Butler's Choice BC6115BK User manual

POWER NOZZLE
MODEL: BC6115BK TYPE: DS1601

Parts List
1
2
3
4
5
6
WARNING
Contents
Assembly
Opertion
Maitenane
troubleshooting

1
IMPORTANT
SAFETY INSTRUCTIONS!
WARNING!
To reduce the risk of fire,
electric shock, or injury:
when using an electrical appliance, basic precautions
should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS UNIT
- Close supervision is necessary when any appliance is used by or near
children. Do not allow your Power nozzle to be used as a toy or to run
unsupervised at any time.
- Unplug the cord when not in use. Do not run appliance over cord. Keep cord
away from heated surfaces. Do not use with damaged cord or plug.
- Do not leave appliance when plugged in. Unplug cord from outlet when not
attended and before servicing.
- If the Power nozzle is in disrepair, do not, attempt to operate it. If appliance is
not working as it should, has been dropped, damaged, left outdoors or dropped
into water, return it to a service centre for check-up or repair.
- Do not put any objects into openings. Do not use with any openings blocked.
Keep free of dust, lint, hair, or anything that may reduce airflow.
- The Power nozzle contains a powerful revolving brush. Keep hair, jewelry,
loose clothing, fingers, feet and all parts of body away from openings, rotating
agitator and other moving parts.
- Use extra care when cleaning on stairs.
- Do not use the power nozzle on people or animals.
- Do not pick up anything that is burning or smoking, such as cigarettes,
matches, or hot ashes; Do not use to pick up flammable or combustible liquids,
such as gasoline, or use in areas where they may be present.
- Never use Power nozzle to pick up water or any other fluids. This could
impair the electrical safety of the appliance.
- Do not use if damaged, cut or punctured.
- Avoid picking up hard or sharp objects, they could cause a blockage and
damage the Power nozzle.
- Do not allow the power nozzle to get wet. Clean only with a dry or slightly
damp cloth. If any moisture gets into the appliance, danger of electric shock.
- Do not use the power nozzle to suck up water; Do not immerse in water for
cleaning.
- Always turn off this appliance before connecting or disconnecting either the
hose of motorized nozzle.
SAVE THESE INSTRUCTIONS

2
Parts List
1.Wheel cover plate
5.Furniture guard
9.Rear wheel
13.LED PCB
17.Rocker arm
21.Height adjusting wheel
25.Height adjustment foot pedal
29.Wire cover plate
33.Locking lever
37.Headlight window
41.Base plate
2.Front wheel
6.Sleeve bearing
10.Brush roller
14.Height adjustment display window
18.Rocker arm pivot
22.Number tape
26.Intake socket
30.Spring retainer ring
34.Locking lever spring
38.Motor
42.Power cord
3.C-Clip
7.Rear wheel shaft
11.Main PCB
15.Locking lever pivot
19.Height adjusting wheel spring
23.Ratchet wheel
27.Swivel neck
31.Intake socket lock release pedal
35.Power indicator lamp cover
39.Belt
4.Front wheel axle
8.E-Clip
12.Air duct partition plate
16.Rocker arm spring
20.Locating elastic part
24.Pedal fix block
28.Intake socket cover plate
32.Lock release pedal retaining plate
36.Top cover
40.Sealing felt

3
Assembly
Operation
POWER NOZZLE ASSEMBLY
1.Push the wand
into the swivel neck
of the power head
until it clicks into
place.
2.Fix the cord to the wand.
3.Connect the wand with the hose
handle and plug the cord into the
receptacle on the hose handle.
1.Step on the lock release pedal (located on the left
side) and release the tube.
Return the tube back to the upright position to lock it
when not in use.
Note: Pull the tube by force without step on the lock
release pedal may damage the intake socket lock
system.
2.Step on the height adjustment
foot pedal (located on the right
side) until the desired brush roller
height is showed in the display
window.

4
Operation
Warning: Always disconnect the unit from electrical supply before serving.
Maitenane
The power nozzle designed with 5
height adjustment level. Choose an
appropriate height level for different
floor.
Level 1 – shortest distance from the
floor
Level 5 – highest distance from the
floor
3.Press the switch located in the hose
handle to turn the power nozzle on and
navigate the power nozzle back and
forth to work.
REPLACE BRUSH ROLLER AND BELT
1.Remove 8 screws from the bottom,
then turn the unit over, release the
intake socket and remove the top cover.
2.Lift out the brush roller and belt

Maitenane
5
3.Loop the new belt over the
motor pulley first, and place
the opposite end of the belt on
the brush roll pulley
4.Place the brush roller into
the bottom base with the
round edge of the two
end-caps facing down.
Rotate the brush roller by
hand to make sure the belt is
fitted properly.
5.Place the top cover
and replace the 8 screws
on the bottom
CLEAN A BRUSH ROLL JAM
IMPORTANT! DO NOT ATTEMPT TO TOUCH THE BRUSH ROLL OR CLEAR
THE BRUSH ROLL OF ANY OBSTRUCTION WITHOUT SWITCHING THE
APPLIANCE OFF AND UNPLUGGING IT FROM THE OUTLET. FAILURE TO
DO SO MAY RESULT IN PERSONAL INJURY.
1.Carefully inspect the brush roll for tangled
hair, carpet strings or large debris. Beware
of any sharp objects that may have
become lodged in the brush roll area. DO
NOT pull on anything that has jammed
tightly around the brush roll as it may
damage the unit.
2.Use scissors to carefully cut these objects off
the brush roll and remove them from the power
nozzle

Maitenane
TROUBLESHOOTING
6
3. Bearing worn out.
Problem.
Motor is not working
1. Electrical connection at hose
coupling not made.
Check the connection between the
electrified hose and the power unit.
2. Power nozzle cord not firmly
plugged into the receptacle on
the hose handle.
Plug cord firmly in
Disconnect power, remove any
object that may have blocked the
brush roller, and reset the breaker.
3. Circuit breaker tripped.
Replace belt
Disconnect power, remove any
object that may have blocked the
brush roller.
Replace the brush and bearing
assmbly by distributor.
2. The brush roller is blocked.
1. Broken or worn belt.
Brush not run
Power nozzle not
picking up well.
1. Clogged air chamber. Disconnect power, remove the
obstruction.
2. Clogged wand or hose. Disconnect power, remove the
obstruction.
Replace the brush.
3. Brush is worn out.
Possible cause Possible solution

DS1601-00000011