SKY-HERO Anakin User manual

Assembly
Instrucon Manual
2015.08

TABLE OF CONTENT
SCREWS 1/1 SCALE 1
GLUE THE TUBES END’S 2
ATTACH YOUR MOTORS 3
ATTACH MOTOR MOUNTS ON ARMS 4
ROUTE YOUR MOTOR CABLES 5
FIX YOUR SIDE FRAME USING 2 SCREWS 5
SOLDER YOUR ESC’S 6
SLIDE ESC’S INTO THE TUBES 7
PRESS THE INSERTS IN POSITION 8
SLIDE YOUR FRAME SPACER AROUND THE TUBES 9
CHOOSE THE POSITION OF YOUR ARMS 10
SLIDE YOUR MOTOR SHAFTS INTO THE MOUNTING JIG 11
SOLDER YOUR ESC CABLES, EQUIPEMENTS CABLES TO YOUR BATTERY CONNECTOR CABLES 12
SCREW YOUR LOWER FRAME 12
FIX YOUR MOTOR MOUNT 13
SCREW THE THIRD SCREW 14
ATTACH YOUR Z SPACERS 15
CAMERA ANGLE 16
ADJUST MOTORS ANGLE 17
EQUIPMENTS LAYOUT 18
ATTACH YOUR CANOPY 19

SCREWS 1/1 SCALE
ISO 7380 M3X6
ISO 7380 M3X4
ISO 7380 M3X6TP
ISO 7380 M3X8TP
ISO 7380 M3X30
DIN 912 M2.5X8
HEX NUT M2.5
1

SKH01-106-F
SKH01-106-R
SKH03-280 (FRONT TUBE)
SKH03-280 (REAR TUBE)
USE EPOXY
GLUE
USE EPOXY
GLUE
8MM
8MM
GLUE THE TUBES END’S
(Wipe out excess of glue with acetone)
2
Please make sure you push the
tube at the edge of the arm’s end
*
*
*
FIG. 1
USE 5MIN EPOXY
GLUE

SKH04-009
SKH01-105
ISO 7380 M3X6
ATTACH YOUR MOTORS
Warning!
(CW) and counter-clockwise (CCW) motors*.

3
FIG. 2
FIG. 3
CW
CW
CCW
CCW
* 

CW CCW
CCW CW
4
BUILD 1CW+1CCW
FOR FRONT SIDE
BUILD 1CW+1CCW
FOR REAR SIDE

You must build 1CW+1CCW with the motors’s wires oriented to the side of the nut for Anakin’s front side and
1CW+1CCW with the motors’s wires oriented to the side of the screw for Anakin’s rear side
FIG. 4
FIG. 5
ATTACH MOTOR MOUNTS ON ARMS

you hear a «clic» noise.


SKH03-280-A
(LEFT SIDE)
SKH01-170-00
(OPTION = SKH06-001)
ISO 7380
M3x8TP
ROUTE YOUR MOTOR CABLES
Rear cables = 220mm long / Front cables = 150mm long
FIX YOUR SIDE FRAME USING 2 SCREWS
B
5
FIG. 6
FIG. 7

SKH04-014*
Let the esc outside the tube and connect

SOLDER YOUR ESC’S
A
Use schrink tube to protect your esc’s
SKH04-014*
6
* 
FIG. 8
FIG. 9
USE SOLDER
& WELDING

SLIDE ESC’S INTO THE TUBES
7
FIG. 10

SKH03-200-S
SH54-03
(FROM SKH07-111)
SH54-01
(FROM SKH07-111)
SKH03-200-U
SH54-03
(FROM SKH07-111)
SKH03-200-U
PRESS THE INSERTS IN POSITION



TIP:
U
M3x30 screw, to press 2

Repeat process for each
PEM’s

crimped as shown in 
8
THREADED
NOT THREADED
SH54-03
FIG. 11
FIG. 12

SLIDE YOUR FRAME SPACER AROUND THE TUBES
se the threaded insert on upper frame)
FRONT SPACER
REAR SPACER
SKH01-103-F SKH01-103-R
SKH01-103-F
SKH01-103-R


9
FIG. 14
FIG. 13

CHOOSE THE POSITION OF YOUR ARMS
ACCORDING THE CENTER OF GRAVITY ADJUSTMENT YOU WANT
FRONT SPACER REAR SPACER
SKH01-103-F SKH01-103-R
FRONT UP
LOW CG
CROSSED SETUP
HIGH CG
REAR UP
REAR UP
REAR DOWN
FRONT DOWN
FRONT DOWN
10
FIG. 15
Standard setup

SLIDE YOUR MOTOR SHAFTS INTO THE MOUNTING JIG
11
FIG. 16

ISO7380 M3X30




TO YOUR BATTERY CONNECTOR CABLES
SCREW YOUR LOWER FRAME

BATTERY CONNECTOR
CABLES
EQUIPEMENTS
12
FIG. 17
FIG. 18
TIP:
PEM’s are already pressed in


DIN912 M2,5X8
HEX NUT
M2,5X0,5
FIX YOUR MOTOR MOUNT
13
FIG. 19

ISO7380 M3X8TP

SCREW THE THIRD SCREW
14
FIG. 20


ISO7380 M3X6TP

ISO7380 M3X6


ATTACH YOUR Z SPACERS
Fix your camera plate

15
FIG. 21
FIG. 22
FIG. 23

CAMERA ANGLE
YOU CAN ADJUST THE ANGLE OF THE CAMERA AS FOLLOWED
20 °
20 °
Standard setup
16
FIG. 24
FIG. 25
FIG. 26
* 
*
*
*

Standard setup
ADJUST MOTORS ANGLE
To adjust motor angle to  or 
*.
*You need 
()to order them or run to the closest Sky-Hero dealer!
0°
10°
17
FIG. 27
FIG. 28
Banked setup

EQUIPMENTS LAYOUT
18
YOUR VIDEO
TRANSMITTER

FIG. 29
* 
*
*