DIVERSITECH DrainKat MBK-6 User manual

CO2and Nitrogen Filling
CARBON DIOXIDE (CO2) FILLING:
1. Disconnect hose and unscrew regulator from the DrainKat.
2. Turn over and vent o any remaining contents from the DrainKat. This can be an
eective way to pre-chill the cylinder – see warning below.
3. Weigh the small cylinder, and record the tare weight.
OPERATOR’S TIP: Slightly open the valve of the parent cylinder at this point to
vent o any vaporized CO2in the dip tube. Within 5 seconds a white snow like
discharge indicates liquid CO2is available to be translled. Vapor type cylinders
will have to be inverted to extract liquid. (See illustration #2.)
MBK-6 DrainKat™
Instructions
The MBK-6 DrainKat™ condensate
drain line cleaning kit uses a dry
nitrogen or CO2charge to clear
drain line clogs. The Drain Kat
also uses the included blow gun
in conjunction with the QN-S3
to clean o dirt and debris from
HVAC coils.
FILLING
FROM:
PARENT CO
2
DIP TUBE
CYLINDER
DIP TUBE or SIPHON TUBE
VAPOR CARBON DIOXIDE (CO2)
LIQUID CARBON DIOXIDE (CO2)
FA-03 CO2x CO2ADAPTOR
DRAIN KAT
llustration #1

4. Connect the DrainKat to the parent cylinder using the FA-03 adaptor.
(See illustrations #1 & 2)
WARNING: Colder cylinders accept more CO2while lling.
Cylinders that are cold or that have been pre-chilled before being lled
must be weighed to conrm they are not overlled.
5. With cylinders hand tightened together, open the DrainKat, then slowly open the
parent cylinder allowing pressure to equalize.
6. When ow stops, close both cylinder valves, and disconnect the cylinders by
unscrewing the adaptor.
7. There will be a slight release of gas between the two cylinders upon disconnecting.
8. Re-weigh the DrainKat, and subtract the tare weight. This is the contents weight.
9. Check the contents against the rated capacity of the Drain Kat usually stamped
into the neck of the cylinder. If the cylinder is overlled, release the excess
contents immediately.
WARNING: OVERFILLED CYLINDERS ARE DANGEROUS!
Always check contents weight on an accurate scale.
NITROGEN FILLING:
1. Disconnect hose and unscrew regulator from the DrainKat.
2. Connect FA-03 and FA-01 adaptors onto the DrainKat cylinder valve.
(See illustration #3)
3. Connect the DrainKat onto the larger nitrogen cylinder (mother cylinder).
4. Open the DrainKat, then slowly open the parent cylinder allowing pressure to
equalize.
5. Completely close both cylinder valves, and disconnect the cylinders by
unscrewing the adaptors.
6. There will be a slight release of gas between the two cylinders upon disconnecting.
7. Check for continuous leaks.
CAUTION: This equalizing transll does not overll the DrainKat when using a
standard 2015 psi 40 Cu.Ft. or 80 Cu.Ft. parent cylinder. Larger capacity or higher
pressure parent cylinders require the use of a system to prevent pressures over
1800 psi from entering the DrainKat.
FILLING
FROM:
CO
2
VAPOR
CYLINDER
VAPOR CARBON DIOXIDE (CO2)
LIQUID CARBON DIOXIDE (CO2)
DRAIN KAT
FA-03 CO2x CO2ADAPTOR
llustration #2

FILLING
FROM:
PARENT
NITROGEN
CYLINDER
DRAIN KAT
llustration #3
FA-03 CO2to CO2ADAPTOR
FA-01 NITROGEN to CO2ADAPTOR
FA-01
M x M Nitrogen to CO2Adapter
FA-03
F x F CO2to CO2Adapter
Warnings
• This product contains chemicals, including lead, or otherwise known to the State
of California to cause cancer, birth defects, and other reproductive harm. Wash
hands aer handling (California Health & Safety Code § 25249.5 et seq.)
• Caution: cylinders are highly pressurized. Always handle with care. Never allow
cylinders to be dropped, knocked over or subjected to excessive heat.
• Never stand in front of or behind a regulator or tank when opening the cylinder
valve. Always stand so that the cylinder is between you and the regulator.
• Do not use the regulator if there are any damaged parts on the regulator, cylinder,
or valve.
• Regulator outlet pressure must not be greater than 400 psi when using the blow
gun. This is the maximum pressure rating for the blow gun. Regulator outlet pressure
must not exceed 30 psi when using the QN-S3 tip.
Included Accessories
QN-S3
This accessory is used to remove compressed dirt and debris from
a coil. To use this accessory, connect the QN-S3 to the tip of the
blow gun. Do not exceed 30psi. C02or Nitrogen can be used.
QN-S3
BLOW GUN
HOSE FROM
DRAINKATTM

DOC39572
6650 Sugarloaf Parkway #100
Duluth, GA 30097
[phone] diversitech.com
DF-75 DrainDawg
This item can be used to clear clogs in drain pipes. In order to use this
accessory, the included CW-15 short red hose must be connected to the
blow gun of the DrainKat. To connect the CW-15 hose, rotate the stationary
end of the CW-15 hose around the blow gun tip then connect the rotatable
end of the red hose to the DF-75 DrainDawg. Do not exceed 140psi with
the DF-75. The DF-75 is only to be used with ¾”-1” diameter pipe.
CB-03
The CB-03 can be used with other pipe sizes that may not work with the
DF-75 DrainDawg. To use this accessory, connect the CB-03 to the tip of the
blow gun. Do not exceed 100psi. C02or Nitrogen can be used.
Included Accessories (cont.)
CW-15
DF-75
BLOW GUN
HOSE FROM
DRAINKATTM
SWIVEL END
NON-SWIVEL END
CB-03
BLOW GUN
HOSE FROM
DRAINKATTM
SWIVEL END
CW-15
This small section of red hose (whip hose) connects to the tip of the blow
gun and then to the DF-75 DrainDawg.
©2013 DiversiTech
When using the DrainDawg accessory to clear a drain line, be sure to insert the
DrainDawg fully into the pipe.
PVC DRAIN PIPE
PVC DRAIN PIPE