Sistemalux S1920 User manual

OVER-ALL
MODEL : S1920, S1921, S1925 / S1900, S1901, S1905 / S1910, S1911, S1915
INSTRUCTIONS SHEET PAGE: 1 of 4
INS-508
9320 Boul. St-Laurent, suite 100, Montréal (Québec) Canada H2N 1N7
P.: 514.523.1339 F.: 514.525.6107 www.sistemalux.com
CL - R0Last update: December 07, 2020
A
C
A- UNCLIP THE FIXTURE FROM ITS BASE USING THE WEDGE TOOL (INCLUDED).
B- USING THE HOLES ON THE FIXTURE BASE, PREPARE SURFACE FOR INSTALLATION.
C- INSTALL (3) ANCHORS (NOT INCLUDED) INTO THE SURFACE.
GROUND INSTALLATION
REMOTE DRIVER (REM)
IMPORTANT - READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES, BY A PERSON FAMILIAR WITH THE
CONSTRUCTION AND OPERATION OF THE PRODUCT, AND THE HAZARDS INVOLVED. PROPER GROUNDING IS REQUIRED FOR SAFETY.
B
CONDUIT
WEDGE TOOL
(INCLUDED)
CONDUIT
ANCHORS
(NOT INCLUDED)
FIXTURE
HEAD
FIXTURE
BASE
FIXTURE BASE
B
3
⁄
16"
(5,20mm)
MICRO
¼ "
(6,30mm)
MINI
¼ "
(6,30mm)
OVER-ALL
MODEL
B

OVER-ALL
MODEL : S1920, S1921, S1925 / S1900, S1901, S1905 / S1910, S1911, S1915
INSTRUCTIONS SHEET PAGE: 2 of 4
INS-508
9320 Boul. St-Laurent, suite 100, Montréal (Québec) Canada H2N 1N7
P.: 514.523.1339 F.: 514.525.6107 www.sistemalux.com
CL - R0Last update: December 07, 2020
D
D- FASTEN THE FIXTURE BASE TO THE SURFACE, USING (3) SCREWS (NOT INCLUDED) (FOLLOW SCREW SIZE TABLE).
E- PASS THE FIXTURE CABLE THROUGH THE CABLE OUTLET AND CONDUIT AND
MAKE ALL NECESSARY CONNECTIONS.
(FOLLOWING WIRING DIAGRAM).
F- CLIP THE FIXTURE HEAD TO THE BASE. FOR ALIGNMENT, REFER TO THE ARROWS ON THE FIXTURE HEAD AND BASE.
CLICK
E + F
SCREWS
(NOT INCLUDED)
(SEE BOARD MODEL SCREW)
FIXTURE BASE
FIXTURE HEAD
FIXTURE CABLE
CONDUIT
F
E
LED +
LED -
RED
BLACK
SCREW
10-32
¼"-20
¼"-20
MICRO
MODEL
SCREW SIZE
MINI
OVER-ALL
CABLE OUTLET

OVER-ALL
MODEL : S1920, S1921, S1925 / S1900, S1901, S1905 / S1910, S1911, S1915
INSTRUCTIONS SHEET PAGE: 3 of 4
INS-508
9320 Boul. St-Laurent, suite 100, Montréal (Québec) Canada H2N 1N7
P.: 514.523.1339 F.: 514.525.6107 www.sistemalux.com
CL - R0Last update: December 07, 2020
GROUND INSTALLATION ON STAKE
REMOTE DRIVER (REM)
A- UNCLIP THE FIXTURE FROM ITS BASE USING THE WEDGE TOOL (INCLUDED).
B- 1- USE A RUBBER MALLET TO INSERT THE STAKE INTO THE GROUND.
2- INSERT THE STAKE TO THE FIRST DISC TO INSURE A LEVELED POSITION WITH THE GROUND.
C- ALIGN THE (4) FIXING HOLES UNDER THE FIXTURE BASE TO THE TOP OF THE STAKE.
D- FEED THE CABLE THROUGH THE STAKE’S CABLE ENTRY HOLE AND USE (4) HEX SCREW (INCLUDED) OR (1) HEX SCREW (INCLUDED)
TO SECURE THE FIXTURE ON THE STAKE. USE THE CABLE LOCK (INCLUDED) TO LOCK THE CABLE TO THE STAKE.
A B
WEDGE TOOL
(INCLUDED)
FIXTURE HEAD
FIXTURE
BASE
FIXTURE HEAD
FIXTURE HEAD
FIXTURE
CABLE
HEX SCREWS
(INCLUDED)
HEX SCREW
(INCLUDED)
FIXTURE
BASE
STAKE
12
RUBBER
MALLET
CABLE LOCK
MINI AND OVER-ALL
MODEL
MICRO OVER-ALL
MODEL
FIXTURE
BASE
STAKE
C + D
C
D
C

OVER-ALL
MODEL : S1920, S1921, S1925 / S1900, S1901, S1905 / S1910, S1911, S1915
INSTRUCTIONS SHEET PAGE: 4 of 4
INS-508
9320 Boul. St-Laurent, suite 100, Montréal (Québec) Canada H2N 1N7
P.: 514.523.1339 F.: 514.525.6107 www.sistemalux.com
CL - R0Last update: December 07, 2020
D- PASS THE FIXTURE CABLE TROUGH THE CONDUIT AND MAKE ALL NECESSARY CONNECTIONS (FOLLOWING WIRING DIAGRAM).
D
LED +
LED -
RED
BLACK
FIXTURE
CABLE
CONDUIT