SKY-HERO Anakin Installation guide

Assembly
Instrucon Manual
2015.08

TABLES OF CONTENT
GLUE THE TUBES END’S 1
ATTACH YOUR MOTORS 2
ATTACH MOTOR MOUNTS ON ARMS 3
ROUTE YOUR MOTOR CABLES 4
FIX YOUR SIDE FRAME USING 2 SCREWS 4
SOLDER YOUR ESC’S 4
USE SCHRINK TUBE TO PROTECT YOUR ESC’S 4
SLIDE ESC’S INTO THE TUBES 4
PRESS THE INSERT IN POSITION 4
CHOOSE THE POSITION OF YOUR ARMS 9
SLIDE YOUR MOTOR SHAFTS INTO THE MOUNTING JIG 10
SCREW YOUR LOWER FRAME 11
FIX YOUR MOTOR MOUNT 12
ATTACH YOUR Z SPACERS 13
FIX YOUR CAMERA PLATE IN POSITION 14
CAMERA ANGLE 15
ADJUST MOTORS ANGLE 16
ATTACH YOUR CANOPY 17

SCREW 1/1 SCALE
ISO 7380 M3X6MM
ISO 7380 M3X4MM
ISO 7380 M3X6TP MM
ISO 7380 M3X30MM
ISO 7380 M2.5X8MM
HEX NUT 2.5MM

SKH01-106-F
SKH01-106-R
SKH03-280 ( FRONT TUBE )
(ou SKH03-240)
SKH03-280 (REAR TUBE
(ou SKH03-240 )
USE EPOXY
GLUE
USE EPOXY
GLUE
8MM
8MM
GLUE THE TUBES END’S
Use 5min epoxy glue
(Whipe out excess of glue with acetone)
1
Please make sure you push the


*
*
*
USE EPOXY
GLUE
FIG. 1

SKH04-009
SKH01-105
ISO 7380 M3x6MM
ATTACH YOUR MOTORS
Warning! Before starng:
- Make sure to idenfy your clockwise (CW) and counter-clockwise (CCW) motors*.
- Be aware that all your wires will go backwards as shown in gure 3
2
FIG. 2
FIG. 3
CW
CW
CCW
CCW
* 

CW CCW
CCW CW
3
BUILD 1CW+1CCW
FOR FRONT SIDE
BUILD 1CW+1CCW
FOR REAR SIDE
 (See gure)
1CW+1CCW
 1CW+1CCW
FIG. 4
FIG. 5
ATTACH MOTOR MOUNTS ON ARMS

a «clic»
(it can require quite an important pressure)

SKH03-280-A
OU ( SKH03-240-A )
( LEFT SIDE )
SKH01-170-00
(OPTION = SKH06-001)
ISO 7380
M3x8TP
ROUTE YOUR MOTOR CABLES
Rear cables = 220mm long / Front cables = 150mm long
FIX YOUR SIDE FRAME USING 2 SCREWS
Build le + right side
4
FIG. 6
FIG. 7

SKH04-014*


SOLDER YOUR ESC’S
And check your motors direcon

SKH04-014*
5
* 
USE SOLDER
& WELDING
FIG. 8
FIG. 9

SLIDE ESC’S INTO THE TUBES
6
FIG. 10

SKH03-200-S
SH54-03
(FROM SKH07-111)
SH54-01
(FROM SKH07-111)
SKH03-200-U
SH54-03
(FROM SKH07-111)
SKH03-200-U
PRESS THE INSERT IN POSITION
In order to mount the frame you must rst insert the PEM’s by ghtening them
one by one unl you reach themaximum posion.
Use the threaded insert on upper frame.
TIP:
Use 1 frame spacer + 1
M3x30MM screw, to press
your insert in posion
Once nished you will have this:
7
THREADED
NOT THREADED
SH54-03
FIG. 11

SLIDE YOUR FRAME SPACER AROUND THE TUBES
(Use the threaded insert on upper frame)
FRONT SPACER
REAR SPACER
SKH01-103-F SKH01-103-R
SKH01-103-F
SKH01-103-R


8
FIG. 13
FIG. 12

CHOOSE THE POSITION OF YOUR ARMS
ACCORDING THE CENTER OF GRAVITY ADJUSTMENT YOU WANT
FRONT SPACER REAR SPACER
SKH01-103-F SKH01-103-R
FRONT UP
LOW CG
CROSSED SETUP
HIGH CG
Standard setup
REAR UP
REAR UP
REAR DOWN
FRONT DOWN
FRONT DOWN
9
FIG. 14

SLIDE YOUR MOTOR SHAFTS INTO THMOUNTING JIG
10
FIG. 15

ISO7380 M3x30MM



SOLDER YOUR ESC CABLES, EQUIPEMENTS CABLES, ( VTX, UBEC, LED, ETC... )
TO YOUR BATTERY CONNECTOR CABLES
SCREW YOUR LOWER FRAME
(DO NOT OVERTIGHT)
BATTERY CONNECTOR
CABLES
EQUIPEMENTS
11
FIG. 16
FIG. 17

DIN912 M2,5x8MM
HEX NUT
M2,5x0,5MM
FIX YOUR MOTOR MOUNT
12
FIG. 18

ISO7380 M3X30MM

SCREW THE THIRD SCREW
13
FIG. 19


ISO7380 M3x6MM

ISO7380 M3x6 MM


ATTACH YOUR Z SPACERS


14
FIG. 20
FIG. 21
FIG. 22

CAMERA ANGLE
 angle of the camera
20 °
20 °
Standard setup
15
FIG. 23
FIG. 24
FIG. 25
* 
* Cam
* Cam
* Cam

ADJUST MOTORS ANGLE
banked posionplacc ring or alu ring

WARNING!oponal sideframes
website (www.sky-hero.com)
0°
10°
Standard setup
Banked setup
16
FIG. 26
FIG. 27




ATTACH YOUR CANOPY

17
FIG. 28