ENDA ATC9311
ANALOG THERMOSTAT with DIGITAL DISPLAY
Plastic injection presses, automatic bread making ovens, nylon bag machines, shrink
packing machines, furniture presses, industrial ovens, textile machines, ironing
presses and other temperature control applications.
Applications
* 96 x 96mm sized.
* Digital display for measured temperature and set value.
* Selectable On-Off or time proportional control.
* Fe-Const thermocouple or NiCr-Ni thermocouple input.
* Output relay is de-energized in the case of sensor failure.
* Easy setting procedure.
* CE marked according to European Norms.
Dimensions
Flush
mounting
adaptor
Rubber
packing
Panel
Panel cut-out
Note:
1/2
Panel thickness
should be
max. 10mm.
105mm
99mm
90.5mm
90.5mm
Read this document carefully before using this device. The guarantee will be expired
by damaging of the device if you don't attend to the directions in the user manual. Also
we don't accept any compensations for personal injury, material damage or capital
disadvantages.
For removing mounting clamps :
Push out the flush-mounting clamp in direction 1 as shown in the figure above. Then, pull out the clamp
in direction 2. If there is no 60mm free space at back side of the device, it would be difficult to remove it
from the panel.
200
250
400
300
350
100
150
50
0
°C
ENDA ATC9311
OUT
SET
Temperature setting
knob
Control output state LED
(Light is on when control output is energized) Set key
Temperature display
96mm
99mm
1
OUT
200
250
150 °C
300100
35050
4000
ENDA ATC9311
SET
Technical Specifications
Supply 230V AC +10% -20%, 50/60Hz or 24V AC 10%, 50/60Hz or optional
9-30V DC / 7-24V AC 10% SMPS module.
±
±
Power consumption Max. 5VA
2.5mm² screw-terminal connection.
Wiring
HOUSING
Housing type Suitable for flush-panel mounting.
Dimensions W96xH96xD50mm
Weight Approx. 250g (after packing)
Enclosure material Self extinguishing plastics
CONTROL
Control type Single-setpoint control
On-Off / time proportional (optional)
Control algorithm
A/D converter 10 bits
Proportional band
Control period
Hysteresis
2% (for time proportional control)
10 second (for time proportional control)
4°C (for On-Off control)
OUTPUT
Control output Relay : 250V AC, 8A (for resistive load), NO+NC or 12V DC 20mA logic output
Mechanical 30.000.000 operation; electrical 300.000 operation
Life expectancy for relay
0 ... 400°C
1°C
For adjustment 4%, for display 0,5% (of full scale) or 1 digit.± ± ±
3 digits, 7.6mm, 7 segment red LED
Scale
Sensitivity
Accuracy
Display
Data retention
EMC
Safety requirements
EN 61326-1: 2013
EEPROM (at least 10 years)
EN 61010-1: 2010 (Pollution degree 2, overvoltage category II)
ENVIRONMENTAL CONDITIONS
Height Max. 2000m
Ambient/storage temperature
Max. relative humidity
0 ... +50°C/-25... +70°C
Rated pollution degree According to EN 60529 Front panel : IP60
Rear panel : IP20
Do not use the device in locations subject to corrosive and flammable gases.
While cleaning the device, solvents (thinner, gasoline, acid etc.) or corrosive materials must not be used.
ELECTRICAL CHARACTERISTICS
Depth
50mm
14mm
57mm
2
Thank you for choosing ENDA ATC9311
80% Relative humidity for temperatures up to 31°C, decreasing linearly to 50% at 40°C.
SİSEL MÜHENDİSLİK ELEKTRONİK SAN. VE TİC. A.Ş.
Şerifali Mah. Y.Dudullu 34775
ÜMRANİYE/İSTANBUL-TURKEY
Tel : +90 216 499 46 64 Pbx. Fax : +90 216 365 74 01
url : www.enda.com.tr
Barbaros Cad. No:18 ENDA
TM
ATC9311-EN-07-170814
