Sistemalux MOAI User manual

A- PREPARE THE DESIRED DRAINING USING GRAVEL UNDER THE FLANGE.
B- INSTALL AN APPROPRIATE ELECTRICAL CONDUIT (NOT INCLUDED) THROUGH THE FLANGE.
C- FEED CABLE THROUGHT THE ELECTRICAL CONDUIT.
D- POUR CONCRETE IN AND MAKE SURE THAT IT IS LEVELED AD IT SITS 5MM UNDER THE TOP OF THE FLANGE
E- REMOVE THE PROTECTION PAPER BEFORE INSTALLING BASE.
D
A + B + C
NEW CONCRETE INSTALLATION PREPARATION (WITH FLANGE ACCESSORY S5310, S6309)
MOAI
BOLLARD S6150, S6160
INSTRUCTIONS SHEET PAGE: 1 of 4
INS-818
9320 Boul. St-Laurent, suite 100, Montréal (Québec) Canada H2N 1N7
P.: 514.523.1339 F.: 514.525.6107 www.sistemalux.com
DM - R2Last update: December 13, 2021
IMPORTANT - READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES, BY A PERSON FAMILIAR WITH THE
CONSTRUCTION AND OPERATION OF THE PRODUCT, AND THE HAZARDS INVOLVED. PROPER GROUNDING IS REQUIRED FOR SAFETY.
LIGHT DIRECTION
OK NO! NO!
5mm
E
∅ 7" (178mm)
9 1/2" (241mm)
∅ 4 3/4"(118 mm)
6 1/2" (165mm)
S5310 S6309

MOAI
BOLLARD S6150, S6160
INSTRUCTIONS SHEET PAGE: 2 of 4
INS-818
9320 Boul. St-Laurent, suite 100, Montréal (Québec) Canada H2N 1N7
P.: 514.523.1339 F.: 514.525.6107 www.sistemalux.com
DM - R2Last update: December 13, 2021
BOLLARD BASE
BOLLARD BODY
FIXTURE INSTALLATION INTEGRAL DRIVER (120-277V) DIMMING 0-10V
F- UNFASTEN THE (4) SCREWS AT BOTTOM OF BOLLARD USING THE ALLEN KEY (INCLUDED).
G- REMOVE THE BOLLARD BODY FROM THE BOLLARD BASE.
H- LOWER THE BOLLARD BASE ON THE FLANGE AND FIX IT TIGHTLY WITH APPROPRIATE SCREWS AND WASHERS (NOT INCLUDED)
1/4-20 or M6 NUT
(NOT INCLUDED)
FLANGE
F G
H
NEW CONCRETE INSTALLATION PREPARATION (WITH FLANGE ACCESSORY S5310, S6309)

MOAI
BOLLARD S6150, S6160
INSTRUCTIONS SHEET PAGE: 3 of 4
INS-818
9320 Boul. St-Laurent, suite 100, Montréal (Québec) Canada H2N 1N7
P.: 514.523.1339 F.: 514.525.6107 www.sistemalux.com
DM - R2Last update: December 13, 2021
NOT INCLUDED
A- MAKE HOLE IN CONCRETE SURFACE OR OTHER. USE ANCHORS IF NECESSARY (4X TYP.NOT INCLUDED)
B- UNFASTEN THE 4 SCREWS AT THE BOTTOM OF BOLLARD USING ALLEN KEY (INCLUDED)
C- REMOVE BOLLARD BODY FROM BOLLARD BASE
D- FASTEN BOLLARD BASE TO LEVELED SURFACE USING (4X TYP.) SCREWS (NOT INCLUDED)
PRE-EXISTING SURFACE INSTALLATION PREPARATION
CONCRETE BASE
BOLLARD BASE
BOLLARD BODY
A B
CD

MOAI
BOLLARD S6150, S6160
INSTRUCTIONS SHEET PAGE: 4 of 4
INS-818
9320 Boul. St-Laurent, suite 100, Montréal (Québec) Canada H2N 1N7
P.: 514.523.1339 F.: 514.525.6107 www.sistemalux.com
DM - R2Last update: December 13, 2021
A- MAKE THE NECESSARY WIRE CONNECTIONS (SEE WIRING DIAGRAM) USING WATERTIGHT CONNECTORS (NOT INCLUDED)
B- FASTEN THE BOLLARD BODY BACK ON ITS BASE USING THE (4) SCREWS WITH THE ALLEN KEY (INCLUDED).
SCREW
A
A
WATERTIGHT
CONNECTOR
(NOT INCLUDED)
WIRING DIAGRAM
FIXTURE CABLES
LIVE
(black)
NEUTRAL
(white)
DIM +
(red)
DIM -
(brown)
DIMMING 0-10V (D10)
120-277V
GROUND
(green)
WATERTIGHT
CONNECTOR
(NOT INCLUDED)
OR
***COVER DIMMING
CABLES IF NOT USING
FIXTURE INSTALLATION INTEGRAL DRIVER 120-277V (UNV) DIMMING 0-10V (D10)
A+B