SKY-HERO Anakin Club Racer User manual

Anakin Club Racer ENGLISH

CONGRATULATIONS on your purchase of a SKY-HERO Anakin Club Racer, we hope that it will provide you
with many years of fun and entertainment.
SKY-HERO products are designed and developed in Belgium (Europe), but distributed and supported across
the globe through a network of dealers and outlets that can provide assistance and advice.
The SKY-HERO
and reasonable support service
INTRODUCTION
OUR PHILOSOPHY
OUR CONCEPTS
SAFETY ADVICE WARNING!

All SKY-HERO

SKY-HERO




FOLDABLE FRAMES FOR EASIER TRANSPORTATION PACKNGO
AERODYNAMIC DESIGN PROTECTING ELECTRONICS SLEEKNSEXY
HEAVY LIFT CAPABILITY WITH GREAT STABILITY LIFTNSTABLE
RACE BRED MODELS FOR COMPETITION EVENTS RACENWIN
CUSTOMISABLE AND UPGRADEABLE PLATFORMS EVOLVENGROW
LEAD THE COMPETITION THROUGH INNOVATION 1STEPAHEAD
2

 
 
 
 
aircraft, to ensure you are in compliance with them. In particular you should avoid any sensitive areas
such as Military establishments, Airports, Power stations and populated areas.
     
buildings, people and anything which is outside of your control.
 
a loss of radio contact with the aircraft puts it out of your control and could cause unpredictable
results.
 
 
unpredictable results.
 
it is in flight.
 
 
 
 
 
aircraft or its electronics and wiring.
 
the transmitter on (checking the position of all controls) before connecting the battery.
 
such as transmitter, battery chargers etc.
GENERAL INSTRUCTIONS
AND GUIDELINES FOR USE
3

TABLE OF CONTENTS
PARTS LISTING 5
ADDITIONAL ITEMS REQUIRED TO COMPLETE 7
REQUIRED TOOLS AND EQUIPMENT 7
MAIN FRAME - ASSEMBLING THE ARMS 8
ROUTING OF MOTOR CABLES 8
FIXING THE MOTORS TO THE FRAME 9
SOLDERING THE MOTORS TO THE ESCS 9
PDB CONNECTIONS 14
CAMERA SETUP 16
CHANGING YOUR VTX OUTPUT POWER 18

TRANSMITTER 19
CC3D FLIGHT CONTROLLER SETUP USING
OPEN PILOT GCS SOFTWARE 20
TRANSMITTER SETUP WIZARD 26
TESTING YOUR ANAKIN CLUB RACER ARMING
PROCESS WORKS 29
TROUBLE SHOOTING 29
   
ATTACH YOUR PROPELLERS 32
  
BEFORE YOU TAKE OFF 35
MOTOR ARMING AND TAKING OFF 35
USING ALTERNATIVE RADIOS & RECEIVERS 36
LIMITED WARRANTY 38


PARTS LISTING
ISO7380 M3X14MM 2X
ISO7380 M3X10MM 24X
ISO7380 M3X6MM 8X
SELF TAPPING SCREW M3X6MM 4X
DIN 9021WASHER M3 8X
 
FRONT MAIN SPACER 2X
  
Screwset
SKH07-112
Note: - screws 1/1 scale
5

SKH01-104-Z LED SUPPORT
MASSE:
A4
FEUILLE 1 SUR 1
ECHELLE:1:1
No. DE PLAN
TITRE:
REVISION
NE PAS CHANGER L'ECHELLE
MATERIAU:
DATE
SIGNATURE
NOM
CASSER LES
ANGLES VIFS
FINITION:
SAUF INDICATION CONTRAIRE:
LES COTES SONT EN MILLIMETRES
ETAT DE SURFACE:
TOLERANCES:
LINEAIRES:
ANGULAIRES:
QUAL.
FAB.
APPR.
VERIF.
AUTEUR
OR
OR
6
SKH03-215-F 5"
SKH03-260-F 6"
SKH03-215-R 5" 2X
SKH03-260-R 6" 2X
SKH03-201
SKH05-026
SKH03-201
SKH03-015
SKH03-015
  
  

SKH03-201
SKH05-024-01
MASSE:
A3
FEUILLE 1 SUR 1 ECHELLE:1:1
No. DE PLAN
TITRE:
REVISION
NE PAS CHANGER L'ECHELLE
MATERIAU:
DATE
SIGNATURE
NOM
CASSER LES
ANGLES VIFS
FINITION:
SAUF INDICATION CONTRAIRE:
LES COTES SONT EN MILLIMETRES
ETAT DE SURFACE:
TOLERANCES:
LINEAIRES:
ANGULAIRES:
QUAL.
FAB.
APPR.
VERIF.
AUTEUR

ADDITIONAL ITEMS REQUIRED TO COMPLETE


 
 

 

 
 
Esc’s
 

 
 
 
 

 


REQUIRED TOOLS AND EQUIPMENT
 
 
 
 
 
 



7

MAIN FRAME - ASSEMBLING THE ARMS
ROUTING OF MOTOR CABLES
A
B
DÉTAIL A
ECHELLE 2 : 1
DÉTAIL B
ECHELLE 2 : 1
M3X10mm
M3X14mm
MIDDLE FRAME SPACER
FRONT FRAME SPACER
8

M3X10mm
FIXING THE MOTORS TO THE FRAME
SOLDERING THE MOTORS TO THE ESCS
               


USE SOLDERING
IRON, TO CONNECT
CABLES TO ESC’S
         


           


ESC’s motor side.
9

PRO TIP



to turn CW












CW
CCW
CCW
CW
10









11

+
+
+




+
USE SOLDERING
IRON, TO CONNECT
CABLES TO POWER
DIST. BOARD


SUITABLE TO POWER YOUR VTX,








             













12

ALIGN EDGE OF THE PDB
WITH THE FRAME


13

PDB CONNECTIONS
+
+
+




+


SUITABLE TO POWER YOUR VTX,






NOTE:

 














15



NOTE




NOTE:

45°
45°

30°
CAMERA SETUP


16








SELF TAPPING SCREW M3X6mm
WASHER
PLASTIC SCREW M3X6mm
M3X6mm
17

CHANGING YOUR VTX OUTPUT POWER
FROM 25mW – 200mW





NOTE:




CH
FR
FR
FR1(A)
FR2(B)
FR3(C)
FR4(D)
FR5(E)
CHANNEL
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
 5760 5780 5800 5820  5860 5880
5705 5685 5665  5885 5905 5925 
5865  5825 5805 5785 5765  5725
5658 5695 5732 5769 5806  5880 5917
5733 5752 5771 5790 5809 5828  5866
2
18


AND TRANSMITTER








   
            
             

T
19

CC3D FLIGHT CONTROLLER SETUP USING
OPEN PILOT GCS SOFTWARE
WARNING! 













                
            

20