Skoda RADIO NAVIGATION SYSTEM NEXUS - FOR OCTAVIA User manual

ŠkodaOctavia
SIMPLY CLEVER
www.skoda-auto.com Radionavigační systém Nexus
Octavia anglicky 12.05
S00.5610.28.20
1Z0 012 151 C
RADIO NAVIGATION SYSTEM NEXUS
A5-Nexus obal.indd 1A5-Nexus obal.indd 1 29.11.2005 9:32:1529.11.2005 9:32:15

About this Owner´s Manual
This Owner´s Manual contains important information, tips, suggestions
and warnings on using the radio navigation system. The other Owner´s
Manual in the vehicle wallet contain further information which you should
be aware of for your own safety and for the safety of your passengers.
Ensure that the complete vehicle wallet is always in the vehicle. This is
especially important when you lend or sell the vehicle to others.
This manual describes the scope of vehicle equipment at the time of
publication. Some of the equipment described here will not be available
until a later date, or is available only in certain markets.
Illustrations may vary from your vehicle in details. For this reason you
should regard illustrations as a general guide.
Directions and positions (e.g. right, left, front, rear) are always relative
to the direction of travel of the vehicle unless otherwise stated.
Some sections of this booklet do not apply to all vehicles. If this is the
case, a text at the start of the section indicates to which vehicles it
applies, e. g. “Applies to vehicles with CD changer”.
®Registered trademarks are marked ®. However, the absence of this
symbol does not constitute a waiver of the rights concerning any term.
The section is continued on the next page.
Indicates the end of a section.
WARNING
Texts with this symbol contain information on safety. They help
protect you from accidents and injury.
Caution
Texts with this symbol draw your attention to potential sources of damage
to your vehicle.
For the sake of the environment
Texts with this symbol contain additional information on the protection of
the environment.
Note
Texts with this symbol contain additional information.
s3f0
.
6
.
book
Page
ii
Thursday
,
November
3
,
2005
10:31
AM

Contents 1
Contents
Quick Reference Guide . . . . . . . .
Control elements . . . . . . . . . . . . . . . . . . . . . . .
Display elements on the screen . . . . . . . . .
Switching on and off . . . . . . . . . . . . . . . . . . . .
Radio/CD/Sound . . . . . . . . . . . . . . . .
Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sound, sound focus and volume . . . . . . . . .
Navigation . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination entry . . . . . . . . . . . . . . . . . . . . . . .
Destination memory . . . . . . . . . . . . . . . . . . . .
Parameters for route calculation . . . . . . . . .
Map and symbol displays . . . . . . . . . . . . . . .
Route guidance . . . . . . . . . . . . . . . . . . . . . . . .
Information and system
settings . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System settings . . . . . . . . . . . . . . . . . . . . . . . .
External units . . . . . . . . . . . . . . . . . . . .
Calling up external units . . . . . . . . . . . . . . . .
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
4
4
6
6
10
12
14
14
17
23
27
32
38
41
41
42
44
44
45
s3f0
.
6
.
book
Page
1
Thursday
,
November
3
,
2005
10:31
AM

Quick Reference Guide2
Quick Reference Guide
Control elements
This overview will help you to quickly familiarise yourself with the control elements.
On/off knob (push) and volume control (turn). The volume
control will regulate the volume of the audio source currently
Fig. 1 Overview of the control elements
A
1
s3f0
.
6
.
book
Page
2
Thursday
,
November
3
,
2005
10:31
AM

Quick Reference Guide 3
selected. A column will indicate the volume level. The
volume of a telephone conversation can also be regulated
using the volume control.
Entries in the screen menus can be made using the menu
button. Turn to mark a function or a sub-menu. Press to
select a function or a sub-menu.
Sound and sound centre settings . . . . . . . . . . . . . . . . . .
Left and right of the screen - 5 function/station keys.
−The term function key is used because the keys have
different functions depending on the menu being shown in
the display. If the text says, for example, “Press
”, then press the function key next to where
the text “Dest. on map” appears on the screen.
−Station keys: The upper 6 function keys are used as
station buttons in the radio mode. Stations can be stored
on these keys. The upper 6 function keys can be used to
select the inserted CDs in CD changer mode.
Backwards/forwards keys, apply to the active audio
source
−press briefly: radio mode: station change in the memory;
CD mode: changes track
−press longer: radio mode: station change in the station
listing; CD mode: fast forward/backward search
Switches between day and night display or darkens the
screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slot for an audio or navigation CD. . . . . . . . . . . . . . . . . . . .
CD eject button. The ejected CD will be pulled back into
the unit if it is not fully withdrawn within 10 seconds.
Set flagged destination. The unit will store the current
vehicle position when this button is pressed. When this
button is pressed again, the flagged destination will be over-
written if it has not been stored in the destination memory. .
The traffic jam button calls up the input menu to exclude
route sections in a route list or to enter traffic jam information
manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back to previous menu.
Map display when Navigation CD is inserted / Switch
to symbol display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calls up the Navigation main menu. . . . . . . . . . . . .
Switches to other auxiliary audio or video units. . . . .
reserved for additional functions at a later date
CD and CD changer control 1) . . . . . . . . . . . . . . . . . .
Radio menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call up system settings, traffic reports, position
displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARNING
Adjust the volume so that you can still hear signals coming from
outside the vehicle, such as fire brigade, ambulances or police
cars.
Caution
The screen is not a touch screen. Do not press on the surface. The screen
can be cleaned with a soft cloth (and alcohol, if necessary). Do not use
solvents such as turpentine or petrol to clean the surface as they will
corrode the material.
A
2
A
312
A
4
Dest. on map
A
5 
A
6
42
A
710
A
8
A
9
17, 23
1) You will find a description in the corresponding Owner´s Manual.
A
10
30
A
11 ESC
A
12 MAP
39
A
13 NAVI 16
A
14 AUX 44
A
15 TELE
A
16 CD 10
A
17 RADIO 6
A
18 INFO
41
s3f0
.
6
.
book
Page
3
Thursday
,
November
3
,
2005
10:31
AM

Quick Reference Guide4
Display elements on the screen
This section describes the elements seen in the display.
The functions or sub-menus shown on the screen can be called up by
pressing the function key situated directly next to them. This can also
be carried out by first turning the menu knob and then pressing it.
The orange selection box can be moved using the menu knob. It will
disappear from the screen if the unit is not used for 30 seconds and
will appear again if the menu knob is turned.
The selection of the function characteristics, such as destin. or
overview, can only be reached by pressing and turning the menu
knob.
The right part of the status bar contains additional information or the
option “back with ESC”
Details of the active audio source or navigation status are shown in
the centre part of the status bar.
The left part of the status bar shows the current menu.
Below the status bar
An orange marking indicates which source is active. Press the key
beneath it to call up the main menu for this source.
A green marking indicates which source is still active in the background
(the radio in this example). Press the key beneath it to call up the main
menu for this source.
If the text CD ? is displayed in the marking above the button, the CD
inserted in the CD drive can not be read.
Switching on and off
A safety code made up of four characters must be entered
when switching on for the first time.
Switching on/off
– Press the rotary/push knob ⇒page 2, fig. 1 .
Fig. 2 Display
elements
A
A
A
B
A
C
A
D
A
E
A
F
CD
Fig. 3 Entering the
safety code
A
1
s3f0
.
6
.
book
Page
4
Thursday
,
November
3
,
2005
10:31
AM

Quick Reference Guide 5
– Press the rotary/push knob again to switch the unit off.
Entering the safety code
– The safety code can be found on the unit card.
– Enter the characters by turning and pressing the menu knob
⇒page 4, fig. 3.
– Press if you wish to change incorrect entries.
– Once the safety code as entered corresponds to the code
given on the unit card, press .
The last menu used and also the last audio source used before switching
off will be selected automatically when the unit is switched on again. The
radio navigation system will be switched off if the ignition is turned off. The
unit can be switched on again using the rotary/push knob when the igni-
tion is switched off. It will be switched off automatically after an hour to
stop the vehicle battery from running down.
The following text might appear if there is no CD in the CD slot and the
safety code has been entered and you have pressed : No CD is
inserted. Please insert a ŠkodaAuto Navigation RNS CD.
If you do not wish to use the navigation system immediately, you can still
select a different audio source by pressing the appropriate button.
Comfort Coding
If you have not received a security code for your radio, it means that your
car is fitted with comfort coding system, which does not require a code. In
case of disconnection and reconnection of car battery, first switch on the
power by the starting key, then switch on the radio. If you need a code,
contact your Škoda service.
Note
The unit will be blocked for one hour if an incorrect code is entered three
times. The code can be entered again after this one hour has elapsed.

OK
OK
s3f0
.
6
.
book
Page
5
Thursday
,
November
3
,
2005
10:31
AM

Radio/CD/Sound6
Radio/CD/Sound
Radio
Overview
Information is given here on how to select and store
stations.
The following radio functions are selected via the function keys:
•– Scans stations or stores those stations with the strongest
reception ⇒page 6, “Scan/AS”,
•– Calls up station list or manual frequency input ⇒page 8,
“Station selection from a list (FM only)”,
•– Sets the waveband and traffic radio, mute function ⇒page 7,
“Setting waveband/Muting”,
•– Set-up for RDS functions ⇒page 9 Settings.
Scan/AS
The stations with the strongest reception are either
scanned or stored automatically.
Playing stations briefly
– Briefly press ⇒fig. 5.
Autostore on the second memory level (FM2 or AM2)
– Press for longer than 2 seconds to allocate those
stations with the strongest reception in the selected waveband
(FM2 or AM2) to the upper 6 function keys.
Fig. 4 Radio main
menu
Scan / _AS
List / _MAN
Band
Set-up
Fig. 5 Autostore AS
Scan / _AS
Scan / _AS
s3f0
.
6
.
book
Page
6
Thursday
,
November
3
,
2005
10:31
AM

Radio/CD/Sound 7
Autostore for all memory levels (Initial Autostore)
– Press for longer than 10 seconds to allocate those
stations with the strongest reception in all wavebands to the
upper 6 function keys.
The selected function will be shown on the screen and can be stopped by
pressing again.
A scan in the FM waveband will play through the list of registered stations.
A scan in AM will play all stations with a high quality reception. Each
station scan lasts 8 seconds. Press the menu knob or if you
would like to stop at the station currently being played.
Note
Use the function “Initial Autostore” if you are using the unit for the first time
or when selecting new stations in the waveband. Any station names on the
station keys will be overwritten. The process of searching for and storing
the station names takes a few seconds.
Setting waveband/Muting
– Press in the radio main menu ⇒page 6, fig. 4 to see
the frequencies.
– Press or to receive VHF stations.
– Press or to receive medium wave stations.
– When in FM1 or FM2 mode, press to receive traffic infor-
mation reports.
– Press / to mute the radio or to switch the
mute function off/on.
The last heard station will be played for the waveband selected. Traffic
information reports will be relayed even when the radio has been muted.
The TP function must be active for this purpose (white column next to the
field). When TP is active, the letters TP are lit up in orange. The increased
Scan / _AS
Scan / _AS
Scan / _AS
Fig. 6 Radio waveband
Band
FM1 FM2
AM1 AM2
TP
Radio off Radio on
s3f0
.
6
.
book
Page
7
Thursday
,
November
3
,
2005
10:31
AM

Radio/CD/Sound8
volume level for the traffic announcement can be lowered by pressing the
button .
Station selection from a list (FM only)
The radio navigation system will automatically compile
and store a list of receivable FM stations after the unit is
switched on.
– Press in the radio main menu ⇒page 6, fig. 4 to
see the stored stations.
– Select a station by turning and pushing the menu knob or by
using the right-hand function keys.
– Select a station from the list by turning and pushing the menu
knob. You can scroll through several pages of the list using the
scroll markers , , and and confirm your selection
by pressing .
– You can also select the stations stored in the list by pressing
the button or for more than 2 seconds.
Station selection from memory or by entering
frequency
Station selection from memory
– Briefly press button or to listen to the stored station.
Station selection by entering frequency
– Press the button ⇒page 2, fig. 1 and hold it
pressed for more than 2 seconds. As soon as the information
regarding the frequency appears with an orange frame and
the word manual in the middle of the display, you can manu-
ally enter the frequency. The station finding starts in the
selected direction in steps of 0.1 MHz (FM) or 9 kHz (AM). You
can set in this way one of your known station frequencies. You
can also change the frequency by turning the menu knob.
– For fine tuning press the button or .
INFO
Fig. 7 List of stations
List / _MAN
   
OK
 
 
List / _MAN
A
5
 
s3f0
.
6
.
book
Page
8
Thursday
,
November
3
,
2005
10:31
AM

Radio/CD/Sound 9
Allocating the stations to the station buttons
Stations can be allocated to the buttons to make it easier
to select them quickly.
– Press one of the upper 6 station buttons until you hear a signal
⇒page 2, fig. 1 . The station you are listening to is now
stored on the button.
A total of six stations can be stored on the station buttons for each mode;
FM1, FM2 or AM1 or AM2. The short form of the station name or the
station frequency will appear next to the button. Press one of the buttons
if you wish to listen to one of the stored stations.
Note
The memory on a button will be overwritten if a new station is stored
there.
RDS settings
Some stations transmit text and information in addition to
the station name.
– Press in the Radio main menu ⇒page 6, fig. 4.
Further text information as running text will not be displayed on the
screen, in addition to the station name, for all RDS stations.
A tick will indicate which options have been selected.
Function keys
•fixed: Only the station name will be shown.
•variable: Text information is shown as running text.
– autom.: The selected regional programme of a station
broadcasting over a wide area will continue to be displayed even when
A
4
Fig. 8 RDS functions
Set-up
RDS Name
RDS Regional
s3f0
.
6
.
book
Page
9
Thursday
,
November
3
,
2005
10:31
AM

Radio/CD/Sound10
you enter the broadcasting area of another regional programme of the
same station.
⇒page 42
WARNING
Your attention must, however, always be concentrated on road
traffic as an absolute priority. Do not allow yourself to be distracted
by the RDS running text.
CD
Listening to an audio CD
Listening to a CD
– Press the button ⇒page 2, fig. 1. If a CD is already in the
player, the last played track will be selected. Otherwise the
following will appear briefly on the screen: “No Audio CD”.
– Insert a standard 12 cm audio CD. The play function will start
automatically.
Playing the previous or next track
– Press button or briefly.
Fast forward/reverse
– Press and hold button or .
Ejecting a CD
–Press ⇒page 2, fig. 1 .
The number of the track and its length are shown on the screen. TP lights
up in orange if traffic reports are to be received and TMC indicates
whether TMC stations are being received ⇒fig. 9.
Function keys during the play function:
... – Selects the corresponding CD in the CD changer if
connected 2).
– Selects the CD that is in the unit.
– All tracks on the CD will be played for 8 seconds at a time.
– The tracks on the CD will be played in a random order.
⇒page 42
Syst. settings
Fig. 9 Main menu CD
2) You will find a description in the corresponding Owner´s Manual.
CD
 
 

A
8
CD1 CD6
Int. CD
Scan
Mix
Syst. settings
s3f0
.
6
.
book
Page
10
Thursday
,
November
3
,
2005
10:31
AM

Radio/CD/Sound 11
WARNING
The CD player is a class 1 laser product. If it is opened, or is faulty
or damaged, there is a risk of invisible laser beams escaping from
the unit. The CD player contains no parts that have to be serviced.
Any repair work that needs to be done should, therefore, be carried
out by Škoda Service exclusively.
Caution
•Only 12 cm standard CDs should be used, not 8 cm single CDs. Only
round CDs should be inserted in the CD slot. “Special shape CDs” can not
be played and they will damage the CD player.
•Slide the CD with the printed side up into the CD slot up to the point
where it is drawn in automatically. Hold the CD at the sides. Avoid leaving
fingerprints on the CD. Clean the CD with a dry, lint-free cloth. When doing
this, wipe the CD from the centre outwards. Do not clean the CDs using
alcohol or solvents. Do not place the CDs near heat sources or in the
direct sunlight. Do not write on the CDs and do not attach stickers to them.
Note
•The upper 6 function keys are only active if a CD changer has been
connected.
•CD-R and CD-RW formats can also be played, depending on the
quality of the blanks.
•If the text CD ? is displayed in the small marking above the button,
the CD inserted in the CD drive can not be read.
Applies to vehicles: with CD changer
Playing a CD from the CD changer
How to use the radio navigation system to select a CD in
the CD changer.
– Use the function keys to to select a CD from the
changer.
Uneven road surfaces and strong vibrations may cause the CD to jump.
The CD play function should be switched off in this case.
CD
Fig. 10 CDs currently
in the changer
CD1 CD6
s3f0
.
6
.
book
Page
11
Thursday
,
November
3
,
2005
10:31
AM

Radio/CD/Sound12
Sound, sound focus and volume
This section describes how the sound character and the
volume of different sound sources can be set individually.
– Press the button ⇒page 2, fig. 1 to open the Sound
main menu.
Function keys in Sound main menu:
or – Treble or Bass settings ⇒fig. 11
3) – Volume setting for the mid-range frequencies
– Sound focus setting left/right
– Sound focus setting front/rear
– Opens the volume set-up where individual volume settings can
be made for the different audio sources ⇒fig. 12.
Function keys in the volumes set-up function:
– The setting for the sensitivity of the speed-dependent volume
adjustment (GALA). The volume of the audio source will be increased
automatically by GALA as the road noise increases at higher speeds. The
volume will be increased more the further the control is set towards the
right.
– Minimum volume for traffic announcements
– Minimum volume for telephone conversations
– Minimum volume for navigation system announcements
– The traffic announcements are muted as long as a orange
bar can be seen next to the function key.
– Sets the minimum volume for when the unit is switched on.
Note
By pressing buttons ⇒page 2, fig. 1 , and status button
at the same time, you can reset the radio navigation system to the
Fig. 11 Sound main
menu
Fig. 12 Volume
settings
3) Vehicles with a sound system

A
3
Treble Bass
Mid
Balance
Fader
Volume
GALA
TA Min
Telephone
NAV Min
NAV mute
Initial volume

A
3TELE
A
15
A
10
s3f0
.
6
.
book
Page
12
Thursday
,
November
3
,
2005
10:31
AM

Radio/CD/Sound 13
factory settings. The message, Default settings being made. Please
wait! is shown.
s3f0
.
6
.
book
Page
13
Thursday
,
November
3
,
2005
10:31
AM

Navigation14
Navigation
Overview
How does the navigation system work, and how is it
operated?
An optimal route is defined using sensors, satellites and
traffic reports and the driver is then guided to his or her
destination.
The current vehicle position is determined using a system of satellites
(GPS - Global Positioning System). Sensors in the vehicle measure
distances that have been driven. Measured values are compared using
the detailed map material on the navigation CD and corrected with the
assistance of TMC traffic announcements as necessary. An optimal route
to the destination is determined in this way.
Navigation announcements and direction arrows shown on the screen
and in the combi-instrument guide you safely and conveniently to your
destination. You can drive to a given address in towns you are unfamiliar
with, or drive to the nearest garage or be guided to a hotel.
In this chapter, answers can be found to the following questions:
•What rules do I have to keep to when using the navigation system?
⇒page 14, “Safety”
•How do I use the navigation CD? ⇒page 15, “The navigation CD”
•Can I listen to music when using the navigation system? ⇒page 15,
“General notes”
•What happens if I leave the recommended route? ⇒page 15,
“General notes”
•Can a navigation announcement be repeated? ⇒page 39,
“Announcement of navigation recommendations”
•How does the radio navigation system respond when driving in an
underground car park or a tunnel? ⇒page 15, “General notes”
•How do I enter destinations? ⇒page 17, “Destination entry”
•How can I enter garages, restaurants or hotels as destinations?
⇒page 21, “Special destinations close to the address”
•Can I store destinations in a memory? ⇒page 23, “Destination
memory”
•What parameters can I set for route calculation? ⇒page 27, “Param-
eters for route calculation”
•What can I see on the screen? ⇒page 32, “Map and symbol displays”
•Can I stop the route guidance function before I reach my destination?
⇒page 38, “Route guidance”
Safety
The navigation system determines the position of the vehicle, the direction
and distance and the route to a selected destination without taking traffic
regulations into account. Navigation recommendations are given as
announcements by the system. Direction arrows are also shown on the
screen. The destination is entered when the vehicle is stationary. The
route guidance function is designed for cars and is thus unsuitable for
larger commercial vehicles.
s3f0
.
6
.
book
Page
14
Thursday
,
November
3
,
2005
10:31
AM

Navigation 15
WARNING
•Please observe the laws of road traffic legislation when
following the recommendations made by your navigation system.
•Route guidance is subject to constant changes despite the
information about one-way streets, pedestrian zones etc. stored on
the navigation CD. Information on traffic lights, stop and right of
way signs, parking and stopping restrictions as well as lane
constrictions is not included in the navigation system. Traffic signs
and legislation always have priority over the recommendations
made by the system.
•Adjust your speed to suit road traffic conditions and also
weather and visibility conditions. Do not drive faster in fog, for
example, if the navigation system tells you to do so.
The navigation CD
Inserting the navigation CD
– Press the button ⇒page 2, fig. 1 to eject any CD in the
CD slot.
– Remove the CD and insert the navigation CD with the written
side facing up.
– Push the CD into the slot until the radio navigation system
pulls it in. The program stored on the navigation CD is loaded.
Do not remove the navigation CD before the loading process
is finished.
The navigation CD contains a digitalised road map. The extent to which
small villages, streets and house numbers are contained on the CD
depends on the CD version.
The content of the CD is constantly being updated. You will receive infor-
mation on new updates at your next Škoda Service. You will need a new
navigation CD for every country that you travel to.
Note
If the text CD ? is displayed in the small marking above the button,
the CD inserted in the CD drive can not be read.
General notes
You can continue to listen to the radio or CD (via the CD changer) whilst
you are being guided to your destination.
When entering an address (town, street), only those letters or symbols
which make up a logical entry will be presented. A list of possible names
will be shown. Do not forget to enter the blank space in names made up
of more than one word, such as High Wycombe.
The route will be recalculated if you leave or disregard the route that was
originally calculated. This process takes only a few seconds.
The last announcement made can be repeated. The volume of a naviga-
tion recommendation can be changed whilst it is being made.
A variety of different information on the route can be called up during
active route guidance. The scroll function can be used to page through
lists shown on the screen, either line by line or page by page.
If the display Off Road appears on the screen, it means you are located
on a non-digitalised street, e.g. on a farm track. The GPS satellites will not
be able to reach your antenna when you are in a tunnel or underground

A
8
CD
s3f0
.
6
.
book
Page
15
Thursday
,
November
3
,
2005
10:31
AM

Navigation16
garage, meaning that the unit orientates itself via the wheel sensors. If you
try to carry out a route calculation in this situation you may hear the
announcement: “You are located on a non-digitalised street”. Drive on until
the display Off Road disappears.
Main menu - Navigation
– Press the key to enter the Navigation main menu
⇒page 2, fig. 1 .
Function keys in the Navigation main menu
– Starts route guidance to the entered destination. Pressing
this button again will stop the route guidance function ⇒page 38, “Route
guidance”.
– Field for entering your destination ⇒page 17, “Destination
entry”
– Field for entering a stopover destination. A stopover destina-
tion is entered in the same way as a destination. A stopover destination is
deleted from the screen as soon as it has been reached. It will, however,
remain in the memory Last dest. ⇒page 17, “Destination entry”. If the
stopover destination is reached, you will be informed that you have
reached your destination, and route guidance to the final destination is
started automatically. If the stopover destination is not reached exactly,
e.g. because it is not located directly on a road, you will be informed that
you have reached the destination area. Route guidance to the next desti-
nation is not started automatically.
– Defines the parameters for route calculation ⇒page 27,
“Parameters for route calculation”.
– Enter your location manually or start a demonstration
⇒page 28, “Settings”.
Fig. 13 Main menu
Navigation
NAVI
A
13
Start route gd.
Destination
Stopover
Route opt.
Set-up
s3f0
.
6
.
book
Page
16
Thursday
,
November
3
,
2005
10:31
AM

Navigation 17
Destination entry
Starting destination entry
Two addresses can be entered for the route calculation;
the address of the destination and the address of the stop-
over destination.
– Press the key to enter the Navigation main menu
⇒page 2, fig. 1.
– Press or in the Navigation main menu
⇒page 16, fig. 13 to select between the destination entry
options.
You will see a message that states that a destination has not yet been
defined if the destination is being entered for the first time. The last used
destination will be displayed if a destination has already been entered.
There are various methods of entering a destination or a stopover desti-
nation. The procedure for entering the stopover destination is the same as
for the destination.
– Enter the destination using town and street names
⇒page 18, “Entering a new address (town, street, house number)”.
or – Select a destination from a list of destina-
tions that have already been stored ⇒page 19, “Last destinations”.
Fig. 14 Destination
Fig. 15 Stopover desti-
nation
NAVI
A
13
Destination Stopover
New Address
Last dest. From dst. mem.
s3f0
.
6
.
book
Page
17
Thursday
,
November
3
,
2005
10:31
AM

Navigation18
– Enter a restaurant, a garage, an airport, border crossing
etc. as a destination ⇒page 21, “Special destinations close to the
address”.
– The position were you were located when you last
pressed button ⇒page 2, fig. 1 is entered as the destination.
– Mark your destination on a map using a crosshair
⇒page 21, “Destination on the map”.
– Enter the longitude and latitude of a destination
⇒page 22, “Position destination”.
– Select a destination from the travel guide. A travel guide
is only available on certain navigation CDs. Further search functions
depend on the content of the travel guide.
– Store, delete or edit destinations in the destination memory
⇒page 23, “Destination memory”.
– Deletes the entered stopover destination.
Entering a new address (town, street, house number)
– Press , or to enter the name
using the letter selection function.
Special dests.
To flagged dst.

A
9
Dest. on map
Position dest.
Additional De...
Edit memory
Del. stopover
Fig. 16 Entering a new
address
Fig. 17 Entering a
town name
Town Street House number
s3f0
.
6
.
book
Page
18
Thursday
,
November
3
,
2005
10:31
AM