SKY-HERO Anakin Installation guide

Assembly
Instrucon Manual
2015.08
All manuals and user guides at all-guides.com
all-guides.com

TABLES OF CONTENT
GLUE THE TUBES END’S 1
ATTACH YOUR MOTORS 2
ATTACH MOTOR MOUNTS ON ARMS 3
ROUTE YOUR MOTOR CABLES 4
FIX YOUR SIDE FRAME USING 2 SCREWS 4
SOLDER YOUR ESC’S 4
USE SCHRINK TUBE TO PROTECT YOUR ESC’S 4
SLIDE ESC’S INTO THE TUBES 4
PRESS THE INSERT IN POSITION 4
CHOOSE THE POSITION OF YOUR ARMS 9
SLIDE YOUR MOTOR SHAFTS INTO THE MOUNTING JIG 10
SCREW YOUR LOWER FRAME 11
FIX YOUR MOTOR MOUNT 12
ATTACH YOUR Z SPACERS 13
FIX YOUR CAMERA PLATE IN POSITION 14
CAMERA ANGLE 15
ADJUST MOTORS ANGLE 16
ATTACH YOUR CANOPY 17
All manuals and user guides at all-guides.com

SCREW 1/1 SCALE
ISO 7380 M3X6MM
ISO 7380 M3X4MM
ISO 7380 M3X6TP MM
ISO 7380 M3X30MM
ISO 7380 M2.5X8MM
HEX NUT 2.5MM
All manuals and user guides at all-guides.com

SKH01-106-F
SKH01-106-R
SKH03-280 ( FRONT TUBE )
(ou SKH03-240)
SKH03-280 (REAR TUBE
(ou SKH03-240 )
USE EPOXY
GLUE
USE EPOXY
GLUE
8MM
8MM
GLUE THE TUBES END’S
Use 5min epoxy glue
(Whipe out excess of glue with acetone)
1
Please make sure you push the


*
*
*
USE EPOXY
GLUE
FIG. 1
All manuals and user guides at all-guides.com

SKH04-009
SKH01-105
ISO 7380 M3x6MM
ATTACH YOUR MOTORS
Warning! Before starng:
- Make sure to idenfy your clockwise (CW) and counter-clockwise (CCW) motors*.
- Be aware that all your wires will go backwards as shown in gure 3
2
FIG. 2
FIG. 3
CW
CW
CCW
CCW
* 
All manuals and user guides at all-guides.com

CW CCW
CCW CW
3
BUILD 1CW+1CCW
FOR FRONT SIDE
BUILD 1CW+1CCW
FOR REAR SIDE
 (See gure)
1CW+1CCW
 1CW+1CCW
FIG. 4
FIG. 5
ATTACH MOTOR MOUNTS ON ARMS

a «clic»
(it can require quite an important pressure)
All manuals and user guides at all-guides.com
all-guides.com

SKH03-280-A
OU ( SKH03-240-A )
( LEFT SIDE )
SKH01-170-00
(OPTION = SKH06-001)
ISO 7380
M3x8TP
ROUTE YOUR MOTOR CABLES
Rear cables = 220mm long / Front cables = 150mm long
FIX YOUR SIDE FRAME USING 2 SCREWS
Build le + right side
4
FIG. 6
FIG. 7
All manuals and user guides at all-guides.com

SKH04-014*


SOLDER YOUR ESC’S
And check your motors direcon

SKH04-014*
5
* 
USE SOLDER
& WELDING
FIG. 8
FIG. 9
All manuals and user guides at all-guides.com

SLIDE ESC’S INTO THE TUBES
6
FIG. 10
All manuals and user guides at all-guides.com

SKH03-200-S
SH54-03
(FROM SKH07-111)
SH54-01
(FROM SKH07-111)
SKH03-200-U
SH54-03
(FROM SKH07-111)
SKH03-200-U
PRESS THE INSERT IN POSITION
In order to mount the frame you must rst insert the PEM’s by ghtening them
one by one unl you reach themaximum posion.
Use the threaded insert on upper frame.
TIP:
Use 1 frame spacer + 1
M3x30MM screw, to press
your insert in posion
Once nished you will have this:
7
THREADED
NOT THREADED
SH54-03
FIG. 11
All manuals and user guides at all-guides.com

SLIDE YOUR FRAME SPACER AROUND THE TUBES
(Use the threaded insert on upper frame)
FRONT SPACER
REAR SPACER
SKH01-103-F SKH01-103-R
SKH01-103-F
SKH01-103-R


8
FIG. 13
FIG. 12
All manuals and user guides at all-guides.com
all-guides.com

CHOOSE THE POSITION OF YOUR ARMS
ACCORDING THE CENTER OF GRAVITY ADJUSTMENT YOU WANT
FRONT SPACER REAR SPACER
SKH01-103-F SKH01-103-R
FRONT UP
LOW CG
CROSSED SETUP
HIGH CG
Standard setup
REAR UP
REAR UP
REAR DOWN
FRONT DOWN
FRONT DOWN
9
FIG. 14
All manuals and user guides at all-guides.com

SLIDE YOUR MOTOR SHAFTS INTO THMOUNTING JIG
10
FIG. 15
All manuals and user guides at all-guides.com

ISO7380 M3x30MM



SOLDER YOUR ESC CABLES, EQUIPEMENTS CABLES, ( VTX, UBEC, LED, ETC... )
TO YOUR BATTERY CONNECTOR CABLES
SCREW YOUR LOWER FRAME
(DO NOT OVERTIGHT)
BATTERY CONNECTOR
CABLES
EQUIPEMENTS
11
FIG. 16
FIG. 17
All manuals and user guides at all-guides.com

DIN912 M2,5x8MM
HEX NUT
M2,5x0,5MM
FIX YOUR MOTOR MOUNT
12
FIG. 18
All manuals and user guides at all-guides.com

ISO7380 M3X30MM

SCREW THE THIRD SCREW
13
FIG. 19
All manuals and user guides at all-guides.com
all-guides.com


ISO7380 M3x6MM

ISO7380 M3x6 MM


ATTACH YOUR Z SPACERS


14
FIG. 20
FIG. 21
FIG. 22
All manuals and user guides at all-guides.com

CAMERA ANGLE
 angle of the camera
20 °
20 °
Standard setup
15
FIG. 23
FIG. 24
FIG. 25
* 
* Cam
* Cam
* Cam
All manuals and user guides at all-guides.com

ADJUST MOTORS ANGLE
banked posionplacc ring or alu ring

WARNING!oponal sideframes
website (www.sky-hero.com)
0°
10°
Standard setup
Banked setup
16
FIG. 26
FIG. 27
All manuals and user guides at all-guides.com




ATTACH YOUR CANOPY

17
FIG. 28
All manuals and user guides at all-guides.com