Skyfood Fleetwood PC-8 User manual

Office
Phone: [phone]
Fax: [phone]
Warehouse
Phone: [phone]
Fax: [phone]
www.skyfood.us[email protected] -
TOLL FREE 1-800-503-7534
UG0113 - August /2013
Instructions Manual
Pop Corn
Model
PC-8

SUMMARY
1-
2-
3-
4-
5-
Function and features
Specifications
Transportation and storage
Cautions
Operation
6-Cleanliness and protection
Troubleshooting guides
Electrical Diagram
7-
8-
9-General safety practices
1
1
2
2
2
2
3
3
4

01
1- Function and features:
The popcorn machine combines all the advantages of the popcorn machines both in and abroad. It
is made of aluminum alloy and toughened glass, with a sprayed inattentive interior coat. The
machine also has the features of cleanliness and sanitation, easy cleaning, simple and safe operation
and saving energy, which is fit for restaurants, snack bars, cinemas and so on.
2- Specifications:
MODEL PC-8
Power (V) 110V~
Output
(kW)
1.4
Frequency
(Hz)
50/60
Temperatu
re (℃)
220~270
Formal
Size (mm)
1 9” 11/16x14”1
9 /32x27”9/16
Casing Size
(mm)
2 1”9 /32x15”3/4
x27” 9/ 16
Oil Dosage
(ml/once)
50
Sugar
Dosage
(g/once)
100
Corn
Dosage
(g/once)
150
Efficiency
(pan/min)
1/2
Net weight
Shipping
Weight
62lb
75lb

02
3- Transportation and Storage:
When being transported, be careful not to shake the machine violently; do not put it outdoors or in the direct
sunlight. If so, avoid rainfall; Store it in ventilated places out of erosive gases; do not put it up-side-down.
4- Cautions:
1. The machine should be laid up flat and stable.
2. The machine must be used together with the suitable power source suggested by the factory, that
power+10%(V).
3. Suitable switch, fuse box and the leak electricity switch should be fixed near the machine,
without piled up rubbish to make it convenient to operate.
4. The ground wire and the power source wire should come from the same place, connected with a
safe three-pin plug in the outlet.
5. All the connection with electricity should be done by the qualified electrician.
5-Operation:
1. Turn on the switch of heat preservation to start the heat tube and light.
2. Turn the heating knob to preheat the plate for 5~6 minutes.
3. Put 1.7 fl.oz (50ml )oil,5.2 oz (150g) corn and 3.5 oz (100g) sugar into the plate, and the corn will burst
open.
4. Pay attention to the corn while popping in case it will be burnt. Close the door firmly so that the corn can not
come out.
5. Stir the corn until it is all burst open, then pour it out from the plate.
6. Repeat 1~5 to make more popcorn. It needs only 2 minutes to pop the corn continuously.
7. Do not drop any oil around the plate. Otherwise it will catch fire when it is heated to a certain temperature.
Warning: Do not add any water to the plate while it is popping!
6-Cleanliness and Protection:
1. Cut off the electricity power and pull out the plug to avoid accidents when you clean the machine.
2. Use the wet towel with some anticorrosive detergent to clean the outside parts of the machine. Do not clean
the machine directly with water. Otherwise the electric function will be damaged.
3. If it is not used for a long time, you should cut off the electricity and pull out the plug.
4. Do not brush the inside part of the plate with hard metal. Otherwise you will damage the coat.

03
7- Troubleshooting guides:
Sequence Problem Causes Possible remedies
1 Light not on Not plugged in outlet fasten the screw of connecting the
wires
change the light bulb
2 Can not heat loose in wire of the heated
tube
heated tube burnt
broken electric capacity
fasten the screw from which the
wires come out.
change the heated tube.
change the electric capacity
3 Too high or
too low
temperature
Broken thermostat Change the thermostat
Appendix to the machine: 1. an operation manual
2. a bulb
8- Electrical Diagram
K1:POWER SWITCH
K2:HEATING/LIGHTING SWITCH
K3:MOTER SWITCH
K4:POT HEATING SWITCH
R1:HEATING ELEMENT FOR KEEPING WARM
R2:POT HEATING ELEMENT
BT1/BT2:TEMPERATURE LIMITER
HL:LAMP
M:MOTOR

9-General Safety Practices
The following safety instructions are addressed to both the operator of the
machine as well as the person in charge of maintenance.
The machine has to be delivered to the operator in perfect conditions of use by
the Distributor to the user. The user shall operate the machine only after being well
acquainted with the safety procedures described in the present manual. READ THIS
MANUAL WITH ATTENTION.
Basic Operation Practices
Dangerous parts
Some parts of the electric devices are connected to high voltage points.
These parts when touched may cause severe electrical shocks or even be fatal.
Never touch commands such as buttons, switches and knobs with wet hands, wet
clothes and/or shoes. By not following these instructions operator could be exposed to
severe electrical shocks or even to a fatal situation.
Warnings
The operator has to be well familiar with the position of ON/OFF Switch to make
sure the Switch is easy to be reached when necessary. Before any kind of maintenance,
physically remove plug from the socket.
Provide space for a comfortable operation thus avoiding accidents.
Water or oil spilled on the floor will turn it slippery and dangerous. Make sure the floor is
clean and dry.
Before giving any manual command (switch, buttons, turn keys or lever) be sure
the command is the correct one. Check this manual for further details if necessary.
Never use a manual command (switch, buttons, lever) unadvisedly.
If any work is to be made by two or more persons, coordination signs will have to be given
for each operation step. Every step of the operation shall be taken only if the sign has
been made and responded.
Advices
In case of power shortage, immediately turn the machine OFF.
Use recommended or equivalent lubricants, oils or greases.
Avoid mechanical shocks as they may cause failures or malfunction.
Avoid penetration of water, dirt or dust into mechanical or electrical components
of the machine.
DO NOT modify original characteristics of the machine.
DO NOT remove, tear off or maculate any labels stuck on the machine. If any
label has been removed or is no longer legible, contact your nearest dealer for
replacement.
IMPORTANT
If any item from the GENERAL SAFETY NOTIONS section is not applicable to
your product, please disregard it.
04
This product will be replaced or repaired under warranty, for a period of (6) months,
beginning from the date of purchase by the original purchaser/user (“End User”), or
eighteen (18) months from the date of shipment from SKYFOOD’s warehouse,
whichever expires first.
Accessories will be replaced or repaired under warranty, for a period of (30) days,
beginning from the date of purcha se by the original purchaser/user (“End User”), or
eighteen (18) months from the date of shipment from SKYFOOD’s warehouse, whichever
expires first.
This warranty shall not take effect until a properly completed and executed WARRANTY
REGISTRATION form has been received by SKYFOOD EQUIPMENT, LLC, within thirty
(30) days from the da te of purch ase. The WARRANTY REGISTRATION is available either
in the Instruction Manual of every Product or at SKYFOOD’s website www.skyfood.us. The
End User must fill out the WARRANTY REGISTRATION form and send it to SK YFOOD
according to the instructions p osted on the referred website. Failure to do so will VOID
the warranty.
No extended warranties for third party products. There are no other express
warranties or conditions other than the one offered by each manufacturer for
products sold by SKYFOOD, not under the FLEETWOOD by SKYMSEN and
SKYMSEN brand.
For questions or assistance, do not return the product or accessories to the store, please
call Toll Free 1-800-503-7534, or visit the Customer Service section at www.skyfood.us.
For faster service please have the items name, serial number, and proof of purchase for
the operator to assist you.
SKYFOOD reserve s the right to change the terms of its limited warranty at any time
without any prior notice. It also reserves the right to change the design and
specifications of its equipment or any related documentation at any time. The end
user is not entitled to upgrades or refunds resulting from these changes.
Updates
These Terms and Conditions were last updated on January 14th, 2014.

SAFETY PROCEDURES AND NOTES BEFORE SWITCHING ON
IMPORTANT
Carefully read ALL INSTRUCTIONS of this manual before turning the machine ON.
Be sure to be familiar with the instructions and that you have well understood all
information contained in this manual. If you have any question contact your
supervisor or your nearest Dealer.
Danger
An electric cable or electric wire with damaged jacket or bad insulation could
cause electrical shocks as well as electrical leak. Before use, check conditions of all
wires and cables.
Advices
Be sure ALL INSTRUCTIONS in this manual have been thoroughly understood.
Every function and operational procedure have to be very clear to the operator.
Contact your nearest Dealer for further questions.
Any manual command (switch, button or lever) shall be given only after being
sure it is the correct one.
Precautions
The electric cable has to be compatible with the power required by the machine.
Cables touching the floor or close to the machine need to be protected against short
circuits.
AFTER THE WORK ENDS
Cares
Always clean the machine, to do the cleaning SWITCH IT OFF, AND TAKE
OUT THE PLUG FROM THE ELECTRICITY SUPPLY SOCKET .
Never clean the machine BEFORE IT IS COMPLETELY STOPED.
Fit all the machine components in their due places, before switching it on
again.
MAINTENANCE
Dangers
Any maintenance is dangerous if made with the machine switched on.
SWITCH IT OFF AND TAKE OUT THE PLUG FROM THE SOCKET, DURING
ALL THE MAINTENANCE OPERATION.
IMPORTANT
In any emergency situation, always take the plug out of its socket.
CEADVI S
e t c lrc a i mt n eb u ie es n .
El c ri ao me h n cal ain ena c shall e made by q alif d p r o s
s n in cam t n n e prel h c mwsThe per o hrge of the ain e a c eformanc s shal c e k the achine ork
OLF Y D T O .under T TASA ET CON I I NS
05
SKYFOOD EQUIPMENT LLC - SERVICE
For questions or assistance, call SKYFOOD EQUIPMENT Toll Free: 1-800-503-7534, or
visit the Customer Service section at www.skyfood.us.
SKYFOOD’S LIMITED WARRANTY
Unless otherwise specified,new FLEETWOOD by SKYMSEN and SKYMSEN products,
excluding accessories, sold by SKYFOOD EQUIPMENT, LLC. (“SKYFOOD”), for use only
in the continental United States (collectively, “Products” or singularly, “Product”), are
warranted to be free from defects in materials an d workmanship for a period of one (1)
year from the date of purchase by the original purchaser/user (“End User”), or eighteen
(18) months from the date of shipment from SKYFOOD’s warehouse, whichever expires
first. Several new products and accessories may be warr anted for a p eri od other than o ne
(1) year while others may be subject to travel li mitations, as specified on the products
Instruction Manual. Proof of purchase must be presented; if not this warranty will be
VOID. No warranty is given or implie d to a subsequent transferee or any other third party.
This warranty is expressly conditional up on SKYFOOD being notified of any defects in
materials or workmanship with in five (5) days of its occurrence, wi thin the warranted time
period. If a notice of a claim under this warranty is timely made by the End User,
SKYFOOD or a SKYFOOD’s designated service company (“Service Company”), will rep air
or replace the Product, at SKYFOOD’s discretion, subject to the additional conditions
hereinafter described.
This warranty shall not apply if damage occurs from improper installation or maintenance
performed by an unauthorized service company (“Service Company”), wrong voltage, nor
to the extent that Products or parts have been used other than in conformance with
operating and maintenance instructions, subjected to misuse or abuse or damaged by
accident, acts of God, a bnormal use, stress or any other matter unrelated to SKYFOOD,
and beyond its reasonable control. This warranty does NOT cover s ervice labor and
travel to perform adjustments on products and/or accessories. In addition to wear and
tear of certain items, such as, but not limited to; glass parts, blades, stones, chopp er
cutting knives, plates, slicing knives, cutting disc, gaskets, oil changes, sealing tape, heat
seal wires, worm gears, self-lubricating bushings, carbon brushes for electric motors, a nd
other parts expendable by nature and that need to be replaced frequently. Electrical
components are subject to natural wear and tear, and are NOT covered by this
warranty. THIS WARRANTY EXCLUDES ALL ORAL, STATUTORY, EXPRESS OR
IMPLIED WARRANTIES WHICH MAY BE APPLICABLE TO SKYFOOD, INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY AND
FITNESS FOR PARTICULAR PURPOSE. Under no circumstances shall SKYFOOD be
liable for loss of use, revenue o r profit or for incidental or consequential damages.
SKYFOOD shall under no circumstances be liable for any loss, damage, concealed
damage, expense or delay of goods for any reason when said goods are in the custod y,
possession or control of third parties selected by SKYFOOD to forward, e nter, clear,
transport, or render other services with respect to such goods. The sole and exclusive
remedy for breach of any warranty is limited to the remedies provided in the paragra ph
above.
All products held at non-commercial facilities or domiciles, must be taken or shipped,
shipping charges prepaid, either to SKYFOOD's facility or a SKYFOOD's designated
service company ("Service Company"). Products held at commercial facilities and weighing