Sky R6 User manual

1. The pouch laminator must be connected to a supply voltage
corresponding to the electrical rating of the machine as indicated.
2. Unplug the pouch laminator before moving it, or when it is not in use for
an extended period of time.
3. Do not operate with a damaged supply cord or plug, after it
malfunctions, or after it has been damaged in any manner.
4. Do not overload electrical outlets beyond their capacity as this can
result in fire or electrical shock.
5. Do not alter attachment plug, plug is configured for the appropriate
electrical supply.
6. The unit is intended for indoor use only.
1 Specifications
2 Electrical Safeguards
3 Trouble Shooting Guide
4 After Sales Service Information
Max. Laminating Width 335 mm 490 mm
Max. Laminating Speed 1400 mm 1200 mm
Max. Pouch Thickness 350 MIC
Max. Laminating Thickness 3 mm
Heating System Heating roller internal heater
Qty of Roller 6
Operating Temp. 0- 140
Temperature & Speed Control Yes
Preheating Time 6 mins
Power Consumption 1150 watt
Rating 230V / 60Hz / 6A
Dimension 536 x 271 x 112 / 15kg 690 x 271 x 112 / 20kg
Machine has no
power or rollers are
not rolling
Excessive noise
Bad lamination
No increase of Temp
Corner is not sealed
Emergency state
Power code is not
properly plugged in
Power switch off
Operation of gear is not
smooth.
Laminated document
wrinkled, damp, or folded
Check power plug
Document is too thick to
seal the edges of the film
Something may be stuck
Between the heated
rollers or they are out of
position
Check the power plug
is properly plugged
Check the power
switch is turned on
or contact support
Turn off the machine,
and then contact A/S
Adjust the temperature
lower or higher
Check if the power plug
and switch is turned on
or contact support
Use a thinner document
or leave more around
the edges, aprox. 5mm
Turn off the switch
Contact A/S
If you have any problem can not be solved at your end, please contact;
The telephone number is on the label on the back side of machine.
2 3
Problem Cause Solution

Hot
Mode
icon
Cooling
Fan
icon
Roller
Operation
icon
Cold
Mode
icon
Curreut
Temperature
icon
POWER :For On and Off, Press Power button for 1 second.
HOT :Start Hot Lamination.
COLD :Start Cold Lamination
TEMP :Modify temperature(0~140 C)
SPEED :1 ~ 9 Steps
M1, M2 :Memory function set in production.
MEAS :Display actual roller temp.
RUN/STOP :Run and stop roller operation
REV :Reverse
1. Do not allow neckties, scarves, etc
near front or rear machine openings
as they could get caught by rollers
and be pulled inside, causing
serious personal injury.
2. To prevent possibility of electrical
shock, do not immerse machine in
water or permit liquid to spill inside.
3. Close supervision is necessary
when any appliance is used by
or near children
4. Do not open the cover (or back)
without authorized service-
man.
5. The socket-outlet shall be
installed near the equipment
and shall be easily accessible.
Disconnect the attachment
plug from the receptacle to
which it is connected and keep
the power supply cord in your
possession while moving the
laminator.
4 5
5 Location and Function of Control 6 Trouble Shooting Guide

Film
Thickness
(mic)
75~100
125~150
175~250
Paper Temp
(C)
Speed
A2/A3 A4
Temp
(C)
Speed
A2/A3 A4
Setting without Carrier Setting with Carrier
Copy Paper (80gsm)
Art Paper (120gsm)
Hard Paper (200gsm)
If user use a low temperature film, please decrease 15~20
To avoid machine damaged, please set suitable temperature and speed.
To avoid machine damaged, please set suitable temperature and speed.
100
100
100
120
120
130
120
140
140
6
5
4
4
3
3
3
2
1
7
6
5
5
4
4
4
2
2
4
4
3
3
3
2
2
2
1
5
5
4
4
4
3
3
3
2
130
130
130
130
140
140
140
140
140
Copy Paper (80gsm)
Art Paper (120gsm)
Hard Paper (200gsm)
Copy Paper (80gsm)
Art Paper (120gsm)
Hard Paper (200gsm)
Film Entry Main Switch Power cord inlet
LCD Display Film exit
1. Turn the switch on
2. If it is not the first use,
Press POWER button for 1 second.
Press HOT button.
Initial setting for 100 MIC is 100 , speed 6.
Hot mode icon flickers.
3. When it's ready, there will be beep sound for 3 times.
You can start to laminate.
Warning - Insert the sealing of film forward.
4. Beginning lamination
- If user wishes to laminate faster: User can
increase the speed (the step of 1~9)
- When adhesion of lamination is not satisfactory,
increase the temperature.
5. Finishing lamination
Press POWER button for 1 second.
Once it reaches below 65 C the power stops automatically.
(Keep the temperature 80 C and speed 2 for STAND BY mode.)
Warning
Do not turn off the Switch as soon as finishing lamination to
prevent overheating. Follow the Upper method. After the roller cool
down, there will be beep sound for 5 times and then power will be
stopped automatically.
6. Cold lamination
Press COLD button.
- When the READY lamp indicates on LCD with beep sound, user
can start laminating. (User can use cold film only.)
- If user afraid to damage on material, should use COLD lamination.
6 7
7 Lamination Guide 9 How to Use
8 Description