Sirius Satellite Radio SLT955 Quick start guide
INFORMAZIONI COMMERCIALI PER I CONSUMATORI
COMMERCIAL INFORMATION FOR THE CONSUMER
INFORMATIONS COMMERCIALES POUR LE CLIENT
INFORMACIONES COMERCIALES PARA EL CLIENTE
HANDELSINFORMATIONEN FÜR DEN KUNDEN
COMMERCIËLE INFORMATIES VOOR DE KLANT
ISTRUZIONI PER L’USO S-DD3
INSTRUCTIONS FOR USE S-DD3
INSTRUCTIONS POUR L’EMPLOI S-DD3
ISTRUCCIÓNES DE USO S-DD3
BEDIENUNGSANLEITUNG S-DD3
GEBRUIKSAANWIJZIGING S-DD3
IT
EN
FR
ES
DE
NL
INFORMAZIONI TECNICHE
TECHNICAL INFORMATION
INFORMATION TECHNIQUES
INFORMACIONES TÉCNICAS
TECHNISCHE INFORMATIONEN
TECHNISCHE INFORMATIES
TYPE: FSEE
2
3
4
5
6
SLT955 vagy SLT956
12
PANEL OPENING DUCTING SYSTEMS
Open the panel by pulling it from the side
where the speed indicator of the extraction
motor is (Fig. 8). Accompany the panel with
your hands during the opening.
Following the panel opening, you can access
the grease filter and after its removal, acting
on the appropriate handle, you can reach the
seat of the charcoal filter (fig. 9).
To close the panel, simply bring it in hori-
zontal position until it the automatic closing
coupling occurs.
It is possible to install a main cooker hood with a
further one or two MODULES SLT955 - SLT956
in a single extraction system and then connect it
to a single, internal or external, remote extraction
motor of the home.
An extraction system, formed of more than one
element, is controlled by a single remote con-
trol because only a main cooker hood SLT955 or
SLT956 has all the electronic components nec-
essary for the functioning, whilst the remaining
MODULES SLT955 or SLT956 are dependent on
the main cooker hood SLT955 or SLT956.
Other combinations can also be realised between
products SLT955 and SLT956 because only one
main cooker hood (SLT955 or SLT956) is present
and two modules at the maximum.
A minimum distance of at least 110 mm is recom-
mended between the openings of the plasterboard
(Fig. 15) and a maximum distance of 1,000 mm.
A B C
7
13
EXTRACTION VERSIONS:
A: SLT955/SLT956 ............................................................................... remote motor SEM1-8*
B: SLT955/SLT956 + 1 x SLT955/SLT956 module......................................remote motor SEM8
C: SLT955/SLT956 + 2 x SLT955/SLT956 module......................................remote motor SEM8
D: SLT955/SLT956............................................................................... remote motor SEM2-7*
E: SLT955/SLT956 + 1 x SLT955/SLT956 module ..................................... remote motor SEM7
F: SLT955/SLT956 + 2 x SLT955/SLT956 module ..................................... remote motor SEM7
FILTER VERSIONS:
G: SLT955/SLT956............................................... remote motor SEM1-8* + air deviator S-DF2
H: SLT955/SLT956 + 1 or 2 x SLT955/SLT956 modules . remote motor SEM8 + air deviator S-DF2
*High performance
D E F
G H
8
°~°
13
WORKING
OPERATION
M
O
D
E
Standard con
fii
gu
r
a
tii
on:
Standard configuration requires all “cooker hoods
–
radio control
-
system”
to
be provided with the same
transmission code.
In
the event two cooker hoods
–
radio control system are installed
in
the same
room
or
nearby, each system may affect the operation
of
the another. Therefore, the code
of
one radio
control
system must be
changed.
Generatiing a new transmiissiion
cod
e
:
The
radio control
system
is
provided
with
preset
codes. Should new codes
be
required, proceed
as
follows: Press simultaneously
buttons:
for
two seconds. When Leds light on, press buttons:
(within 5
seconds). Leds flashing
3
times indicate
the procedure
is
completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
RC001
GB
R
ADIO
C
O
N
T
R
O
L
Radio control used
for
the remote operation
of duct-
ed cooker
hoods.
T
ECH NIICAL
DA
T
A
-
Alkaline battery
powered :
12 V mod. 23 A
-
Operating
frequency :
433.92
Mhz
- Combinations : 32.768
-
Max.
consumption :
25
mA
-
Operating
temperature :
-20
÷ +
55
°C
- Dimensions :
120
x
45
x
15
mm.
O
PE RATIING
D
E
S
C
R
II
P
T
II
O
N
The transmitter
is
equipped with
5
buttons
for cook-
er hood management, as specified
below:
:
Light ON/OFF
command.
:
Motor ON (speed level
1) /
OFF
command.
:
Reduce
speed.
:
Increase
speed.
:
10-minute
timer.
I
NIITIIAL
O
PERATIING
CO
ND
II
T
II
O
N
The manufacturer supplies
the radio control unit
ready
to
be used with codes preset
in
the
Factory.
Learniing the new transmiissiion cod
e
:
Once the transmission code
is
changed
in
the
radio
control unit, the electronic central unit
of
the cooker
hood must be made
to
set the new code
in
the
fol-
lowing
way:
Press
the main
power-off button
of the hood and
then
restore
power to the
electronic
control unit.
Within the next
15
seconds, press the Liight
Button
to
synchronise the central unit with the
code.
Reset
of
the Factory
con
fii
gu
r
a
tii
on:
To restore the Factory configuration, follow the
pro-
cedure described below: press simultaneously
but-
tons
for 2
seconds. When Leds light on, press buttons
(within 5
seconds). Leds flashing
6
times indicate
the procedure
is completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
Emergency
bu
tt
on:
In the event that the radio control does not work,
use
the
emergency button
to
switch
the
appliance
off.
After any
necessary repairs have been performed,
reset the emergency
button.
W
ARN
II
N
G
The battery should be replaced every year
to guar-
antee the optimal range
of
the
transmitter.
To
replace
the
exhausted battery, take
the
plastic
lid
off, remove the battery and replace
it
with a
new
one, observing the correct battery
polarities.
Used batteries should be discarded
in
special
col-
lection
bins.
The
below product:
RC001 R adiio
C
on
tr
o
ll
complies
with the
specifications
set out in the
R&TTE Directive 99/5/EC.
W
ARN
I
N
G
Any adjustments
or
modifications which have
not
been expressly approved by the holder
of
the
legal
conformity
certificate
may
invalidate
the
user’s
rights relating
to
the operation
of
the
device.
Rev. 0 2 6 /08/14
OPERATION
M
O
D
E
Standard con
fii
gu
r
a
tii
on:
Standard configuration requires all “cooker hoods
–
radio control
-
system”
to
be provided with the same
transmission code.
In
the event two cooker hoods
–
radio control system are installed
in
the same
room
or
nearby, each system may affect the operation
of
the another. Therefore, the code
of
one radio
control
system must be
changed.
Generatiing a new transmiissiion
cod
e
:
The
radio control
system
is
provided
with
preset
codes. Should new codes
be
required, proceed
as
follows: Press simultaneously
buttons:
for
two seconds. When Leds light on, press buttons:
(within 5
seconds). Leds flashing
3
times indicate
the procedure
is
completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
14
WORKING
Radio remote control or the remote control
of cooker hoods (Fig. 13).
Technical data:
- Alkaline battery powered: 12V mod 23A
- Operating frequency: 433.92 MHz
- Max. consumption: 25 mA
- Operating temperature: - 20 + 55°C
Working description:
- To light the cooker hood on or to light it off
press the button:
- To increase the speed up to the fourth one
press the button:
- To reduce the speed up to the second one
press the button:
The set suction speed is shown by the LED
in the perimeter extraction channel (fig. 8).
Each LED colour corresponds to a different
speed, as shown below:
First speed WHITE
Second speed LIGHT BLUE
Third speed BLUE
Fourth speed RED
- To go from a high speed back to the first
one press twice the button:
- To give power to the lights or to shut them
down press the button:
- To set the timer up press the button:
The LED on the right side will start to flash
(every 5 seconds), the hood will work for 10
minutes at the selected speed and then it
lights automatically off.
If the client increases or reduces the speed
while the timer is on, this is automatically
stopped.
Working mode:
The first time the system is switched on,
hold down the light key to set the hood
with the remote control.
If two cookerhoods-radiocontrol system are
installed in the same room or in the imme-
diate vicinity, each system may affect the
operation of the other, due to the fact that
they have the same code. Therefore it will be
necessary to change the code of one of the
radio controls.
Warning: The battery should be replaced
every year to guarantee the optimal range of
the transmitter.
To replace the exhausted battery, take the
plastic lid off, remove the battery and replace
it with a new one, observing the correct bat-
tery polarities. Used batteries should be dis-
carded in special collection bins.
The appliance has an electronic device to
switch it off automatically four hours after the
last operation carried out.
Generating a new transmission code. The
radio control is supplied with preset factory
codes.
If you want to create a new set of codes,
proceed as follows: press and hold the UP,
STOP and DOWN buttons simultaneously for
2 seconds. After the LEDS light up, press the
UP and DOWN buttons within 5 seconds. The
LEDS will flash 3 times to indicate that the
process is completed.
Warning: This procedure deletes all previ-
ously stored codes.
Learning the new transmission code:
After changing the transmission code on the
radio control, the cooker hood electronic
control unit must be made to set the new
code as follows: Press the emergency but-
ton twice consecutively to cut off power to
the appliance and reset it; from this moment,
there are 15 seconds to press the light key
so that the hood synchronises itself with
the new code.
OPERATION
M
O
D
E
Standard con
fii
gu
r
a
tii
on:
Standard configuration requires all “cooker hoods
–
radio control
-
system”
to
be provided with the same
transmission code.
In
the event two cooker hoods
–
radio control system are installed
in
the same
room
or
nearby, each system may affect the operation
of
the another. Therefore, the code
of
one radio
control
system must be
changed.
Generatiing a new transmiissiion
cod
e
:
The
radio control
system
is
provided
with
preset
codes. Should new codes
be
required, proceed
as
follows: Press simultaneously
buttons:
for
two seconds. When Leds light on, press buttons:
(within 5
seconds). Leds flashing
3
times indicate
the procedure
is
completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
RC001
GB
R
ADIO
C
O
N
T
R
O
L
Radio control used
for
the remote operation
of duct-
ed cooker
hoods.
T
ECH NIICAL
DA
T
A
-
Alkaline battery
powered :
12 V mod. 23 A
-
Operating
frequency :
433.92
Mhz
- Combinations : 32.768
-
Max.
consumption :
25
mA
-
Operating
temperature :
-20
÷ +
55
°C
- Dimensions :
120
x
45
x
15
mm.
O
PE RATIING
D
E
S
C
R
II
P
T
II
O
N
The transmitter
is
equipped with
5
buttons
for cook-
er hood management, as specified
below:
Light ON/OFF
command.
:
Motor ON (speed level
1) /
OFF
command.
:
Reduce
speed.
:
Increase
speed.
:
10-minute
timer.
NIITIIAL
I
O
PERATIING
CO
ND
II
T
II
O
N
The manufacturer supplies
the radio control unit
ready
to
be used with codes preset
in
the
Factory.
Learniing the new transmiissiion cod
e
:
Once the transmission code
is
changed
in
the
radio
control unit, the electronic central unit
of
the cooker
hood must be made
to
set the new code
in
the
fol-
lowing
way:
Press
the main
power-off button
of the hood and
then
restore
power to the
electronic
control unit.
Within the next
15
seconds, press the Liight
Button
to
synchronise the central unit with the
code.
Reset
of
the Factory
con
fii
gu
r
a
tii
on:
To restore the Factory configuration, follow the
pro-
cedure described below: press simultaneously
but-
tons
for 2
seconds. When Leds light on, press buttons
(within 5
seconds). Leds flashing
6
times indicate
the procedure
is completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
Emergency
bu
tt
on:
In the event that the radio control does not work,
use
the
emergency button
to
switch
the
appliance
off.
After any
necessary repairs have been performed,
reset the emergency
button.
W
ARN
II
N
G
The battery should be replaced every year
to guar-
antee the optimal range
of
the
transmitter.
To
replace
the
exhausted battery, take
the
plastic
lid
off, remove the battery and replace
it
with a
new
one, observing the correct battery
polarities.
Used batteries should be discarded
in
special
col-
lection
bins.
The
below product:
RC001 R adiio
C
on
tr
o
ll
complies
with the
specifications
set out in the
R&TTE Directive 99/5/EC.
W
ARN
I
N
G
Any adjustments
or
modifications which have
not
been expressly approved by the holder
of
the
legal
conformity
certificate
may
invalidate
the
user’s
rights relating
to
the operation
of
the
device.
Rev. 0 2 6 /08/14
14
WORKING
Radio remote control or the remote control
of cooker hoods (Fig. 13).
Technical data:
- Alkaline battery powered: 12V mod 23A
- Operating frequency: 433.92 MHz
- Max. consumption: 25 mA
- Operating temperature: - 20 + 55°C
Working description:
- To light the cooker hood on or to light it off
press the button:
- To increase the speed up to the fourth one
press the button:
- To reduce the speed up to the second one
press the button:
The set suction speed is shown by the LED
in the perimeter extraction channel (fig. 8).
Each LED colour corresponds to a different
speed, as shown below:
First speed WHITE
Second speed LIGHT BLUE
Third speed BLUE
Fourth speed RED
- To go from a high speed back to the first
one press twice the button:
- To give power to the lights or to shut them
down press the button:
- To set the timer up press the button:
The LED on the right side will start to flash
(every 5 seconds), the hood will work for 10
minutes at the selected speed and then it
lights automatically off.
If the client increases or reduces the speed
while the timer is on, this is automatically
stopped.
Working mode:
The first time the system is switched on,
hold down the light key to set the hood
with the remote control.
If two cookerhoods-radiocontrol system are
installed in the same room or in the imme-
diate vicinity, each system may affect the
operation of the other, due to the fact that
they have the same code. Therefore it will be
necessary to change the code of one of the
radio controls.
Warning: The battery should be replaced
every year to guarantee the optimal range of
the transmitter.
To replace the exhausted battery, take the
plastic lid off, remove the battery and replace
it with a new one, observing the correct bat-
tery polarities. Used batteries should be dis-
carded in special collection bins.
The appliance has an electronic device to
switch it off automatically four hours after the
last operation carried out.
Generating a new transmission code. The
radio control is supplied with preset factory
codes.
If you want to create a new set of codes,
proceed as follows: press and hold the UP,
STOP and DOWN buttons simultaneously for
2 seconds. After the LEDS light up, press the
UP and DOWN buttons within 5 seconds. The
LEDS will flash 3 times to indicate that the
process is completed.
Warning: This procedure deletes all previ-
ously stored codes.
Learning the new transmission code:
After changing the transmission code on the
radio control, the cooker hood electronic
control unit must be made to set the new
code as follows: Press the emergency but-
ton twice consecutively to cut off power to
the appliance and reset it; from this moment,
there are 15 seconds to press the light key
so that the hood synchronises itself with
the new code.
OPERATION
M
O
D
E
Standard con
fii
gu
r
a
tii
on:
Standard configuration requires all “cooker hoods
–
radio control
-
system”
to
be provided with the same
transmission code.
In
the event two cooker hoods
–
radio control system are installed
in
the same
room
or
nearby, each system may affect the operation
of
the another. Therefore, the code
of
one radio
control
system must be
changed.
Generatiing a new transmiissiion
cod
e
:
The
radio control
system
is
provided
with
preset
codes. Should new codes
be
required, proceed
as
follows: Press simultaneously
buttons:
for
two seconds. When Leds light on, press buttons:
(within 5
seconds). Leds flashing
3
times indicate
the procedure
is
completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
RC001
GB
R
ADIO
C
O
N
T
R
O
L
Radio control used
for
the remote operation
of duct-
ed cooker
hoods.
T
ECH NIICAL
DA
T
A
-
Alkaline battery
powered :
12 V mod. 23 A
-
Operating
frequency :
433.92
Mhz
- Combinations : 32.768
-
Max.
consumption :
25
mA
-
Operating
temperature :
-20
÷ +
55
°C
- Dimensions :
120
x
45
x
15
mm.
O
PE RATIING
D
E
S
C
R
II
P
T
II
O
N
The transmitter
is
equipped with
5
buttons
for cook-
er hood management, as specified
below:
:
Light ON/OFF
command.
:
Motor ON (speed level
1) /
OFF
command.
:
Reduce
speed.
:
Increase
speed.
:
10-minute
timer.
I
NIITIIAL
O
PERATIING
CO
ND
II
T
II
O
N
The manufacturer supplies
the radio control unit
ready
to
be used with codes preset
in
the
Factory.
Learniing the new transmiissiion cod
e
:
Once the transmission code
is
changed
in
the
radio
control unit, the electronic central unit
of
the cooker
hood must be made
to
set the new code
in
the
fol-
lowing
way:
Press
the main
power-off button
of the hood and
then
restore
power to the
electronic
control unit.
Within the next
15
seconds, press the Liight
Button
to
synchronise the central unit with the
code.
Reset
of
the Factory
con
fii
gu
r
a
tii
on:
To restore the Factory configuration, follow the
pro-
cedure described below: press simultaneously
but-
tons
for 2
seconds. When Leds light on, press buttons
(within 5
seconds). Leds flashing
6
times indicate
the procedure
is completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
Emergency
bu
tt
on:
In the event that the radio control does not work,
use
the
emergency button
to
switch
the
appliance
off.
After any
necessary repairs have been performed,
reset the emergency
button.
W
ARN
II
N
G
The battery should be replaced every year
to guar-
antee the optimal range
of
the
transmitter.
To
replace
the
exhausted battery, take
the
plastic
lid
off, remove the battery and replace
it
with a
new
one, observing the correct battery
polarities.
Used batteries should be discarded
in
special
col-
lection
bins.
The
below product:
RC001 R adiio
C
on
tr
o
ll
complies
with the
specifications
set out in the
R&TTE Directive 99/5/EC.
W
ARN
I
N
G
Any adjustments
or
modifications which have
not
been expressly approved by the holder
of
the
legal
conformity
certificate
may
invalidate
the
user’s
rights relating
to
the operation
of
the
device.
Rev. 0 2 6 /08/14
14
WORKING
Radio remote control or the remote control
of cooker hoods (Fig. 13).
Technical data:
- Alkaline battery powered: 12V mod 23A
- Operating frequency: 433.92 MHz
- Max. consumption: 25 mA
- Operating temperature: - 20 + 55°C
Working description:
- To light the cooker hood on or to light it off
press the button:
- To increase the speed up to the fourth one
press the button:
- To reduce the speed up to the second one
press the button:
The set suction speed is shown by the LED
in the perimeter extraction channel (fig. 8).
Each LED colour corresponds to a different
speed, as shown below:
First speed WHITE
Second speed LIGHT BLUE
Third speed BLUE
Fourth speed RED
- To go from a high speed back to the first
one press twice the button:
- To give power to the lights or to shut them
down press the button:
- To set the timer up press the button:
The LED on the right side will start to flash
(every 5 seconds), the hood will work for 10
minutes at the selected speed and then it
lights automatically off.
If the client increases or reduces the speed
while the timer is on, this is automatically
stopped.
Working mode:
The first time the system is switched on,
hold down the light key to set the hood
with the remote control.
If two cookerhoods-radiocontrol system are
installed in the same room or in the imme-
diate vicinity, each system may affect the
operation of the other, due to the fact that
they have the same code. Therefore it will be
necessary to change the code of one of the
radio controls.
Warning: The battery should be replaced
every year to guarantee the optimal range of
the transmitter.
To replace the exhausted battery, take the
plastic lid off, remove the battery and replace
it with a new one, observing the correct bat-
tery polarities. Used batteries should be dis-
carded in special collection bins.
The appliance has an electronic device to
switch it off automatically four hours after the
last operation carried out.
Generating a new transmission code. The
radio control is supplied with preset factory
codes.
If you want to create a new set of codes,
proceed as follows: press and hold the UP,
STOP and DOWN buttons simultaneously for
2 seconds. After the LEDS light up, press the
UP and DOWN buttons within 5 seconds. The
LEDS will flash 3 times to indicate that the
process is completed.
Warning: This procedure deletes all previ-
ously stored codes.
Learning the new transmission code:
After changing the transmission code on the
radio control, the cooker hood electronic
control unit must be made to set the new
code as follows: Press the emergency but-
ton twice consecutively to cut off power to
the appliance and reset it; from this moment,
there are 15 seconds to press the light key
so that the hood synchronises itself with
the new code.
OPERATION
M
O
D
E
Standard con
fii
gu
r
a
tii
on:
Standard configuration requires all “cooker hoods
–
radio control
-
system”
to
be provided with the same
transmission code.
In
the event two cooker hoods
–
radio control system are installed
in
the same
room
or
nearby, each system may affect the operation
of
the another. Therefore, the code
of
one radio
control
system must be
changed.
Generatiing a new transmiissiion
cod
e
:
The
radio control
system
is
provided
with
preset
codes. Should new codes
be
required, proceed
as
follows: Press simultaneously
buttons:
for
two seconds. When Leds light on, press buttons:
(within 5
seconds). Leds flashing
3
times indicate
the procedure
is
completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
RC001
GB
R
ADIO
C
O
N
T
R
O
L
Radio control used
for
the remote operation
of duct-
ed cooker
hoods.
T
ECH NIICAL
DA
T
A
-
Alkaline battery
powered :
12 V mod. 23 A
-
Operating
frequency :
433.92
Mhz
- Combinations : 32.768
-
Max.
consumption :
25
mA
-
Operating
temperature :
-20
÷ +
55
°C
- Dimensions :
120
x
45
x
15
mm.
O
PE RATIING
D
E
S
C
R
II
P
T
II
O
N
The transmitter
is
equipped with
5
buttons
for cook-
er hood management, as specified
below:
:
Light ON/OFF
command.
:
Motor ON (speed level
1) /
OFF
command.
:
Reduce
speed.
:
Increase
speed.
:
10-minute
timer.
I
NIITIIAL
O
PERATIING
CO
ND
II
T
II
O
N
The manufacturer supplies
the radio control unit
ready
to
be used with codes preset
in
the
Factory.
Learniing the new transmiissiion cod
e
:
Once the transmission code
is
changed
in
the
radio
control unit, the electronic central unit
of
the cooker
hood must be made
to
set the new code
in
the
fol-
lowing
way:
Press
the main
power-off button
of the hood and
then
restore
power to the
electronic
control unit.
Within the next
15
seconds, press the Liight
Button
to
synchronise the central unit with the
code.
Reset
of
the Factory
con
fii
gu
r
a
tii
on:
To restore the Factory configuration, follow the
pro-
cedure described below: press simultaneously
but-
tons
for 2
seconds. When Leds light on, press buttons
(within 5
seconds). Leds flashing
6
times indicate
the procedure
is completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
Emergency
bu
tt
on:
In the event that the radio control does not work,
use
the
emergency button
to
switch
the
appliance
off.
After any
necessary repairs have been performed,
reset the emergency
button.
W
ARN
II
N
G
The battery should be replaced every year
to guar-
antee the optimal range
of
the
transmitter.
To
replace
the
exhausted battery, take
the
plastic
lid
off, remove the battery and replace
it
with a
new
one, observing the correct battery
polarities.
Used batteries should be discarded
in
special
col-
lection
bins.
The
below product:
RC001 R adiio
C
on
tr
o
ll
complies
with the
specifications
set out in the
R&TTE Directive 99/5/EC.
W
ARN
I
N
G
Any adjustments
or
modifications which have
not
been expressly approved by the holder
of
the
legal
conformity
certificate
may
invalidate
the
user’s
rights relating
to
the operation
of
the
device.
Rev. 0 2 6 /08/14
14
WORKING
Radio remote control or the remote control
of cooker hoods (Fig. 13).
Technical data:
- Alkaline battery powered: 12V mod 23A
- Operating frequency: 433.92 MHz
- Max. consumption: 25 mA
- Operating temperature: - 20 + 55°C
Working description:
- To light the cooker hood on or to light it off
press the button:
- To increase the speed up to the fourth one
press the button:
- To reduce the speed up to the second one
press the button:
The set suction speed is shown by the LED
in the perimeter extraction channel (fig. 8).
Each LED colour corresponds to a different
speed, as shown below:
First speed WHITE
Second speed LIGHT BLUE
Third speed BLUE
Fourth speed RED
- To go from a high speed back to the first
one press twice the button:
- To give power to the lights or to shut them
down press the button:
- To set the timer up press the button:
The LED on the right side will start to flash
(every 5 seconds), the hood will work for 10
minutes at the selected speed and then it
lights automatically off.
If the client increases or reduces the speed
while the timer is on, this is automatically
stopped.
Working mode:
The first time the system is switched on,
hold down the light key to set the hood
with the remote control.
If two cookerhoods-radiocontrol system are
installed in the same room or in the imme-
diate vicinity, each system may affect the
operation of the other, due to the fact that
they have the same code. Therefore it will be
necessary to change the code of one of the
radio controls.
Warning: The battery should be replaced
every year to guarantee the optimal range of
the transmitter.
To replace the exhausted battery, take the
plastic lid off, remove the battery and replace
it with a new one, observing the correct bat-
tery polarities. Used batteries should be dis-
carded in special collection bins.
The appliance has an electronic device to
switch it off automatically four hours after the
last operation carried out.
Generating a new transmission code. The
radio control is supplied with preset factory
codes.
If you want to create a new set of codes,
proceed as follows: press and hold the UP,
STOP and DOWN buttons simultaneously for
2 seconds. After the LEDS light up, press the
UP and DOWN buttons within 5 seconds. The
LEDS will flash 3 times to indicate that the
process is completed.
Warning: This procedure deletes all previ-
ously stored codes.
Learning the new transmission code:
After changing the transmission code on the
radio control, the cooker hood electronic
control unit must be made to set the new
code as follows: Press the emergency but-
ton twice consecutively to cut off power to
the appliance and reset it; from this moment,
there are 15 seconds to press the light key
so that the hood synchronises itself with
the new code.
OPERATION
M
O
D
E
Standard con
fii
gu
r
a
tii
on:
Standard configuration requires all “cooker hoods
–
radio control
-
system”
to
be provided with the same
transmission code.
In
the event two cooker hoods
–
radio control system are installed
in
the same
room
or
nearby, each system may affect the operation
of
the another. Therefore, the code
of
one radio
control
system must be
changed.
Generatiing a new transmiissiion
cod
e
:
The
radio control
system
is
provided
with
preset
codes. Should new codes
be
required, proceed
as
follows: Press simultaneously
buttons:
for
two seconds. When Leds light on, press buttons:
(within 5
seconds). Leds flashing
3
times indicate
the procedure
is
completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
RC001
GB
R
ADIO
C
O
N
T
R
O
L
Radio control used
for
the remote operation
of duct-
ed cooker
hoods.
T
ECH NIICAL
DA
T
A
-
Alkaline battery
powered :
12 V mod. 23 A
-
Operating
frequency :
433.92
Mhz
- Combinations : 32.768
-
Max.
consumption :
25
mA
-
Operating
temperature :
-20
÷ +
55
°C
- Dimensions :
120
x
45
x
15
mm.
O
PE RATIING
D
E
S
C
R
II
P
T
II
O
N
The transmitter
is
equipped with
5
buttons
for cook-
er hood management, as specified
below:
:
Light ON/OFF
command.
:
Motor ON (speed level
1) /
OFF
command.
:
Reduce
speed.
:
Increase
speed.
:
10-minute
timer.
I
NIITIIAL
O
PERATIING
CO
ND
II
T
II
O
N
The manufacturer supplies
the radio control unit
ready
to
be used with codes preset
in
the
Factory.
Learniing the new transmiissiion cod
e
:
Once the transmission code
is
changed
in
the
radio
control unit, the electronic central unit
of
the cooker
hood must be made
to
set the new code
in
the
fol-
lowing
way:
Press
the main
power-off button
of the hood and
then
restore
power to the
electronic
control unit.
Within the next
15
seconds, press the Liight
Button
to
synchronise the central unit with the
code.
Reset
of
the Factory
con
fii
gu
r
a
tii
on:
To restore the Factory configuration, follow the
pro-
cedure described below: press simultaneously
but-
tons
for 2
seconds. When Leds light on, press buttons
(within 5
seconds). Leds flashing
6
times indicate
the procedure
is completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
Emergency
bu
tt
on:
In the event that the radio control does not work,
use
the
emergency button
to
switch
the
appliance
off.
After any
necessary repairs have been performed,
reset the emergency
button.
W
ARN
II
N
G
The battery should be replaced every year
to guar-
antee the optimal range
of
the
transmitter.
To
replace
the
exhausted battery, take
the
plastic
lid
off, remove the battery and replace
it
with a
new
one, observing the correct battery
polarities.
Used batteries should be discarded
in
special
col-
lection
bins.
The
below product:
RC001 R adiio
C
on
tr
o
ll
complies
with the
specifications
set out in the
R&TTE Directive 99/5/EC.
W
ARN
I
N
G
Any adjustments
or
modifications which have
not
been expressly approved by the holder
of
the
legal
conformity
certificate
may
invalidate
the
user’s
rights relating
to
the operation
of
the
device.
Rev. 0 2 6 /08/14
14
WORKING
Radio remote control or the remote control
of cooker hoods (Fig. 13).
Technical data:
- Alkaline battery powered: 12V mod 23A
- Operating frequency: 433.92 MHz
- Max. consumption: 25 mA
- Operating temperature: - 20 + 55°C
Working description:
- To light the cooker hood on or to light it off
press the button:
- To increase the speed up to the fourth one
press the button:
- To reduce the speed up to the second one
press the button:
The set suction speed is shown by the LED
in the perimeter extraction channel (fig. 8).
Each LED colour corresponds to a different
speed, as shown below:
First speed WHITE
Second speed LIGHT BLUE
Third speed BLUE
Fourth speed RED
- To go from a high speed back to the first
one press twice the button:
- To give power to the lights or to shut them
down press the button:
- To set the timer up press the button:
The LED on the right side will start to flash
(every 5 seconds), the hood will work for 10
minutes at the selected speed and then it
lights automatically off.
If the client increases or reduces the speed
while the timer is on, this is automatically
stopped.
Working mode:
The first time the system is switched on,
hold down the light key to set the hood
with the remote control.
If two cookerhoods-radiocontrol system are
installed in the same room or in the imme-
diate vicinity, each system may affect the
operation of the other, due to the fact that
they have the same code. Therefore it will be
necessary to change the code of one of the
radio controls.
Warning: The battery should be replaced
every year to guarantee the optimal range of
the transmitter.
To replace the exhausted battery, take the
plastic lid off, remove the battery and replace
it with a new one, observing the correct bat-
tery polarities. Used batteries should be dis-
carded in special collection bins.
The appliance has an electronic device to
switch it off automatically four hours after the
last operation carried out.
Generating a new transmission code. The
radio control is supplied with preset factory
codes.
If you want to create a new set of codes,
proceed as follows: press and hold the UP,
STOP and DOWN buttons simultaneously for
2 seconds. After the LEDS light up, press the
UP and DOWN buttons within 5 seconds. The
LEDS will flash 3 times to indicate that the
process is completed.
Warning: This procedure deletes all previ-
ously stored codes.
Learning the new transmission code:
After changing the transmission code on the
radio control, the cooker hood electronic
control unit must be made to set the new
code as follows: Press the emergency but-
ton twice consecutively to cut off power to
the appliance and reset it; from this moment,
there are 15 seconds to press the light key
so that the hood synchronises itself with
the new code.
OPERATION
M
O
D
E
Standard con
fii
gu
r
a
tii
on:
Standard configuration requires all “cooker hoods
–
radio control
-
system”
to
be provided with the same
transmission code.
In
the event two cooker hoods
–
radio control system are installed
in
the same
room
or
nearby, each system may affect the operation
of
the another. Therefore, the code
of
one radio
control
system must be
changed.
Generatiing a new transmiissiion
cod
e
:
The
radio control
system
is
provided
with
preset
codes. Should new codes
be
required, proceed
as
follows: Press simultaneously
buttons:
for
two seconds. When Leds light on, press buttons:
(within 5
seconds). Leds flashing
3
times indicate
the procedure
is
completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
RC001
GB
R
ADIO
C
O
N
T
R
O
L
Radio control used
for
the remote operation
of duct-
ed cooker
hoods.
T
ECH NIICAL
DA
T
A
-
Alkaline battery
powered :
12 V mod. 23 A
-
Operating
frequency :
433.92
Mhz
- Combinations : 32.768
-
Max.
consumption :
25
mA
-
Operating
temperature :
-20
÷ +
55
°C
- Dimensions :
120
x
45
x
15
mm.
O
PE RATIING
D
E
S
C
R
II
P
T
II
O
N
The transmitter
is
equipped with
5
buttons
for cook-
er hood management, as specified
below:
:
Light ON/OFF
command.
:
Motor ON (speed level
1) /
OFF
command.
:
Reduce
speed.
:
Increase
speed.
:
10-minute
timer.
I
NIITIIAL
O
PERATIING
CO
ND
II
T
II
O
N
The manufacturer supplies
the radio control unit
ready
to
be used with codes preset
in
the
Factory.
Learniing the new transmiissiion cod
e
:
Once the transmission code
is
changed
in
the
radio
control unit, the electronic central unit
of
the cooker
hood must be made
to
set the new code
in
the
fol-
lowing
way:
Press
the main
power-off button
of the hood and
then
restore
power to the
electronic
control unit.
Within the next
15
seconds, press the Liight
Button
to
synchronise the central unit with the
code.
Reset
of
the Factory
con
fii
gu
r
a
tii
on:
To restore the Factory configuration, follow the
pro-
cedure described below: press simultaneously
but-
tons
for 2
seconds. When Leds light on, press buttons
(within 5
seconds). Leds flashing
6
times indicate
the procedure
is completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
Emergency
bu
tt
on:
In the event that the radio control does not work,
use
the
emergency button
to
switch
the
appliance
off.
After any
necessary repairs have been performed,
reset the emergency
button.
W
ARN
II
N
G
The battery should be replaced every year
to guar-
antee the optimal range
of
the
transmitter.
To
replace
the
exhausted battery, take
the
plastic
lid
off, remove the battery and replace
it
with a
new
one, observing the correct battery
polarities.
Used batteries should be discarded
in
special
col-
lection
bins.
The
below product:
RC001 R adiio
C
on
tr
o
ll
complies
with the
specifications
set out in the
R&TTE Directive 99/5/EC.
W
ARN
I
N
G
Any adjustments
or
modifications which have
not
been expressly approved by the holder
of
the
legal
conformity
certificate
may
invalidate
the
user’s
rights relating
to
the operation
of
the
device.
Rev. 0 2 6 /08/14
14
WORKING
Radio remote control or the remote control
of cooker hoods (Fig. 13).
Technical data:
- Alkaline battery powered: 12V mod 23A
- Operating frequency: 433.92 MHz
- Max. consumption: 25 mA
- Operating temperature: - 20 + 55°C
Working description:
- To light the cooker hood on or to light it off
press the button:
- To increase the speed up to the fourth one
press the button:
- To reduce the speed up to the second one
press the button:
The set suction speed is shown by the LED
in the perimeter extraction channel (fig. 8).
Each LED colour corresponds to a different
speed, as shown below:
First speed WHITE
Second speed LIGHT BLUE
Third speed BLUE
Fourth speed RED
- To go from a high speed back to the first
one press twice the button:
- To give power to the lights or to shut them
down press the button:
- To set the timer up press the button:
The LED on the right side will start to flash
(every 5 seconds), the hood will work for 10
minutes at the selected speed and then it
lights automatically off.
If the client increases or reduces the speed
while the timer is on, this is automatically
stopped.
Working mode:
The first time the system is switched on,
hold down the light key to set the hood
with the remote control.
If two cookerhoods-radiocontrol system are
installed in the same room or in the imme-
diate vicinity, each system may affect the
operation of the other, due to the fact that
they have the same code. Therefore it will be
necessary to change the code of one of the
radio controls.
Warning: The battery should be replaced
every year to guarantee the optimal range of
the transmitter.
To replace the exhausted battery, take the
plastic lid off, remove the battery and replace
it with a new one, observing the correct bat-
tery polarities. Used batteries should be dis-
carded in special collection bins.
The appliance has an electronic device to
switch it off automatically four hours after the
last operation carried out.
Generating a new transmission code. The
radio control is supplied with preset factory
codes.
If you want to create a new set of codes,
proceed as follows: press and hold the UP,
STOP and DOWN buttons simultaneously for
2 seconds. After the LEDS light up, press the
UP and DOWN buttons within 5 seconds. The
LEDS will flash 3 times to indicate that the
process is completed.
Warning: This procedure deletes all previ-
ously stored codes.
Learning the new transmission code:
After changing the transmission code on the
radio control, the cooker hood electronic
control unit must be made to set the new
code as follows: Press the emergency but-
ton twice consecutively to cut off power to
the appliance and reset it; from this moment,
there are 15 seconds to press the light key
so that the hood synchronises itself with
the new code.
OPERATION
M
O
D
E
Standard con
fii
gu
r
a
tii
on:
Standard configuration requires all “cooker hoods
–
radio control
-
system”
to
be provided with the same
transmission code.
In
the event two cooker hoods
–
radio control system are installed
in
the same
room
or
nearby, each system may affect the operation
of
the another. Therefore, the code
of
one radio
control
system must be
changed.
Generatiing a new transmiissiion
cod
e
:
The
radio control
system
is
provided
with
preset
codes. Should new codes
be
required, proceed
as
follows: Press simultaneously
buttons:
for
two seconds. When Leds light on, press buttons:
(within 5
seconds). Leds flashing
3
times indicate
the procedure
is
completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
RC001
GB
R
ADIO
C
O
N
T
R
O
L
Radio control used
for
the remote operation
of duct-
ed cooker
hoods.
T
ECH NIICAL
DA
T
A
-
Alkaline battery
powered :
12 V mod. 23 A
-
Operating
frequency :
433.92
Mhz
- Combinations : 32.768
-
Max.
consumption :
25
mA
-
Operating
temperature :
-20
÷ +
55
°C
- Dimensions :
120
x
45
x
15
mm.
O
PE RATIING
D
E
S
C
R
II
P
T
II
O
N
The transmitter
is
equipped with
5
buttons
for cook-
er hood management, as specified
below:
:
Light ON/OFF
command.
:
Motor ON (speed level
1) /
OFF
command.
:
Reduce
speed.
:
Increase
speed.
:
10-minute
timer.
I
NIITIIAL
O
PERATIING
CO
ND
II
T
II
O
N
The manufacturer supplies
the radio control unit
ready
to
be used with codes preset
in
the
Factory.
Learniing the new transmiissiion cod
e
:
Once the transmission code
is
changed
in
the
radio
control unit, the electronic central unit
of
the cooker
hood must be made
to
set the new code
in
the
fol-
lowing
way:
Press
the main
power-off button
of the hood and
then
restore
power to the
electronic
control unit.
Within the next
15
seconds, press the Liight
Button
to
synchronise the central unit with the
code.
Reset
of
the Factory
con
fii
gu
r
a
tii
on:
To restore the Factory configuration, follow the
pro-
cedure described below: press simultaneously
but-
tons
for 2
seconds. When Leds light on, press buttons
(within 5
seconds). Leds flashing
6
times indicate
the procedure
is completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
Emergency
bu
tt
on:
In the event that the radio control does not work,
use
the
emergency button
to
switch
the
appliance
off.
After any
necessary repairs have been performed,
reset the emergency
button.
W
ARN
II
N
G
The battery should be replaced every year
to guar-
antee the optimal range
of
the
transmitter.
To
replace
the
exhausted battery, take
the
plastic
lid
off, remove the battery and replace
it
with a
new
one, observing the correct battery
polarities.
Used batteries should be discarded
in
special
col-
lection
bins.
The
below product:
RC001 R adiio
C
on
tr
o
ll
complies
with the
specifications
set out in the
R&TTE Directive 99/5/EC.
W
ARN
I
N
G
Any adjustments
or
modifications which have
not
been expressly approved by the holder
of
the
legal
conformity
certificate
may
invalidate
the
user’s
rights relating
to
the operation
of
the
device.
Rev. 0 2 6 /08/14
13
WORKING
OPERATION
M
O
D
E
Standard con
fii
gu
r
a
tii
on:
Standard configuration requires all “cooker hoods
–
radio control
-
system”
to
be provided with the same
transmission code.
In
the event two cooker hoods
–
radio control system are installed
in
the same
room
or
nearby, each system may affect the operation
of
the another. Therefore, the code
of
one radio
control
system must be
changed.
Generatiing a new transmiissiion
cod
e
:
The
radio control
system
is
provided
with
preset
codes. Should new codes
be
required, proceed
as
follows: Press simultaneously
buttons:
for
two seconds. When Leds light on, press buttons:
(within 5
seconds). Leds flashing
3
times indicate
the procedure
is
completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
RC001
GB
R
ADIO
C
O
N
T
R
O
L
Radio control used
for
the remote operation
of duct-
ed cooker
hoods.
T
ECH NIICAL
DA
T
A
-
Alkaline battery
powered :
12 V mod. 23 A
-
Operating
frequency :
433.92
Mhz
- Combinations : 32.768
-
Max.
consumption :
25
mA
-
Operating
temperature :
-20
÷ +
55
°C
- Dimensions :
120
x
45
x
15
mm.
O
PE RATIING
D
E
S
C
R
II
P
T
II
O
N
The transmitter
is
equipped with
5
buttons
for cook-
er hood management, as specified
below:
:
Light ON/OFF
command.
:
Motor ON (speed level
1) /
OFF
command.
:
Reduce
speed.
:
Increase
speed.
:
10-minute
timer.
I
NIITIIAL
O
PERATIING
CO
ND
II
T
II
O
N
The manufacturer supplies
the radio control unit
ready
to
be used with codes preset
in
the
Factory.
Learniing the new transmiissiion cod
e
:
Once the transmission code
is
changed
in
the
radio
control unit, the electronic central unit
of
the cooker
hood must be made
to
set the new code
in
the
fol-
lowing
way:
Press
the main
power-off button
of the hood and
then
restore
power to the
electronic
control unit.
Within the next
15
seconds, press the Liight
Button
to
synchronise the central unit with the
code.
Reset
of
the Factory
con
fii
gu
r
a
tii
on:
To restore the Factory configuration, follow the
pro-
cedure described below: press simultaneously
but-
tons
for 2
seconds. When Leds light on, press buttons
(within 5
seconds). Leds flashing
6
times indicate
the procedure
is completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
Emergency
bu
tt
on:
In the event that the radio control does not work,
use
the
emergency button
to
switch
the
appliance
off.
After any
necessary repairs have been performed,
reset the emergency
button.
W
ARN
II
N
G
The battery should be replaced every year
to guar-
antee the optimal range
of
the
transmitter.
To
replace
the
exhausted battery, take
the
plastic
lid
off, remove the battery and replace
it
with a
new
one, observing the correct battery
polarities.
Used batteries should be discarded
in
special
col-
lection
bins.
The
below product:
RC001 R adiio
C
on
tr
o
ll
complies
with the
specifications
set out in the
R&TTE Directive 99/5/EC.
W
ARN
I
N
G
Any adjustments
or
modifications which have
not
been expressly approved by the holder
of
the
legal
conformity
certificate
may
invalidate
the
user’s
rights relating
to
the operation
of
the
device.
Rev. 0 2 6 /08/14
OPERATION
M
O
D
E
Standard con
fii
gu
r
a
tii
on:
Standard configuration requires all “cooker hoods
–
radio control
-
system”
to
be provided with the same
transmission code.
In
the event two cooker hoods
–
radio control system are installed
in
the same
room
or
nearby, each system may affect the operation
of
the another. Therefore, the code
of
one radio
control
system must be
changed.
Generatiing a new transmiissiion
cod
e
:
The
radio control
system
is
provided
with
preset
codes. Should new codes
be
required, proceed
as
follows: Press simultaneously
buttons:
for
two seconds. When Leds light on, press buttons:
(within 5
seconds). Leds flashing
3
times indicate
the procedure
is
completed.
W
ARN
I
N
G
!
This operation deletes permanently
the
preset
codes.
9
10
••••
1
4
56
2
3
11
••••
7 8
9 10
1211
12
52
13 14
15
••••
13 14
15
52
13 14
15
13
90017000955 - B 04/2013
90017100955 - GM - 04/2015
Importőr:
MULTIKOMPLEX BUDAPEST KFT.
a páraelszívók szakértője... 1995 óta
H - 1211 Budapest, Mansfeld Péter u. 27
(volt Bajáki Ferenc utca)
tel.: +(36-1) 427 0325, +(36-1) 427-0326;
fax: +(36-1)427 0327
www.multikomplex.hu
SLT955 - SLT956
INFORMAZIONI COMMERCIALI PER I CONSUMATORI
COMMERCIAL INFORMATION FOR THE CONSUMER
INFORMATIONS COMMERCIALES POUR LE CLIENT
INFORMACIONES COMERCIALES PARA EL CLIENTE
HANDELSINFORMATIONEN FÜR DEN KUNDEN
COMMERCIËLE INFORMATIES VOOR DE KLANT
INFORMAZIONI TECNICHE
TECHNICAL INFORMATION
INFORMATION TECHNIQUES
INFORMACIONES TÉCNICAS
TECHNISCHE INFORMATIONEN
TECHNISCHE INFORMATIES
ISTRUZIONI PER INSTALLAZIONE, USO E MANUTENZIONE
INSTALLATION, USE AND MAINTENANCE INSTRUCTION
INSTRUCTIONS POUR L’INSTALLATION D’EMPLOI ET D’ENTRETIEN
INSTRUCCIONES PARA LA INSTALACIÓN DE USO Y MANTENIMIENTO
INSTALLATIONSANLEITUNG FÜR DIE VERWENDUNG UND WARTUNG
INSTALLATIE INSTRUCTIES VOOR GEBRUIK EN ONDERHOUD
IT
EN
FR
ES
DE
NL
ENERGY LABEL
1
Il simbolo sul prodotto o sulla confezione indica che il prodotto non deve essere consi-
derato come un normale rifiuto domestico, ma deve essere portato nel punto di raccolta
appropriato per il riciclaggio di apparecchiature elettriche ed elettroniche. Provvedendo a
smaltire questo prodotto in modo appropriato, si contribuisce a evitare potenziali conse-
guenze negative per l’ambiente e per la salute, che potrebbero derivare da uno smaltimento
inadeguato del prodotto. Per informazioni più dettagliate sul riciclaggio di questo prodotto,
contattare l’ufficio comunale, il servizio locale di smaltimento rifiuti o il negozio in cui è
stato acquistato il prodotto. Questo elettrodomestico è marcato conformemente alla Diret-
tiva Europea 2002/96/CE sui rifiuti da apparecchiature elettriche ed elettroniche (WEEE).
IT
The symbol on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment. By ensuring this prod-
uct is disposed of correctly, you will help prevent potential negative consequences for
the environment and human health, which could otherwise be caused by inappropri-
ate waste handling of this product. For more detailed information about recycling of this
product, please contact your local city office, your household waste disposal service or
the shop where you purchased the product. This appliance is marked according to the
European directive 2002/96/EC on waste electrical and electronic equipment (WEEE).
EN
Le symbole sur le produit ou son emballage indique que ce produit ne peut être traité
comme déchet ménager. Il doit plutôt être remis au point de ramassage concerné, se
chargeant du recyclage du matériel électrique et électronique. En vous assurant que ce
produit est éliminé correctement, vous favorisez la prévention des conséquences néga-
tives pour l’environnement et la santé humaine qui, sinon, seraient le résultat d’un trai-
tement inappropriée des déchets de ce produit. Pour obtenir plus de détails sur le recy-
clage de ce produit, veuillez prendre contact avec le bureau municipal de votre région,
votre service d’élimination des déchets ménagers ou le magasin où vous avez ache-
té le produit. Cet appareil est commercialisé en accord avec la directive européenne
2002/96/CE sur les déchets del équipements électriques et électroniques (WEEE).
FR
El símbolo en el producto o en su embalaje indica que este producto no se puede tratar como
desperdicios normales del hogar. Este producto se debe entregar al punto de recolección de
equipos eléctricos y electrónicos para reciclaje. Al asegurarse de que este producto se des-
eche correctamente, usted ayudará a evitar posibles consecuencias negativas para el am-
biente y la salud pública, lo cual podría ocurrir si este producto no se manipula de forma ade-
cuada. Para obtener información más detallada sobre el reciclaje de este producto, póngase
en contacto con la administración de su ciudad, con su servicio de desechos del hogar o con
la tienda donde compró el producto. Este electrodoméstico está marcado conforme a la di-
rectiva Europea 2000/96/CE sobre los residuos de aparatos eléctricos y electrónicos (WEEE).
ES
Das Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass die-
ses Produkt nicht als normaler Haushaltsabfall zu behandeln ist, sondern an einem
Sammelpunkt für das Recycling von elektrischen und elektronischen Geräten abge-
geben werden muss. Durch Ihren Beitrag zum korrekten Entsorgen dieses Produkts
schützen Sie die Umwelt und die Gesundheit Ihrer Mitmenschen. Umwelt und Gesund-
heit werden durch falsches Entsorgen gefährdet. Weitere Informationen über das Re-
cycling dieses Produkts erhalten Sie von Ihrem Rathaus, Ihrer Müllabfuhr oder dem
Geschäft, in dem Sie das Produkt gekauft haben. Dieses Elektrohaushaltsgerät ist ent-
sprechend der EU-Richtlinie 2002/96/CE Über Elektro-und Elektronik – Altgeräte (WEEE).
DE
Het symbool op het product of op de verpakking wijst erop dat dit product niet als huis-
houdafval mag worden behandeld. Het moet echter naar een plaats worden gebracht waar
elektrische en elektronische apparatuur wordt gerecycled. Als u ervoor zorgt dat dit pro-
duct op de correcte manier wordt verwijderd, voorkomt u mogelijk voor mens en milieu
negatieve gevolgen die zich zouden kunnen voordoen in geval van verkeerde afvalbehan-
deling. Voor meer details in verband met het recyclen van dit product, neemt u het best
contact op met de gemeentelijke instanties, het bedrijf of de dienst belast met de verwij-
dering van huishoudafval of de winkel waar u het product hebt gekocht. Dit apparrat vol-
doet aan de Europese richtlijnen 2002/96/CE voor elektrische en elektronische afval (WEEE).
NL
9
CONTENTS
Warnings
Use
Installation
Panel opening
Ducting systems
Working
Maintenance
EN
10
WARNINGS
* The appliance is not intended for use by
young children or infirm persons without
supervision. Young children should be su-
pervised to ensure they do not play with the
appliance.
* The air sucked can’t be conveyed through
or into a duct used to let out fumes from
appliances fed by energy other than electric
power (eg. centralized heating, radiators,
water-heaters, etc.).
* To evacuate the air outlet, please comply
with the pertaining rules given by competent
authorities.
The cooker hood, when evacuating the sucked
air, could generate a negative pressure in the
room- which can’t exceed the limit of 0.04
mbar, in order to avoid the suck of exhausts
deriving from the heat-source.
Therefore the room should be provided with
air-intakes to allow a constant flow of fresh
air.
* When performing the electrical connections
on the appliance, please make sure that them
current-tap is provided with earth connection
and that voltage values correspond to those
indicated on the label placed inside the ap-
pliance itself.
* Please disconnect the appliance from power
mains, before carrying out any cleaning or
maintenance operation.
If the appliance is not equipped with a non-
separable flexible cable and plug, or with an-
other device ensuring omnipolar disconnec-
tion from the mains, with an opening distance
between the contacts of at least 3 mm, then
such disconnecting devices must be provided
in the fixed installation.
If the appliance is equipped with a power cord
and a plug, it shall be placed in such a way
that the plug can be reached easily.
* The use of materials which can burst into
flames (flambé) should be avoided in close
proximity of the appliance.
When frying, please pay particular attention
to fire risk due to oil and grease.
Being highly inflammable, fried oil is espe-
cially dangerous. Do not use uncovered elec-
tric grills.
In order to avoid possible fire risk, all in-
structions for grease-filter cleaning and for
removing eventual grease deposits should be
strictly followed.
* Two persons are needed for the installation
of this product.
12
USE
INSTALLATION
To install the product is necessary to make
a countertop minimum depth of at least 220
mm up to a maximum of 400 mm. For great-
er depths it is necessary to ask the special
KIT with mounting brackets for ceiling depth
from 400mm to 580mm.
Attention: If a remote motor is installed
in the same compartment as products
SLT955/SLT956, check the overall dimen-
sions of the remote motor.
You can choose the side of the hood from
which to run off the sucked air; there are air
outlets of rectangular shape on three sides
of the hood.
After choosing the best location, set up the
channel, the supply provided includes an air
outlet flange of rectangular shape 230x80mm
to be installed on the chosen outlet. Leave
closed the air exhaust holes are not used.
There is also a fitting included, that allows
the use of tubes with a diameter equal to 150
mm (see fig. 1), if you plan to create a circular
air outlet duct.
Identify a reference point compared to the
exact centre for hood installation in the solid
ceiling. Then mark out the area for the holes
to be drilled, at the points shown in figure
2 for the item SLT955 or fig. 3 for the item
SLT956.
Make the holes in the solid ceiling, using a
suitable 8 mm helical drill bit and insert the
plugs provided. It is sufficient to drill the
outer holes shown in figure 2 or figure 3; the
inner holes can be drilled after installing the
hood.
Adjust the excursion of the fixing brackets
according to the depth of the niche; min.
220mm, max. 400mm as, shown in Fig. 4.
Tighten strongly the fastening screws of the
brackets immediately after you placed them
into position.
Place the cooker hood in an established area
and fix it with the screws supplied (see fig. 5).
Perform the holes into the ceiling in corre-
spondence of the central holes of the brack-
ets and fix definitively the product by apply-
ing the remaining screws.
Make the electrical connection (see fig. 6)
and connect the air discharge pipe following
the instructions given in the related section
DUCTING SYSTEMS.
If installing an SLT 955 MODUL LIGHT or
SLT 956 MODUL LIGHT, connect the elec-
trical wire of the MODUL LIGHT hood to the
connectors shown in figure 6 on SLT955 or
SLT956.
Install the plasterboard sheet making sure
that it fits perfectly to the metal edge of the
hood (Fig 12).
The dimensions of the hole to make in the
plasterboard are:
- SLT955: 502 mm X 502 mm with two
curved sides R551,
- SLT956: 982 mm X 222 mm, use the drill-
ing template provided.
Use the 3.5 x 22 screws supplied to fix the
plasterboard to the cooker hood and insert
them using the appropriate hole template.
We recommend at least 12 screws to obtain
a good fixation.
In case the hood is provided with an internal
panel be covered in plasterboard, wood or
other material, make a sheet of the following
dimensions:
- SLT955: 448 mm X 448 mm with R524 on
the corners,
- SLT956: 928 mm X 168 mm, use the drill-
ing template supplied.
Install the sheet to the panel (fig. 7), using
the screws provided in the case of plaster-
board or using the appropriate adhesive for
the type of material to be secured.
Caution: Do not use screws longer than the
panel thickness, maximum 3.5 x 22.
The product is not equipped with the duction
motor, therefore it must be coupled to a suc-
tion unit (remote motor) of the same manu-
facturer.
12
USE
INSTALLATION
To install the product is necessary to make
a countertop minimum depth of at least 220
mm up to a maximum of 400 mm. For great-
er depths it is necessary to ask the special
KIT with mounting brackets for ceiling depth
from 400mm to 580mm.
Attention: If a remote motor is installed
in the same compartment as products
SLT955/SLT956, check the overall dimen-
sions of the remote motor.
You can choose the side of the hood from
which to run off the sucked air; there are air
outlets of rectangular shape on three sides
of the hood.
After choosing the best location, set up the
channel, the supply provided includes an air
outlet flange of rectangular shape 230x80mm
to be installed on the chosen outlet. Leave
closed the air exhaust holes are not used.
There is also a fitting included, that allows
the use of tubes with a diameter equal to 150
mm (see fig. 1), if you plan to create a circular
air outlet duct.
Identify a reference point compared to the
exact centre for hood installation in the solid
ceiling. Then mark out the area for the holes
to be drilled, at the points shown in figure
2 for the item SLT955 or fig. 3 for the item
SLT956.
Make the holes in the solid ceiling, using a
suitable 8 mm helical drill bit and insert the
plugs provided. It is sufficient to drill the
outer holes shown in figure 2 or figure 3; the
inner holes can be drilled after installing the
hood.
Adjust the excursion of the fixing brackets
according to the depth of the niche; min.
220mm, max. 400mm as, shown in Fig. 4.
Tighten strongly the fastening screws of the
brackets immediately after you placed them
into position.
Place the cooker hood in an established area
and fix it with the screws supplied (see fig. 5).
Perform the holes into the ceiling in corre-
spondence of the central holes of the brack-
ets and fix definitively the product by apply-
ing the remaining screws.
Make the electrical connection (see fig. 6)
and connect the air discharge pipe following
the instructions given in the related section
DUCTING SYSTEMS.
If installing an SLT 955 MODUL LIGHT or
SLT 956 MODUL LIGHT, connect the elec-
trical wire of the MODUL LIGHT hood to the
connectors shown in figure 6 on SLT955 or
SLT956.
Install the plasterboard sheet making sure
that it fits perfectly to the metal edge of the
hood (Fig 12).
The dimensions of the hole to make in the
plasterboard are:
- SLT955: 502 mm X 502 mm with two
curved sides R551,
- SLT956: 982 mm X 222 mm, use the drill-
ing template provided.
Use the 3.5 x 22 screws supplied to fix the
plasterboard to the cooker hood and insert
them using the appropriate hole template.
We recommend at least 12 screws to obtain
a good fixation.
In case the hood is provided with an internal
panel be covered in plasterboard, wood or
other material, make a sheet of the following
dimensions:
- SLT955: 448 mm X 448 mm with R524 on
the corners,
- SLT956: 928 mm X 168 mm, use the drill-
ing template supplied.
Install the sheet to the panel (fig. 7), using
the screws provided in the case of plaster-
board or using the appropriate adhesive for
the type of material to be secured.
Caution: Do not use screws longer than the
panel thickness, maximum 3.5 x 22.
The product is not equipped with the duction
motor, therefore it must be coupled to a suc-
tion unit (remote motor) of the same manu-
facturer.
12
USE
INSTALLATION
To install the product is necessary to make
a countertop minimum depth of at least 220
mm up to a maximum of 400 mm. For great-
er depths it is necessary to ask the special
KIT with mounting brackets for ceiling depth
from 400mm to 580mm.
Attention: If a remote motor is installed
in the same compartment as products
SLT955/SLT956, check the overall dimen-
sions of the remote motor.
You can choose the side of the hood from
which to run off the sucked air; there are air
outlets of rectangular shape on three sides
of the hood.
After choosing the best location, set up the
channel, the supply provided includes an air
outlet flange of rectangular shape 230x80mm
to be installed on the chosen outlet. Leave
closed the air exhaust holes are not used.
There is also a fitting included, that allows
the use of tubes with a diameter equal to 150
mm (see fig. 1), if you plan to create a circular
air outlet duct.
Identify a reference point compared to the
exact centre for hood installation in the solid
ceiling. Then mark out the area for the holes
to be drilled, at the points shown in figure
2 for the item SLT955 or fig. 3 for the item
SLT956.
Make the holes in the solid ceiling, using a
suitable 8 mm helical drill bit and insert the
plugs provided. It is sufficient to drill the
outer holes shown in figure 2 or figure 3; the
inner holes can be drilled after installing the
hood.
Adjust the excursion of the fixing brackets
according to the depth of the niche; min.
220mm, max. 400mm as, shown in Fig. 4.
Tighten strongly the fastening screws of the
brackets immediately after you placed them
into position.
Place the cooker hood in an established area
and fix it with the screws supplied (see fig. 5).
Perform the holes into the ceiling in corre-
spondence of the central holes of the brack-
ets and fix definitively the product by apply-
ing the remaining screws.
Make the electrical connection (see fig. 6)
and connect the air discharge pipe following
the instructions given in the related section
DUCTING SYSTEMS.
If installing an SLT 955 MODUL LIGHT or
SLT 956 MODUL LIGHT, connect the elec-
trical wire of the MODUL LIGHT hood to the
connectors shown in figure 6 on SLT955 or
SLT956.
Install the plasterboard sheet making sure
that it fits perfectly to the metal edge of the
hood (Fig 12).
The dimensions of the hole to make in the
plasterboard are:
- SLT955: 502 mm X 502 mm with two
curved sides R551,
- SLT956: 982 mm X 222 mm, use the drill-
ing template provided.
Use the 3.5 x 22 screws supplied to fix the
plasterboard to the cooker hood and insert
them using the appropriate hole template.
We recommend at least 12 screws to obtain
a good fixation.
In case the hood is provided with an internal
panel be covered in plasterboard, wood or
other material, make a sheet of the following
dimensions:
- SLT955: 448 mm X 448 mm with R524 on
the corners,
- SLT956: 928 mm X 168 mm, use the drill-
ing template supplied.
Install the sheet to the panel (fig. 7), using
the screws provided in the case of plaster-
board or using the appropriate adhesive for
the type of material to be secured.
Caution: Do not use screws longer than the
panel thickness, maximum 3.5 x 22.
The product is not equipped with the duction
motor, therefore it must be coupled to a suc-
tion unit (remote motor) of the same manu-
facturer.
11
USE
INSTALLATION
To install the product is necessary to make
a countertop minimum depth of at least 220
mm up to a maximum of 400 mm. For great-
er depths it is necessary to ask the special
KIT with mounting brackets for ceiling depth
from 400mm to 580mm.
Attention: If a remote motor is installed
in the same compartment as products
SLT955/SLT956, check the overall dimen-
sions of the remote motor.
You can choose the side of the hood from
which to run off the sucked air; there are air
outlets of rectangular shape on three sides
of the hood.
After choosing the best location, set up the
channel, the supply provided includes an air
outlet flange of rectangular shape 230x80mm
to be installed on the chosen outlet. Leave
closed the air exhaust holes are not used.
There is also a fitting included, that allows
the use of tubes with a diameter equal to 150
mm (see fig. 1), if you plan to create a circular
air outlet duct.
Identify a reference point compared to the
exact centre for hood installation in the solid
ceiling. Then mark out the area for the holes
to be drilled, at the points shown in figure
2 for the item SLT955 or fig. 3 for the item
SLT956.
Make the holes in the solid ceiling, using a
suitable 8 mm helical drill bit and insert the
plugs provided. It is sufficient to drill the
outer holes shown in figure 2 or figure 3; the
inner holes can be drilled after installing the
hood.
Adjust the excursion of the fixing brackets
according to the depth of the niche; min.
220mm, max. 400mm as, shown in Fig. 4.
Tighten strongly the fastening screws of the
brackets immediately after you placed them
into position.
Place the cooker hood in an established area
and fix it with the screws supplied (see fig. 5).
Perform the holes into the ceiling in corre-
spondence of the central holes of the brack-
ets and fix definitively the product by apply-
ing the remaining screws.
Make the electrical connection (see fig. 6)
and connect the air discharge pipe following
the instructions given in the related section
DUCTING SYSTEMS.
If installing an SLT 955 MODUL LIGHT or
SLT 956 MODUL LIGHT, connect the elec-
trical wire of the MODUL LIGHT hood to the
connectors shown in figure 6 on SLT955 or
SLT956.
Install the plasterboard sheet making sure
that it fits perfectly to the metal edge of the
hood (Fig 12).
The dimensions of the hole to make in the
plasterboard are:
- SLT955: 502 mm X 502 mm with two
curved sides R551,
- SLT956: 982 mm X 222 mm, use the drill-
ing template provided.
Use the 3.5 x 22 screws supplied to fix the
plasterboard to the cooker hood and insert
them using the appropriate hole template.
We recommend at least 12 screws to obtain
a good fixation.
In case the hood is provided with an internal
panel be covered in plasterboard, wood or
other material, make a sheet of the following
dimensions:
- SLT955: 448 mm X 448 mm with R524 on
the corners,
- SLT956: 928 mm X 168 mm, use the drill-
ing template supplied.
Install the sheet to the panel (fig. 7), using
the screws provided in the case of plaster-
board or using the appropriate adhesive for
the type of material to be secured.
Caution: Do not use screws longer than the
panel thickness, maximum 3.5 x 22.
The product is not equipped with the duction
motor, therefore it must be coupled to a suc-
tion unit (remote motor) of the same manu-
facturer.
12
USE
INSTALLATION
To install the product is necessary to make
a countertop minimum depth of at least 220
mm up to a maximum of 400 mm. For great-
er depths it is necessary to ask the special
KIT with mounting brackets for ceiling depth
from 400mm to 580mm.
Attention: If a remote motor is installed
in the same compartment as products
SLT955/SLT956, check the overall dimen-
sions of the remote motor.
You can choose the side of the hood from
which to run off the sucked air; there are air
outlets of rectangular shape on three sides
of the hood.
After choosing the best location, set up the
channel, the supply provided includes an air
outlet flange of rectangular shape 230x80mm
to be installed on the chosen outlet. Leave
closed the air exhaust holes are not used.
There is also a fitting included, that allows
the use of tubes with a diameter equal to 150
mm (see fig. 1), if you plan to create a circular
air outlet duct.
Identify a reference point compared to the
exact centre for hood installation in the solid
ceiling. Then mark out the area for the holes
to be drilled, at the points shown in figure
2 for the item SLT955 or fig. 3 for the item
SLT956.
Make the holes in the solid ceiling, using a
suitable 8 mm helical drill bit and insert the
plugs provided. It is sufficient to drill the
outer holes shown in figure 2 or figure 3; the
inner holes can be drilled after installing the
hood.
Adjust the excursion of the fixing brackets
according to the depth of the niche; min.
220mm, max. 400mm as, shown in Fig. 4.
Tighten strongly the fastening screws of the
brackets immediately after you placed them
into position.
Place the cooker hood in an established area
and fix it with the screws supplied (see fig. 5).
Perform the holes into the ceiling in corre-
spondence of the central holes of the brack-
ets and fix definitively the product by apply-
ing the remaining screws.
Make the electrical connection (see fig. 6)
and connect the air discharge pipe following
the instructions given in the related section
DUCTING SYSTEMS.
If installing an SLT 955 MODUL LIGHT or
SLT 956 MODUL LIGHT, connect the elec-
trical wire of the MODUL LIGHT hood to the
connectors shown in figure 6 on SLT955 or
SLT956.
Install the plasterboard sheet making sure
that it fits perfectly to the metal edge of the
hood (Fig 12).
The dimensions of the hole to make in the
plasterboard are:
- SLT955: 502 mm X 502 mm with two
curved sides R551,
- SLT956: 982 mm X 222 mm, use the drill-
ing template provided.
Use the 3.5 x 22 screws supplied to fix the
plasterboard to the cooker hood and insert
them using the appropriate hole template.
We recommend at least 12 screws to obtain
a good fixation.
In case the hood is provided with an internal
panel be covered in plasterboard, wood or
other material, make a sheet of the following
dimensions:
- SLT955: 448 mm X 448 mm with R524 on
the corners,
- SLT956: 928 mm X 168 mm, use the drill-
ing template supplied.
Install the sheet to the panel (fig. 7), using
the screws provided in the case of plaster-
board or using the appropriate adhesive for
the type of material to be secured.
Caution: Do not use screws longer than the
panel thickness, maximum 3.5 x 22.
The product is not equipped with the duction
motor, therefore it must be coupled to a suc-
tion unit (remote motor) of the same manu-
facturer.
12
USE
INSTALLATION
To install the product is necessary to make
a countertop minimum depth of at least 220
mm up to a maximum of 400 mm. For great-
er depths it is necessary to ask the special
KIT with mounting brackets for ceiling depth
from 400mm to 580mm.
Attention: If a remote motor is installed
in the same compartment as products
SLT955/SLT956, check the overall dimen-
sions of the remote motor.
You can choose the side of the hood from
which to run off the sucked air; there are air
outlets of rectangular shape on three sides
of the hood.
After choosing the best location, set up the
channel, the supply provided includes an air
outlet flange of rectangular shape 230x80mm
to be installed on the chosen outlet. Leave
closed the air exhaust holes are not used.
There is also a fitting included, that allows
the use of tubes with a diameter equal to 150
mm (see fig. 1), if you plan to create a circular
air outlet duct.
Identify a reference point compared to the
exact centre for hood installation in the solid
ceiling. Then mark out the area for the holes
to be drilled, at the points shown in figure
2 for the item SLT955 or fig. 3 for the item
SLT956.
Make the holes in the solid ceiling, using a
suitable 8 mm helical drill bit and insert the
plugs provided. It is sufficient to drill the
outer holes shown in figure 2 or figure 3; the
inner holes can be drilled after installing the
hood.
Adjust the excursion of the fixing brackets
according to the depth of the niche; min.
220mm, max. 400mm as, shown in Fig. 4.
Tighten strongly the fastening screws of the
brackets immediately after you placed them
into position.
Place the cooker hood in an established area
and fix it with the screws supplied (see fig. 5).
Perform the holes into the ceiling in corre-
spondence of the central holes of the brack-
ets and fix definitively the product by apply-
ing the remaining screws.
Make the electrical connection (see fig. 6)
and connect the air discharge pipe following
the instructions given in the related section
DUCTING SYSTEMS.
If installing an SLT 955 MODUL LIGHT or
SLT 956 MODUL LIGHT, connect the elec-
trical wire of the MODUL LIGHT hood to the
connectors shown in figure 6 on SLT955 or
SLT956.
Install the plasterboard sheet making sure
that it fits perfectly to the metal edge of the
hood (Fig 12).
The dimensions of the hole to make in the
plasterboard are:
- SLT955: 502 mm X 502 mm with two
curved sides R551,
- SLT956: 982 mm X 222 mm, use the drill-
ing template provided.
Use the 3.5 x 22 screws supplied to fix the
plasterboard to the cooker hood and insert
them using the appropriate hole template.
We recommend at least 12 screws to obtain
a good fixation.
In case the hood is provided with an internal
panel be covered in plasterboard, wood or
other material, make a sheet of the following
dimensions:
- SLT955: 448 mm X 448 mm with R524 on
the corners,
- SLT956: 928 mm X 168 mm, use the drill-
ing template supplied.
Install the sheet to the panel (fig. 7), using
the screws provided in the case of plaster-
board or using the appropriate adhesive for
the type of material to be secured.
Caution: Do not use screws longer than the
panel thickness, maximum 3.5 x 22.
The product is not equipped with the duction
motor, therefore it must be coupled to a suc-
tion unit (remote motor) of the same manu-
facturer.
Connect the external motor’s cable to the
terminal board found in side the plastic box
of the wiring . Make sure to respect the colors
of cables when perfor ming the electrical con
nection (g.6).
Ret the grease lter and close the glass pa
nels.
12
PANEL OPENING DUCTING SYSTEMS
Open the panel by pulling it from the side
where the speed indicator of the extraction
motor is (Fig. 8). Accompany the panel with
your hands during the opening.
Following the panel opening, you can access
the grease filter and after its removal, acting
on the appropriate handle, you can reach the
seat of the charcoal filter (fig. 9).
To close the panel, simply bring it in hori-
zontal position until it the automatic closing
coupling occurs.
It is possible to install a main cooker hood with a
further one or two MODULES SLT955 - SLT956
in a single extraction system and then connect it
to a single, internal or external, remote extraction
motor of the home.
An extraction system, formed of more than one
element, is controlled by a single remote con-
trol because only a main cooker hood SLT955 or
SLT956 has all the electronic components nec-
essary for the functioning, whilst the remaining
MODULES SLT955 or SLT956 are dependent on
the main cooker hood SLT955 or SLT956.
Other combinations can also be realised between
products SLT955 and SLT956 because only one
main cooker hood (SLT955 or SLT956) is present
and two modules at the maximum.
A minimum distance of at least 110 mm is recom-
mended between the openings of the plasterboard
(Fig. 15) and a maximum distance of 1,000 mm.
A B C
13
EXTRACTION VERSIONS:
A: SLT955/SLT956 ............................................................................... remote motor SEM1-8*
B: SLT955/SLT956 + 1 x SLT955/SLT956 module......................................remote motor SEM8
C: SLT955/SLT956 + 2 x SLT955/SLT956 module......................................remote motor SEM8
D: SLT955/SLT956............................................................................... remote motor SEM2-7*
E: SLT955/SLT956 + 1 x SLT955/SLT956 module ..................................... remote motor SEM7
F: SLT955/SLT956 + 2 x SLT955/SLT956 module ..................................... remote motor SEM7
FILTER VERSIONS:
G: SLT955/SLT956............................................... remote motor SEM1-8* + air deviator S-DF2
H: SLT955/SLT956 + 1 or 2 x SLT955/SLT956 modules . remote motor SEM8 + air deviator S-DF2
*High performance
D E F
G H
Other manuals for SLT955
1
This manual suits for next models
1
Table of contents
Other Sirius Satellite Radio Ventilation Hood manuals
Sirius Satellite Radio
Sirius Satellite Radio SLTC EM 107 G900 User manual
Sirius Satellite Radio
Sirius Satellite Radio SLT955 Quick start guide
Sirius Satellite Radio
Sirius Satellite Radio SLT105 Quick start guide
Sirius Satellite Radio
Sirius Satellite Radio S900 User manual
Sirius Satellite Radio
Sirius Satellite Radio SU35 TC User manual
Sirius Satellite Radio
Sirius Satellite Radio SLTC 111 Quick start guide
Sirius Satellite Radio
Sirius Satellite Radio SLT950 EM Quick start guide
Sirius Satellite Radio
Sirius Satellite Radio SL906 L 1500 Quick start guide
Sirius Satellite Radio
Sirius Satellite Radio SL906 Series User manual
Sirius Satellite Radio
Sirius Satellite Radio SDD2ELEMTC Series User manual
Sirius Satellite Radio
Sirius Satellite Radio ALFRESCO SLEM80 User manual
Sirius Satellite Radio
Sirius Satellite Radio SLEM83 User manual
Sirius Satellite Radio
Sirius Satellite Radio SL906 DL Series User manual
Sirius Satellite Radio
Sirius Satellite Radio SLT960 Quick start guide
Sirius Satellite Radio
Sirius Satellite Radio STL969 Operating and maintenance manual
Sirius Satellite Radio
Sirius Satellite Radio SU900 User manual
Sirius Satellite Radio
Sirius Satellite Radio S-DDH3 Quick start guide
Sirius Satellite Radio
Sirius Satellite Radio SUT951 User manual
Sirius Satellite Radio
Sirius Satellite Radio SM923 52 Quick start guide
Sirius Satellite Radio
Sirius Satellite Radio SDD2EMIX60 User manual
Popular Ventilation Hood manuals by other brands
Miele
Miele DA 249-3 Operating and installation instructions
Event
Event EV-6UCQ installation guide
Hoover
Hoover HV-C60RU quick start guide
Electrolux
Electrolux Ventilation Hood Instruction book
Franke
Franke FCH 906 Instructions for use and installation
Thermador
Thermador PROFESSIONAL PH30HS Use and care guide
Epoq
Epoq FNO 605 BK EPOQ user manual
Gorenje
Gorenje STARCK S3 WHI941ST manual
Fisher & Paykel
Fisher & Paykel HC90PCX1 user guide
Condari
Condari QASAIR H Series Installation & user's instructions
GLOBALO
GLOBALO QAUDRO ISOLA 40 Operating and installation instructions
Electrolux
Electrolux EI30DD10KS Use and care guide
