Sistemalux MINI LOOK User manual

INS-325
9320 Boul. St-Laurent, suite 100, Montréal (Québec) Canada H2N 1N7
P.: 514.523.1339 F.: 514.525.6107 www.sistemalux.com
JP - R5Last update: January 29, 2020
IMPORTANT - READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES, BY A PERSON FAMILIAR WITH THE
CONSTRUCTION AND OPERATION OF THE PRODUCT, AND THE HAZARDS INVOLVED. PROPER GROUNDING IS REQUIRED FOR SAFETY.
MINI LOOK / MINI COOL WALL
MODELS : S7201, S7202, S7231, SL9201, SL9202, SL9231
INSTRUCTIONS SHEET PAGE: 1 of 4
C
#8 SCREWS
(NOT INCLUDED)
DIRECT FEED INSTALLATION (DF) - LOW VOLTAGE (24V) REMOTE DRIVER (REM)
DISCONNECT THE MAIN LINE BEFORE WIRING SECONDARY CONNECTORS.
A- PREPARE SURFACE FOR INSTALLATION (SEE DIMENSIONS BELOW). *INSERT (2) ANCHOR SCREWS (NOT INCLUDED) IF NECESSARY.
B- UNFASTEN THE SET SCREWS WITH AN ALLEN KEY (INCLUDED) TO REMOVE THE FIXTURE FROM THE BASE.
DO NOT COMPLETELY REMOVE THE SET SCREWS.
C- INSTALL THE FIXTURE BASE TO THE WALL USING APPROPRIATE #8 SCREWS (NOT INCLUDED).
D- MAKE WIRE CONNECTIONS USING THE CONNECTOR. BE SURE TO FULLY PRESS THE BUTTONS TO CONNECT.
E- FASTEN THE FIXTURE BACK ON ITS BASE WITH THE SET SCREWS USING AN ALLEN KEY (INCLUDED).
BLACK
LED -
RED
LED +
D + E
FIXTURE
CONNECTOR
SET SCREWS
ALLEN KEY
(INCLUDED)
E
D
3.31"
(84mm)
6.69"
(170mm)
FEED
POSITION
A B
*ANCHOR
SCREWS
(NOT INCLUDED)
SET SCREWS
FIXTURE
FIXTURE
BASE
ALLEN KEY
(INCLUDED)

INS-325
9320 Boul. St-Laurent, suite 100, Montréal (Québec) Canada H2N 1N7
P.: 514.523.1339 F.: 514.525.6107 www.sistemalux.com
JP - R5Last update: January 29, 2020
MINI LOOK / MINI COOL WALL
MODELS : S7201, S7202, S7231, SL9201, SL9202, SL9231
INSTRUCTIONS SHEET PAGE: 2 of 4
UNIVERSAL
CROSSBAR
PHILLIPS SCREWS
(INCLUDED)
DRIVER
UNIVERSAL
CROSSBAR
PHILLIPS SCREWS
(INCLUDED)
MOUNTING
PLATE
JUNCTION
BOX
OR
CROSSBAR ALIGNMENT
HORIZONTAL VERTICAL
4" JUNCTION BOX INSTALLATION (JB) - INTEGRAL DRIVER 120-277V (UNV)
A- MAKE WIRE CONNECTIONS (FOLLOWING POLARITY MARKING) USING WATERTIGHT TWIST CONNECTORS (NOT INCLUDED) AND INSERT
THE DRIVER IN THE JUNCTION BOX. FOR PROPER FIXTURE ORIENTATION, SEE THE CROSSBAR ALIGNMENT BELOW.
B- FIX THE UNIVERSAL CROSSBAR TO THE 4" JUNCTION BOX USING (2) PHILLIPS SCREWS (INCLUDED).
C- INSTALL THE MOUNTING PLATE ON THE UNIVERSAL CROSSBAR USING (2) PHILLIPS SCREWS (INCLUDED).
D- UNFASTEN (2) SET SCREWS WITH AN ALLEN KEY (INCLUDED) TO REMOVE THE BASE FROM THE FIXTURE.
DO NOT COMPLETELY REMOVE THE SCREWS.
E- FASTEN THE FIXTURE BASE ON THE MOUNTING PLATE USING (2) PHILLIPS SCREWS (INCLUDED).
F- MAKE WIRE CONNECTIONS USING THE CONNECTOR. BE SURE TO FULLY PRESS THE BUTTONS TO CONNECT.
G- FASTEN THE FIXTURE BACK ON ITS BASE WITH THE SET SCREWS USING AN ALLEN KEY (INCLUDED).
D
C
A + B
WATERTIGHT
TWIST CONNECTORS
(NOT INCLUDED)
E + F + G
MOUNTING
PLATE
FIXTURE
BASE
FIXTURE
SET SCREWS
ALLEN KEY
(INCLUDED)
CONNECTOR
BLACK
LED -
RED
LED +
F
E
G
C
B
PHILLIPS SCREWS
(INCLUDED)
SET SCREWS
FIXTURE
FIXTURE
BASE
ALLEN KEY
(INCLUDED)

INS-325
9320 Boul. St-Laurent, suite 100, Montréal (Québec) Canada H2N 1N7
P.: 514.523.1339 F.: 514.525.6107 www.sistemalux.com
JP - R5Last update: January 29, 2020
MINI LOOK / MINI COOL WALL
MODELS : S7201, S7202, S7231, SL9201, SL9202, SL9231
INSTRUCTIONS SHEET PAGE: 3 of 4
4" JUNCTION BOX INSTALLATION (JB) - LOW VOLTAGE (24V) REMOTE DRIVER (REM)
A- FIX THE UNIVERSAL CROSSBAR TO THE 4" JUNCTION BOX USING (2) PHILLIPS SCREWS (INCLUDED).
FOR PROPER FIXTURE ORIENTATION, SEE THE CROSSBAR ALIGNMENT BELOW.
B- INSTALL THE MOUNTING PLATE ON THE UNIVERSAL CROSSBAR USING (2) PHILLIPS SCREWS (INCLUDED).
C- UNFASTEN (2) SET SCREWS WITH AN ALLEN KEY (INCLUDED) TO REMOVE THE BASE FROM THE FIXTURE.
DO NOT COMPLETELY REMOVE THE SCREWS.
D- FASTEN THE FIXTURE BASE ON THE MOUNTING PLATE USING (2) PHILLIPS SCREWS (INCLUDED).
E- MAKE WIRE CONNECTIONS USING THE CONNECTOR. BE SURE TO FULLY PRESS THE BUTTONS TO CONNECT.
F- FASTEN THE FIXTURE BACK ON ITS BASE WITH THE SET SCREWS USING AN ALLEN KEY (INCLUDED).
UNIVERSAL
CROSSBAR
PHILLIPS SCREWS
(INCLUDED)
UNIVERSAL
CROSSBAR
PHILLIPS SCREWS
(INCLUDED)
MOUNTING
PLATE
JUNCTION
BOX
OR
CROSSBAR ALIGNMENT
HORIZONTAL VERTICAL
C
AB
D + E + F
DISCONNECT THE MAIN LINE BEFORE WIRING SECONDARY CONNECTORS.
MOUNTING
PLATE
PHILLIPS SCREWS
(INCLUDED)
FIXTURE
BASE
FIXTURE
SET SCREWS
ALLEN KEY
(INCLUDED)
CONNECTOR
BLACK
LED -
RED
LED +
E
D
F
SET SCREWS
FIXTURE
FIXTURE
BASE
ALLEN KEY
(INCLUDED)

INS-325
9320 Boul. St-Laurent, suite 100, Montréal (Québec) Canada H2N 1N7
P.: 514.523.1339 F.: 514.525.6107 www.sistemalux.com
JP - R5Last update: January 29, 2020
MINI LOOK / MINI COOL WALL
MODELS : S7201, S7202, S7231, SL9201, SL9202, SL9231
INSTRUCTIONS SHEET PAGE: 4 of 4
OR
JUNCTION BOX ALIGNMENT
HORIZONTAL VERTICAL
D + E
PHILLIPS SCREWS
(INCLUDED)
MOUNTING
PLATE
2" JUNCTION BOX INSTALLATION (J2) - LOW VOLTAGE (24V) REMOTE DRIVER (REM)
DISCONNECT THE MAIN LINE BEFORE WIRING SECONDARY CONNECTORS.
C
A B
JUNCTION
BOX
A- INSTALL THE MOUNTING PLATE ON THE 2" JUNCTION BOX USING (2) PHILLIPS SCREWS (INCLUDED).
B- UNFASTEN THE (2) SET SCREWS WITH AN ALLEN KEY (INCLUDED) TO REMOVE THE BASE FROM THE FIXTURE.
DO NOT COMPLETELY REMOVE THE SCREWS.
C- FASTEN THE FIXTURE BASE ON THE MOUNTING PLATE USING (2) PHILLIPS SCREWS (INCLUDED).
D- MAKE WIRE CONNECTIONS USING THE CONNECTOR. BE SURE TO FULLY PRESS THE BUTTONS TO CONNECT.
E- FASTEN THE FIXTURE BACK ON ITS BASE WITH THE SET SCREWS USING AN ALLEN KEY (INCLUDED).
FIXTURE
SET SCREWS
ALLEN KEY
(INCLUDED)
CONNECTOR
BLACK
LED -
RED
LED +
E
D
MOUNTING
PLATE FIXTURE
BASE
PHILLIPS SCREWS
(INCLUDED)
SET SCREWS
FIXTURE
FIXTURE
BASE
ALLEN KEY
(INCLUDED)