SkyVac spinAclean 85 User manual

SKYVAC INDUSTRIAL 85 WITH ELITE POLES
Assembly
Instrucons
SkyVac Industrial 85
with Elite Poles
Including Elite Vac
Release Pole
(SkyCam Sold Separately)
AREAS OF INSTRUCTION:
1. FILTER & HOSE
2. SWITCH SEQUENCE - POWERMIX & TILTING DRUM
3. TOOLS AND USAGE
4. POLES AND INSERTION
5. POLES AND OTHER INSERTIONS
6. VAC RELEASE POLE USAGE
7. SKYCAM MOUNTING (EXTRA PURCHASE)
8. MACHINE MAINTENANCE AND TIPS
9. REMOVAL OF DRUM
10. TROUBLESHOOTING GUIDE
11. ACCESSORIES

SKYVAC INDUSTRIAL 85 WITH ELITE POLES
1. FILTER & HOSE
Always use the Filter to protect the Motor
Clean lter on a regular basis.
The lter is washable, for best
results allow lter to dry
before use. Make sure pleats
are clear of debris.
Make sure the switches rest in
front of the handle so the
deector plate in front of the
lter is in the correct posion.
Push the exi hose hard vac cu
into vacuum port.
2. SWITCH SEQUENCE - POWERMIX & TILTING DRUM
Only use POWERMIX when needed, to prevent overheang Motors
Always switch white middle
buon on rst, followed by
either red motor.
For maximum sucon power
acvate all three motors.
Slide to the right for sucking
up water and liing heavy
tus of grass.
All other mes keep far le.
This seng will avoid over
heang the motors.
To empty SkyVac remove the head
and lt the bin forward.

SKYVAC INDUSTRIAL 85 WITH ELITE POLES
3. TOOLS AND USAGE
SkyVac have tools for every task (please enquire)
Insert the carbon bre tool
holder.
Adjust the tension of the clamp
Adjust the tension of the clamp
by twisng it clockwise.
Insert your chosen tool unl
total resistance.
4. POLES AND INSERTION
Aaching poles together
Open clamp up and insert pole. Insert the pole up to the
posive stop and no further.
Adjust tension of clamp and close
o.

SKYVAC INDUSTRIAL 85 WITH ELITE POLES
5. POLES AND OTHER INSERTIONS
Push the so hose cu over your base pole (vac release
pole).
Build your poles up against the wall.
Lean them against the wall with logo facing upwards. Fit
your selected end tool on the top pole rst then feather
the poles upwards unl you reach your desired height.
6. VAC RELEASE POLE USAGE
Speed up your guer cleaning
Your carbon poles are extremely strong. However avoid over straining/bending them when handling
heavy grass deposits when cleaning 6 plus poles high. Best pracce to remove heavy tus of grass
from guers is chop down to manageable lengths.
Place sucon end tool on grass tu and li away from guer and open up Vac Release door to cut the
vacuum this will release grass from end tool.
IMPORTANT: Ensure you can drop the grass safely to the ground.

SKYVAC INDUSTRIAL 85 WITH ELITE POLES
7. SKYCAM MOUNTING
SkyCam Sold Separately
SkyCam Instrucons
Press the buon behind the
water proof boot to switch the
camera on. A light will come on
once you’ve turned the camera
on.
See camera instrucon manual
for full user guide.
Aach the camera using spring
clip to the blue exi neck tool
holder.
Pre inspect the guer to deter-
mine which tool to use, and
problem areas.
Remove camera when vacuum-
ing to prevent damage to
equipment.
Aach monitor to you’re base
pole, at eye level using spring
pole clip.
Switch monitor on, which auto-
macally connects to the camera.
Once completed vacuuming, re-
aach camera to do nal checks.
8. MACHINE MAINTENANCE
Look aer your equipment
Aer every shi, ush the
inside of tubes and exi
hose by sucking half a
bucket of water up into
the vacuum and empty.
This help keep the pole
joints clean from grit.
Always clean your poles to ensure
the joints are clean and free from
grit/dirt which may prematurely
wear the joints.
TIP: During cleaning wet or damp
guers, dirt can somemes sck
and line the inside of your poles.
The poles will get cold to touch and
the weight of the poles will be in-
creased slightly. To remedy this
place the end tool in water and
suck up a small amount of water.

SKYVAC INDUSTRIAL 85 WITH ELITE POLES
9. DRUM REMOVAL FOR CLEANING
Look aer your equipment
Turn red knob upwards. Li drum o trolley. Clip locks back into posion.
10. TROUBLESHOOTING
Symptom Possible Cause Remedy
Poor Sucon Blocked lter or full bin Clean lter and empty bin
Poor Sucon Blockages in exi neck or poles or Vac
entrance
Clear blockages
Poor Sucon Leaves blocking at end tool Tap leaves & end tool on roof les
Poor Sucon Blocked exi neck Place end tool on roof and gently pull
down to slightly straighten exi bend
to unblock
Poor Sucon Damp debris build up inside exi hose
of tubes
Suck water from bucket as per above
image
Sucon not powerful
enough
Vac power switch is selecng 1 motor
only
Select both motors
Camera screen frozen Lock out Select reset buon on back of moni-
tor
Machine stopped working Over heated Clean lter leave machine to cool
down for 10 minutes. Move power
mix lever full le
Machine stopped working Loss of power Check power supply
Machine stopped working Too many extension leads or incorrect
gauge DIY extension
Always use heavy duty extension
leads

SKYVAC INDUSTRIAL 85 WITH ELITE POLES
11. ACCESSORIES
Accessories as Standard Descripon
SkyVac Industrial 85 (all end tools listed are compable with the Elite Carbon Fibre Poles)
Aluminium Crevice End Tool Ideal for gaining access to narrow and ght spaces
when roof les encroach over and into the guers.
Eecve and thorough cleaning for those tough to
access areas.
Aluminium Standard Dirt
Breaker
Breaks down dirt, debris, and grass for easier clean-
ing. Ideal for making those everyday cleaning tasks
quicker and easier. Strong aluminium makes it dura-
ble enough to use every day.
Aluminium Reducer Tool Allows for more accurate cleaning because of its
tapered end. Ideal for harder to reach areas of the
guer and precise cleaning of debris and leaves in
the guer.
Daily End Tool The essenal accessory for all your daily cleaning
needs. Eecvely breaks down debris in the guer
for easy cleaning, with an extra wide entry point to
reduce the chance of blockages.
Aluminium Long End Tool This tool is used for daily guer cleaning tasks, and
breaks up the dirt for easier sucon. It has that ex-
tra length for deeper guers and downpipes for
more thorough cleaning in harder to reach spaces.
Rigid Neck Tool Strong, durable, and the perfect angle for all your
guer cleaning needs. Allows you to aach a wide
variety of aluminium end tools to your Elite Poles,
for a completely customisable clean.