Lisa PRO printer) into the Removeable Metal Sieve 11.
5. Clean the space around the Removeable Metal Sieve (e.g. using a brush). Pay special attention to the endstops 16
near the Lid hinges (Image 7).
16 16
Image 7. Position of the Lid’s endstops.
6. Holding the Lid handle, close it.
7. Press the Power button 4 quickly. The device should start working.
8. The powder sieve will work for about 18 minutes, then it will automatically switch off.
9. If the whole powder is already sieved, you can stop the powder sieve faster manually, by pressing for 3 sec the Power
button.

Sinterit POWDER SIEVE User Manual | 13
SIEVING PROCESS
18min
10 l
10 l
OF RECYCLED
POWDER
10 l
POWDER REFRESHING
18min
10 l
PRINT
READY
POWDER
10 l
FRESH
POWDER
USED
POWDER
POWDER
REFRESHIN
Image 8. Sieving and refreshing process.
IMPORTANT!
• You can watch the sieving progress through the Lid Viewing window 2.
• The Sinterit Powder Sieve will stop working if you open the Lid or Door.
• If you press and hold the Power button, the machine will not start working. To run the device,
please press and release the Power button immediately.

14 | Sinterit POWDER SIEVE User Manual
7. Maintenance of the Sinterit POWDER SIEVE
This section describes the control and special maintenance operations crucial for keeping the Sinterit POWDER SIEVE
in perfect working condition
WARNING!
Before replacing the accessories or beginning the assembly, repair, transport,
or any form of maintenance, disconnect the Sinterit POWDER SIEVE from the
power source.
ATTENTION!
Before starting any maintenance or cleaning job, always wear adequate protective clothing,
eyewear, face mask, and/or gloves according to the type of job to be done.
CAUTION!
• The Lid 1 is heavy!
• The danger of crushing upper limbs when lowering the Lid or closing the Door.
IMPORTANT!
Before starting any maintenance work, read and understand this user manual.
A. PERIODICAL MAINTENANCE
• After each use of the powder sieve, clean it with compressed air or with a Sinterit ATEX Vacuum Cleaner (we
recommended). Clean both chamber (top and front).
• Check the Lid endstops 16 and Door endstop 17 . Clean them off from the powder and dust. Endstops work properly
if, while the powder sieve is running, the user opens the Door or Lid and the motor automatically switches off.
16 16
17
Image 9. Position of the Lid’s endstops and Door’s endstop.

Sinterit POWDER SIEVE User Manual | 15
B. EXCHANGING/CLEANING REMOVEABLE METAL SIEVE
• In the Sinterit POWDER SIEVE, a Replaceable Metal Sieve is installed by default for powder PA12 SMOOTH. For the
other powders available in the Sinterit offer there are dedicated sieves suitable for.
• It is higly recommended to clean the vibration module underneath the Removeable Metal Sieve regularly.
1. Disconnect the powder sieve from the power supply.
2. Holding the Lid handle, open it.
3. Vacuum/clean the top chamber (with Removeable Metal Sieve 11 ) if necessary.
4. Unscrew 6 Allen screws around the Removeable Metal Sieve. Use the supplied Allen key C(Image 10).
Image 10. Position of the 6 Allen screws around Removeable Metal Sieve.
5. Remove the Removeable Metal Sieve.
6. Install a new one, or clean the vibration module and install the current Removeable Metal Sieve. Remember to tighten
the Allen screws rmly.
ATTENTION!
Any other problems not described in this manual should be reported to Sinterit Support by
contacting through:
• email: [email protected]
• WWW: sinterit.com/support-page/
• phone: [phone]

16 | Sinterit POWDER SIEVE User Manual
8. General legal information
Where this manual refers to Sinterit or the Company, this means Sinterit sp. z o.o. with its legal seat in Krakow, registered
by the District Court for Kraków-Śródmieście in Krakow, XI Commercial Division of the National Court Register under
number: 535095, NIP (tax number): 6793106416, with the share capital for a date of publication of this manual of PLN
102,050 (say: one hundred and two thousand and fty).
This document contains material protected under copyright and industrial property laws. This means that the document
may not be, including but not limited to, reproduced or modied without the consent of Sinterit.
This manual serves to assist you in the correct use of the device, perform basic maintenance and, if necessary, to solve
simple problems, allowing you to maintain the device in a good condition.
This manual contains content exclusively for the provision of information and the use by individuals professionally
trained and engaged in the operation and maintenance of the equipment described below.
The information contained in this document is intended for use only with the product called Sinterit POWDER SIEVE.
Due to the constant development of Sinterit’s products the information contained in this manual, specications and
markings are subject to change without notice.
9. Disclaimer
Sinterit is not responsible for any use of this information in relation to other products.
Sinterit is not liable for any damages, including but not limited to losses or lost prots, resulting from the use of any
materials (consumables) other than those provided to the purchaser by Sinterit.
Sinterit is not liable to the purchaser of the product or any third party for any damages, including but not limited to
losses or lost prots resulting from improper use of the product, particularly not in accordance with this manual, or
modications or repairs unauthorised by Sinterit or improper maintenance.
Although every effort has been taken to provide accurate information about the product, Sinterit assumes no responsibility
for any incorrect information or omission. Sinterit reserves the right to correct any errors and disclaims any liability in
situations resulting from these errors.
Further limitations or exclusions of Sinterit`s liability may result from the applicable laws or agreements entered into with
the purchaser of the products.
10. Trademarks
Sinterit logo is a registered trademark of the Company.

Sinterit POWDER SIEVE User Manual | 17
11. Terms of warranty
The terms of the warranty are set forth in the agreement between the buyer and the Company.
In case of a purchase made in the Sinterit online shop, the terms of the guarantee are specied in the Terms and
Conditions, subject to the acceptance of the Customer before placing an order.
In case of purchases made outside the Sinterit online store, the warranty terms may be specied in the offer, or in another
form chosen by the Company to provide the customer with relevant information before making a purchase decision.
Sinterit’s warranty does not cover including but not limited to:
• damages, abnormalities or malfunction caused by a client or any third party,
• damages, abnormalities or malfunction caused by inappropriate use, effects of force, insucient or inappropriate
maintenance, abnormal operating conditions, incorrect installation or inadequate servicing,
• damages, abnormalities or malfunction caused by dismantling, alterations, tuning or other changes of the product
by a client or any third party made without written consent of Sinterit,
• damages, abnormalities or malfunction caused by or related to use of consumables other than those being supplied
by Sinterit,
• damages, abnormalities or malfunction caused by or related to use of product against instructions/manuals or
safety regulations,
• damages or abnormalities Sinterit is not liable for, according to the applicable law,
• damages exceeding the price paid by the client,
• costs incurred by the client in connection with the conclusion of the product sale agreement as well as storage and/
or insurance of products,
• damages of property caused by the defect of the product,
• loss of prots,
• incidental, indirect, consequential damages.
The warranty does not cover any cleaning of working parts
12. Technical support
The latest information, technical support and versions of the manual are available by contacting us through:
• email: [email protected]
• www: sinterit.com/support-page/
• phone: [phone]
The list of distributors and technical support in specic countries can be found at www.sinterit.com/contact

18 | Sinterit POWDER SIEVE User Manual
13. Our Powders and dedicated Removable Metal Sieves
PA12 Smooth
PA12 Smooth
PA11 Onyx
PA11 Onyx
FLEXA Grey
FLEXA Grey
FLEXA Soft
FLEXA Bright
TPE
Metal Sieve Module PA12 SMOOTH
(default installed in the Sinterit POWDER SIEVE)
Additional Metal Sieve Module
FLEXA and TPE
Additional Metal Sieve
Module PA11 ONYX

Sinterit POWDER SIEVE User Manual | 19
14. Life of the Powder
USED
POWDER
FRESH
POWDER
PRINT
READY
POWDER
F
i
l
l
i
n
g
M
a
c
h
i
n
e
P
r
e
p
a
r
a
t
i
o
n
f
o
r
p
r
i
n
t
i
n
g
R
e
m
o
v
i
n
g
p
o
w
d
e
r
a
f
t
e
r
p
r
o
c
e
s
s
15. Compatibile solution for work with Powder from Sinterit
Sinterit Atex Vaccum CleanerSinterit Advanced Accessories
Clean & Easy Keep powder
under control
Sinterit Powder Sieve

SINTERIT Sp. z o.o.
ul. Nad Drwina 10 bud. B3, 30-741 Krakow, Poland
www.sinterit.com
Contact: [phone]