Skoda AMUNDSEN+ User manual

SIMPLY CLEVER
Amundsen and Bolero infotainment
systems
Operating Instructions


3V0012720EA

Preface
This manual is intended for the Bolero and Amundsen infotainment systems (hereinafter referred to
only as Device).
Please read these Operating Instructions carefully, because the operation in accordance with these
instructions is a prerequisite for proper use of the unit.

3V0012720EA

Table of Contents
Operating Instructions 3
Notes 4
Abbreviations
Introductory information
Important notes 6
Equipment overview 7
Device operation and settings
Operation on the device screen 9
Voice control 11
Device Settings 14
Radio
Operation 17
Settings 20
Media
Operation 22
Audio sources 24
Images
Image viewer 28
Telephone
Introductory information 30
Pair and connect 31
Dial telephone number 34
Telephone functions 37
Text messages (SMS) 38
MirrorLink
MirrorLink ™39
Navigation (Amundsen)
Navigation description 42
New destination 43
My Destinations 44
POI 46
Import custom destinations 47
Map 48
Route guidance 50
Tour 53
Traffic reports 54
Settings 56
Vehicle systems
CAR - Vehicle Settings 58
Adjustment of the heating and cooling
system 63
Index
2Table of Contents

Operating Instructions
This manual is intended for the Bolero and Amundsen infotainment systems
(hereinafter referred to only as Device).
This Owner's Manual describes all possible device functions without identify-
ing them as special equipment, model variants or market-dependent equip-
ment. Consequently, the device on this vehicle does not need to contain all of
the functions described in this Owner's Manual.
The availability of some features described in this manual depends on the
type of external devices (for example, phone, music player, etc..).
Information on the compatibility of external devices can be found on ŠKODAIn-
ternet pages http://infotainment.skoda-auto.com .
The Images in these Operating Instructions are for illustrative purposes only.
The illustrations can differ in minor details from your vehicle; they are only in-
tended to provide general information.
ŠKODA AUTO a.s. pursues a policy of ongoing product and model development
with all vehicles. Changes in terms of supply scope are possible at any time
with regard to design, equipment and technology. The information listed in
these Operating Instructions corresponds to the information available at the
time of going to press.
It is therefore not possible for legal claims to be made based on the technical
data, illustrations and information contained in these Operating Instructions.
Declaration of conformity
ŠKODA AUTO a.s. hereby declares that the ŠKODA Infotainment systems meet
the basic requirements and additional provisions of Directive 1999/5/EC with
reference to radio equipment and telecommunications devices.
ŠKODA AUTO a.s. hereby declares that the “connection and the use of this
communication device is granted by the Nigerian Communications Commis-
sion.”
3
Operating Instructions

Notes
Structure of these Operating Instructions
The Operating Instructions are hierarchically divided into the following areas.
■Main chapters (e.g. Introductory information) - the title of the main chapter is
always shown on the lower right side of the page
■Chapter (e.g. Equipment overview)
■ Introduction to the topic - Module overview within the chapter, intro-
ductory information about the chapter content, if necessary, applies to all
chapter notes
■Module (for example, Switching the unit on/off)
Text notes
Note Meaning
“Press” Short press of the button for under 1 s.
“Hold” Long press of the button for 2 - 5 s.
Text Symbols
Symbol Meaning
Reference to the introductory module of a chapter with im-
portant information and safety warnings.
Continuation of the module on the next page.
®Trademark.
™
→Marker to the next operation step.
The text symbol used for the right control dial
WARNING
Texts with this symbol draw attention to threats of a serious accident, in-
jury or loss of life.
CAUTION
Texts with this symbol draw attention to the risk of vehicle damage or possible
inoperability of some systems.
Note
Texts with this symbol contain additional information.
Information search
When searching for information in the Operating Instructions, we recommend
using the Index at the end of the manual.
4Notes

Abbreviations
Abbreviation Definition
A2DP a Bluetooth® profile for the one-sided audio data transmis-
sion
AF Alternative frequencies for the current radio station
AM Identification of the radio-frequency range
TCS Traction Control of the drive wheels
AVRCP a Bluetooth® profile for the operation associated with the
transmission of audio data multimedia functions
BT Bluetooth® - wireless communication for reception and
transmission of voice and data information
DAB Digital radio reception
DRM a system for monitoring or restricting the use of digital me-
dia content
DTMF a dialling tone during a telephone communication
ESC Electronic Stability Control
FM Identification of the radio-frequency range
HFP a Bluetooth® - profile for communication between a mobile
telephone and the hands-free equipment in the vehicle
GPS Satellite system for determining the position
GPT method for the division of the areas in the data devices (to
be used for mass storage resources)
GSM a telephone service of mobile communication
ID3 tag an additional feature of a music file, which allows for the dis-
play of artist, title, album name, etc.
MAP a Bluetooth® - profile for the exchange of text messages
(SMS) between the device and a connected device
2D planar map display
3D spatial map display
mp3 compressed audio format
MTP a communication protocol for a data device
PI code a program identification of the tuned radio station, which al-
lows a group sort of radio stations
Abbreviation Definition
PIN personal identification number
RDS a system for the transmission of additional information for
FM radio reception
Messages a service for short text messages
TMC Traffic reports, which may affect the navigation
TP Identification of a traffic information station
VIN Vehicle identification number
wav compressed audio format
wma compressed audio format
5
Abbreviations

Introductory information
Important notes
Introduction
This chapter contains information on the following subjects:
Information on use, updating and compatibility 6
Component protection 6
WARNING
■Concentrate fully at all times on your driving! As the driver you are fully
responsible for the operation of your vehicle.
■Only use the device in such a way that you are in full control of your vehi-
cle in every traffic situation – there is the risk of accidents!
■Adjust the volume to ensure that acoustic signals from outside the vehi-
cle, e.g. sirens from emerging vehicles instructing you to give way to, such
as the police, ambulance and fire brigade, can be heard at all times.
■High volumes can cause hearing damage.
CAUTION
In some countries, some unit features can no longer be selected when the ve-
hicle is running faster than a certain speed. This is not a malfunction, but com-
plies with the national legal regulations.
Information on use, updating and compatibility
Read and observe and on page 6 first.
Refer to the ŠKODA Internet pages http://infotainment.skoda-auto.com for
information on the compatibility of external devices as well as software up-
dates and navigation data.
Component protection
Read and observe and on page 6 first.
Some electronic control units are equipped with protection components, which
serve as protective mechanisms, for example, in cases of theft of the ECUs.


When component protection is enabled, the following message appears on the
unit display Component theft protection: the infotainment system is not fully
available at present. Please switch on the ignition.
If the component protection does not activate by switching on the ignition,
please contact a ŠKODA specialist garage.
6Introductory information

Equipment overview
Introduction
This chapter contains information on the following subjects:
Description of the device 7
Touch screen 7
Turn device on/off 8
Unit menus 8
Adjusting the volume 8
This chapter covers the device, the switching on and off and volume control of
the device.
Description of the device
Fig. 1 Device Overview (Amundsen)
Key Bolero: Amundsen:
Control dial for calls and confirmations
1 - Left control dial for switching the device on and off; volume
adjustment
2 - Menu Radio » page 17
3 - Menu Media » page 22
4 - Menu Telephone » page 30
5 - Voice control » page 11
6 - Device Settings
» page 14
 - Menu Navigation
» page 42
7 - Sound settings
» page 14
 - Radio traffic service
» page 54
8 - Vehicle systems settings » page 58
9 - Unit menus display » page 8
10 Touch screen
Touch screen
The unit is equipped with a touch screen which can be operated with a light
touch or swipe of a finger.
The brightness level of the screen can be set » page 15.
CAUTION
Notes on operating the touch screen
■The screen is operated with a light touch of a finger. Do not exert any pres-
sure on the screen - there is a risk of damaging the screen!
■It is not possible to operate the screen with your fingernails or while wearing
gloves.
CAUTION
Notes on protecting and cleaning the screen
■To protect the screen, you can use a suitable screen protector for touchpads
that does not affect its functionality.
■Dirt can be removed from the screen by using a soft cloth and, if necessary,
methylated spirits.
7
Introductory information

Turn device on/off
Manual Power On/Off
›Press  to switch the device on or off.
Automatic Power On of the device
If the device was not turned off with the control switch  before the ignition
was turned off, it will automatically switch on after the ignition is switched on.
Automatic Power Off of the device
If the vehicle key is pulled out of the ignition lock while the unit is switched on,
the device will switch off automatically.
If the vehicle is fitted with the starter button, the device will switch off auto-
matically after the engine is switched off and the door is opened.
With the ignition off, the device will automatically turn off after about 30 mi-
nutes.
The device can turn off automatically under certain circumstances, in order to
protect it against the vehicle battery being discharged or for the protection of
the device.
The unit will inform you by one of the following messages on the screen.
›Warning: 12 V battery low. Please start the engine or switch off the info-
tainment system. - The vehicle battery is low, start the engine or turn the
unit off.
›12 V battery charge very low. The infotainment system will be switched off.
- The vehicle battery is discharged, the device switches itself off.
›Operating temperature not maintained. Switching off Infotainment system.
- The device temperature is too low or too high, the device switches itself
off.
Unit menus
Fig. 2
Unit menus
Call up the main menu
›Press the button  and the display shows the device menu » Fig. 2.
Overview of the function keys
Menu Radio » page 17
Menu Media » page 22
Menu Images » page 28
Settings Sound » page 14
Device Settings Setup » page 14
Vehicle system settings Vehicle » page 58
Menu Navigation (Amundsen) » page 42
Menu Phone » page 30
Display of TMC traffic reports Traffic (Amundsen) » page 54
Menu MirrorLink™ » page 39
Adjusting the volume
Every change in volume is displayed on the screen.
Increase volume
›Turn the control  to the right.
Decrease volume
›Turn the control  to the left.
Muting
›Adjust the volume by turning the control  to the left to 0. 










8Introductory information

or
›Press the button  .
The following symbol appears in the display when the sound is muted: ,
If at the time of muting a sound is made in the menu Media, then the playback
is interrupted (pause)1).
CAUTION
If the volume is too high sound resonance can occur in the vehicle which can
lead to damaged speakers.
Device operation and settings
Operation on the device screen
Introduction
This chapter contains information on the following subjects:
Operation 9
Alphanumeric with keyboard 10
This chapter covers the touch screen and its operation.
Operation
Fig. 3 Screen area / screen display
Description of the display
Status bar
Information and the operation of the current menu
Function keys of the current menu
Identification of the current menu
Return to the higher-level menu
Slider - Position and movement in the menu (movement is possible by
moving the slider down / up with the finger or by turning the control dial
 left or right)
Currently selected menu item (framed in green)
Menu item with “Checkbox”   
A
B
C
D
E
F
G
H
1) Does not apply to AUX.
9
Device operation and settings

Inactive menu item
Open a submenu of the menu item with the “pop-up window” 
Status line
In some menus a status bar located at the top of the screen shows the time
and outdoor temperature along with other information.
Function keys
Screen areas which confirm a function or a menu are called “function keys”.
White background - The button is active and thus selectable
Grey background - The button is inactive and thus not selectable
Green framing - Currently selected button on a function / menu
Selecting menu/menu item/function
›Drag your finger over the screen in the required direction.
›Turning the knob ,
Confirming menu/menu item/function
›by touching the function button with your finger.
›Press the wheel ,
Returning to higher-level menu
›by pressing the function key ,
›By touching the screen outside of the “pop-up window” with your finger.
›By pressing the corresponding button next to the screen (e.g. in the menu
Media by pressing the button  ).
Switching function with “Checkbox” on/off
› - Function is switched on
› - Function is switched off
Select the menu item / function value
› - Selected menu item / function value
› - Deselected menu / function value
Set value
›By pressing the function button with one of the following symbols . . . .
. ,
›Touching or moving your finger over the scale.
›Turning the knob ,
I
JAlphanumeric with keyboard
Fig. 4
Example of the keyboard display
The alphanumeric keypad is used to enter characters.
The device offers the possibility to select the keyboard display in alphabetical
order (ABC) or the QWERTY system » page 15, Setting the keyboard layout,
Description of the alphanumeric keyboard » Fig. 4
Input line
Context-dependent:
› - Switch to numbers
› - Switch to Latin letters
› - Switch to Cyrillic letters
Context-dependent:
› - Switch to capital letters
› - Switch to special characters
› - Switch to numbers
Return to the higher-level menu
Display of searched entries (the number of searched entries is displayed in
the button)
Confirmation of the entered number
Erase the entered characters
Toggle upper case to lower case and vice versa
Switching between keyboards with specific characters of the selected lan-
guages » page 15, Additional keypad language settings
Enters a blank
Move the cursor within the input line to the left
Move the cursor within the input line to the right
Search
While entering characters, a search is made for corresponding entries. 
A
B
C









10 Device operation and settings

The entry such as a telephone contact to be searched for must be entered
along with the special characters (diacritics).
By pressing the function key  a list of matching entries opens . If less than 5
entries were found, a list of the found entries opens automatically.
Voice control
Introduction
This chapter contains information on the following subjects:
Function requirements 11
Switching on/off 11
Instructions and help for voice control 12
Operation principle 12
not recognizing a voice command 12
Correction of a voice command input 13
Stop/restore voice command input 13
Voice commands not included in the help 13
Some equipment functions can be operated by using voice commands.
The voice control system can be used either by the driver or by the front pas-
senger.
This chapter covers the principles and conditions of the voice control system.
The manual and help for voice control will help you to familiarise yourself with
the operation and the possible voice commands. Voice commands, which are
not included in either the manual or in the help topics » page 13,
The voice control is available in the following menus.
›Radio
›Media
›Telephone
›Navigation
WARNING
do not use the function of the phone voice control in an emergency . Your
voice commands may not be recognized in such situations. The telephone
connection may not be established or the connection may take too much
time to complete. The emergency number should be dialled manually!
CAUTION
The messages are generated by the device. The flawless clarity (e.g. road or
city name) cannot always be guaranteed.
Function requirements
Read and observe and on page 11 first.
Function requirements for voice control.
The unit is switched on.
No phone call is in progress.
The parking aid is not active.
Requirements for optimum voice command recognition.
›Speak with a normal tone of voice without intonation and excessive pauses.
›Avoid bad pronunciation.
›Close the doors, windows and sliding roof, in order to avoid disturbing envi-
ronmental influences on the function of the voice commands.
›You are recommended to speak louder at higher speeds, so that the sound of
your voice is not drowned out by the increased ambient noise.
›During voice control, limit additional noise in the vehicle, e.g. passengers
talking at the same time.
CAUTION
■For some languages, there is no voice control available. This device indicates
this fact through a text message that is displayed after setting the device lan-
guage screen .
■In the menu Navigation it is necessary to spell city and street names if the
entered destination is located in a country that has no voice control available
for the language. The device indicates this through a text message on the
screen.
Note
During voice control, no navigation announcements and traffic announce-
ments are played.
Switching on/off
Read and observe and on page 11 first.
Switching on voice control
Voice control can be switched on in one of the following ways. 





11
Device operation and settings

›Press the button  on the device.
or
›Press  on the multifunction steering wheel.
Activation of voice control is indicated by an acoustic signal and the device
screen will display a collection of basic voice commands for the current menu.
Switching off voice control
Voice control can be switched off in one of the following ways.
›Hold the button  on the device or press twice.
›Press  on the multifunction steering wheel or press twice.
›Issue the voice command End voice control.
The voice control also turns itself off when you change to another menu (e.g.
Radio, Media etc.)
Instructions and help for voice control
Read and observe and on page 11 first.
The unit will play a tutorial for voice mode, which makes using the familiar
voice control operate the appliance you, or help with the information which
voice commands are expected for the currently selected menu.
Help for voice control
When you give the voice command Start tutorial, the unit plays one of the sev-
en parts of the voice control tutorial. After saying the command again the next
part is played , etc.
Individual parts of the introduction can be called up separately by saying the
voice command Introduction part ... and the number 1 through 7.
Help for voice control
When you give the voice command Help, the unit displays voice commands for
the current selected menu. In some cases, after pronouncing Help again, the
next part of the help is shown.
Operation principle
Read and observe and on page 11 first.
The voice commands are only then to be spoken when the symbol is displayed
in the device screen or in the display of the combined instrument  .


The voice control system can usually be operated through the method “say
what you see” .
For example, the function button Dial number can be confirmed with the voice
command “Dial number”.
After switching on the voice control, the function buttons that can be con-
firmed with a voice command are highlighted in green.
During voice control operation, the following symbols appear in the device
screen.
Symbol Meaning
A message will be played
A voice command is awaited
Voice command entry was stopped
A voice command is recognized
It is not necessary to wait for the end of message playback when the device is
playing a message. The message can be ended by pressing the button  or
by pressing the icon key  on the multifunction steering wheel.
Conditions in the menu Navigation
The destination address can be entered by saying the city, the street and the
house number (if it is included in the navigation data) in one step.
You can say the house number and a further additional address in the form of
a number where necessary. The device then offers the number combination it
has found if the house number and the additional address, exists in the street
entered where appropriate.
If an address is entered in a country for which there is no support for voice
control, it is necessary to spell out the city and street names. The device indi-
cates this with a message.
not recognizing a voice command
Read and observe and on page 11 first.
If a voice command is not recognised, the device answers with Pardon? and
you can give a new command.
If the device does not recognise the second voice command, the help message
is provided again and you can give a new command. 

12 Device operation and settings

If the device does not recognise the third voice command, the system plays
the Cancel message and the dialogue is ended.
Correction of a voice command input
Read and observe and on page 11 first.
A voice command can be corrected, modified or re-entered by pressing the
button  or the icon key  on the multifunction steering wheel. However,
this is only possible if the symbol  is displayed on the screen.
You do not have to wait until the voice command is recognized by the device.
Stop/restore voice command input
Read and observe and on page 11 first.
Stop
In some menus, the process for voice command input can be stopped by turn-
ing the knob  .
This allows you more time for the voice command input.
When stopping, the symbol changes from  to ,
Restore
The procedure for voice command input can be restarted in one of the follow-
ing ways.
›By pressing the function key ,
›By pressing the button  on the device.
›By pressing the icon key  on the multifunction steering wheel.
Voice commands not included in the help
Read and observe and on page 11 first.
This chapter discusses some voice commands, which are not included in the
help topics.



All menus
Voice command Operation
Back  Return to the previous menu
Next page
Scroll through the menu / list / direc-
tory
Previous page
First page
Last page
Menu Radio
Voice command Operation
Next station  Nearest station in the selected fre-
quency range
Previous station  Previous station in the selected fre-
quency range
Start scanning Switch on the search for available sta-
tions
Switch on traffic reports Switching on/off the traffic pro-
gramme (TP)
Switch off traffic reports
Menu Media
Voice command Operation
Playback  - Play back
Pause  - Pause:
Previous track  Play the previous title
Next track  Playback the next title
Repeat all
 Switch on/off the repeat track
playback from the current album or
folder
Repeat track  - Switch on the repeated title play-
back
Stop repeat Switch off Album / Folder / Track re-
peat
Mix  Switch on the random track play-
back for the current album / folder
Stop mix  Switch off the random track play-
back for the current album / folder 
13
Device operation and settings

Menu Navigation - Navigation parameters
Voice command Operation
Turn on navigation announcements Switch navigation announcements
on/off
Turn off navigation announcements
Turn on dynamic route
Turn on dynamic navigation Switch navigation guidance assisted
by TMC traffic messages on or off
Turn off dynamic route
Turn off dynamic navigation
Show road signs on map Switch the traffic sign display in the
screen on/off
Turn off road signs on map
Show favourites Show or hide favourites icons in the
map
Turn off favourites
Menu Navigation - Route Information
Voice command Operation
Distance to destination Information about the distance to the
destination
Time of arrival Information concerning time of arrival
at destination
Driving time Information about the travel time to
the destination
Menu Navigation - Symbols in the menu with the settings of the map display
Voice command Operation
“2 D” mapa)  - Two-dimensional map display
“3 D” mapa)  - Three-dimensional map display
Destination map  - View a map with the destination
Overview map  - View a map with the route
a) The part of the voice command in parentheses must be spelled out to enter it.
Menu Navigation - Symbols for operator control of map scale
Voice command Operation
Orientation zoom  - Quick Map view
Centre map  - Centre the map on the vehicle po-
sition
Voice command Operation
Autozoom  Switch automatic scaling on/off
e.g. Scale five kilometres  - Enter the map scale manually
Device Settings
Introduction
This chapter contains information on the following subjects:
Sound settings 14
Screen settings 15
Time and date settings 15
Setting the device language 15
Setting the keyboard layout 15
Additional keypad language settings 15
Unit settings 16
Mobile device data transfer settings 16
Voice control settings 16
Safe removal of the data source 16
Restore factory settings 16
Bluetooth® settings 16
System Information 16
This chapter covers the device settings.
Sound settings
The scope of the following menu is dependent on the vehicle equipment
CANTON Sound system.
›Press the key  (Bolero).
or
›Press the key  →  .
■Volume - Volume settings
■Traffic reports - Adjustment of traffic announcements volume (TP)
■Navigation announcements - sets the volume for the navigation an-
nouncements
■Voice control - volume setting for voice output 
14 Device operation and settings

■Maximum switch-on volume - Sets the maximum volume after switching
on the device
■Volume adjustment - Speed-dependent volume increase
■AUX volume - Sets the volume for the device connected through AUX
■Bluetooth audio - Volume settings of the Bluetooth ® Audio profile connec-
ted device
■Lowering the entertainment - Lowers the audio volume (e.g. radio volume)
with activated parking aid
■Off - Mute is not active
■Scale 1 - 5 - Setting the Mute (1 = lowest, 5 = highest)
■MUTE - Mute switch
■Bass- Mid - Treble - Setting the equalizer
■Balance - Fader - Set the balance between left and right, front and rear
■CANTON Optimisation - Setting the room balance of the sound (all, front,
driver)
■CANTON Surround - Setting the surround sound levels in the area (“-9 ”Ster-
eo / “+9 ”full surround)
■CANTON Equaliser - Setting the equalizer
■Individual - Adjustment of treble, mid and bass
■Profile - Setting of the profile (e.g. Rock. Classical and so on).
■Subwoofer - Subwoofer volume settings
■Confirmation tone - Switch on/off confirmation tone when touching the
screen
■No navigation sound during call - Switches on or off the navigation prompts
during a telephone conversation
Screen settings
›Press the key  →  → Screen.
■Switch off screen (in 10 seconds) - Enable / disable the automatic power off
function
■Brightness: - Adjusts the brightness of the screen
■Confirmation tone - Switch on/off confirmation tone when touching the
screen
■Animation when finger near screen - Switch on/off the proximity sensors
(suppression of some function keys)
■Show clock in standby mode - Time and date displayed on the screen when
the ignition is switched on and the unit is switched off
Time and date settings
›Press the key  →  → Time and date.
■Clock time source: - Time Settings Source: Manual/GPS (Amundsen)
■Time: - Time settings
■Summer (DST) - Switches the summer time setting on/off (Amundsen)
■Time zone: - Select the time zone
■Time format: - Set the time format
■Date: - Date settings
■Date format: - Set the date format
Setting the device language
›Press the key  →  → Language/ Language .
The following language menu is displayed: In some languages, the device noti-
fications will be displayed after confirming a function button for the choice of
female or male device voice.
For some languages, pressing the function button Female or Male selects the
voice type for acoustic messages of the device.
The messages are generated by the device. The flawless clarity (e.g. road or
city name) cannot always be guaranteed.
Note
When a language is selected which does not support voice control, the device
will indicate with a message on the screen .
Setting the keyboard layout
›Press the key  →  → Keypad:.
■ABC - Keyboard character assignment in alphabetical order
■QWERTY - Keyboard character assignment QWERTY system
Additional keypad language settings
›Press the key  →  → More keypad languages.
In this menu, a keyboard language set can be added to allow the entering of
characters other than those in the currently selected language (function but-
ton ).
15
Device operation and settings

Unit settings
›Press the key  →  → Units.
■Distance: - Distance units
■Speed: - Speed units
■Temperature: - Temperature units
■Volume: - Volume units
■Consumption: - Consumption units
■Pressure: - Pressure units for tyre pressure
Mobile device data transfer settings
›Press the key  →  → Mobile device data transfer.
■Activate data transfer for apps- Turning the data transfer on and off
The activated function enables transmission of vehicle data for applications in
connected devices (e.g. MirrorLink ™ Applications).
Voice control settings
›Press the key  →  → Voice control.
■Dialogue style: - Setting the message style (long / short)
■Display available commands - Switch on/off the menus containing basic
voice commands when voice control is activated
■Voice control session start tone - Switch on/off the audible signal when
turning on the voice control
■Voice control session end tone - Switch on/off the audible signal when voice
control ends
■Input tone in voice dialogue - Switch on/off the audible signal for the voice
input
Safe removal of the data source
›Press the key  →  → Remove safely.
■SD card - Safe removal of the SD storage card
■SD card 1 - Safe removal of the SD storage card 1 (Amundsen)
■SD card 2 - Safe removal of the SD storage card 2 (Amundsen)
■USB 1 - Safe removal of the USB source in the front centre console
■USB 2 - Safe removal of the USB source in the back centre console
Restore factory settings
›Press the key  →  → Factory settings.
In this menu, some or all settings can be restored.
Bluetooth® settings
›Press the key  →  → Bluetooth.
■Bluetooth - Switch on/off Bluetooth® function
■Visibility: - Switch on/off the visibility of the Bluetooth® device for other de-
vices
■Name: - Change the device name
■Paired devices - Display the list of coupled Bluetooth ® Devices
■Find devices - Searches for available devices
■Bluetooth Audio (A2DP / AVRCP) - Turn on/off the ability to connect an au-
dio device (e.g. MP3 player, tablet etc...)
System Information
›Press the key  →  → System Information .
■Device part number: ... - Part number of the unit
■Hardware: ... - Version of the hardware used
■Software: ... - Version of the software used
■Navigation database: ... - Version of the navigation data
■Media Codec: ... - Media codec version
■Update software - Software Update (e.g. codecs)
The information about available software updates can be found on the ŠKODA
Internet pages www.infotainment.skoda-auto.com.
16 Device operation and settings

Radio
Operation
Introduction
This chapter contains information on the following subjects:
Main menu 17
Select broadcasting sector 17
List of available stations 18
Search and select available stations 18
Store preferred station 19
Station logos 19
TP Traffic programme 19
Radio DAB text and image presentation 20
The device allows analogue radio reception of FM and AM frequency ranges as
well as DAB digital radio reception.
CAUTION
■For vehicles with window antennas do not stick foil or metal coated stickers
to the window as this can lead to interference.
■Car parks, tunnels, tall buildings or mountains can interfere with the radio
signal even causing it to fail completely.
Main menu
Fig. 5
DAB main menu display
Read and observe on page 17 first.
Call up the main menu
›Press the  button.

Main Menu - Information and function keys » Fig. 5
The selected radio station (description or frequency)
Radio Text (AM, FM) / Description of the group (DAB)
Preset station buttons for favourite channels
Choice of radio range (FM / AM / DAB)
Choice of storage group for the preferred station
Changing the station
List of available stations
Manual / semi-automatic station search
Radio text display and images presentation (DAB)
Menu Settings Radio
Information symbol in the status line
Symbol Meaning
 Traffic information station
  Traffic information signals are not available or the selected sta-
tion is not a traffic information station
  RDS function is switched off (FM)
  AF Alternative frequency is switched off (FM)
Signal is not available (DAB)
If the displayed station name continuously changes (dynamic text), then it is
possible to fix the current text by holding your finger on the device screen in
the station name area. By holding your finger in the area of the station name
again, the station name is displayed in its entirety again.
Select broadcasting sector
Read and observe on page 17 first.
›Press the button  repeatedly.
or
›Press the function button D » Fig. 5 on page 17 , and select the desired
range.
A
B
C
D
E
 





17
Radio