FOAMICO Automatic Satellite NEXT ASU 150 User manual

1 Automaic Satellit NEXT_701810-12_UK 27-08-2019
Operation Manual
Foamico Automatic cleaning.
Automatic Satellite NEXT ASU 150 (7011810)
Automatic Satellite NEXT ASU 300 (7011811)
Automatic Satellite NEXT ASU 450 (7011812)

2 Automaic Satellit NEXT_701810-12_UK 27-08-2019
Content
1. Introduction 3
1.1 Condition of liability 3
1.2 Guarantee conditions. 3
1.3 Protection against frost 3
1.4 Safekeeping 4
1.5 Declaration of conformity 4
2 Safety 4
2.1 Safety during operation of the system 4
2.2 Precautionary measures 5
2.3 Appropriate utilization 5
3 Models and symbols 6
3.1 Symbols Manuel cleaning option 6
3.2 Models. 6
3.3 Model Overview 7
4 Installation 8
4.1 Safety instructions for Mounting and Installation 8
4.2 Location and Mounting 8
4.3 Water supply 8
4.4 Electrical Supply 9
4.5 Air supply 9
4.6 Supply of Detergent and sanitizer 9
5 Operation 10
5.1 FOAMICO controller for Automatic cleaning 10
5.2 Manuel cleaning Preparation: 10
5.3 Rinsing operation 10
5.4 Foam operation 10
5.5 Spray disinfection. 10
5.6 Stop of operation 11
6 Troubleshooting / Failures 12
6.1 Troubleshooting. 12
6.2 Failures control system. 13
7 Maintenance 13
7.1 Rinsing hose. 13
7.2 Nozzles. 13
7.3 Low pressure valves / guns 13
7.4 Couplings. 13
7.5 Ball valves. 13
7.6 Non-return valves 13
7.7 Suction filter / chemical hose. 14
8 Technical data 14
9 Spare parts 15
9.1 Automatic satellite Station NEXT series 15
9.2 Front plate 1001922 18
9.3 Motor valve for foam and rinse 19
9.4 Outlet pipe with actuator valve 1002055 21
9.6 Manuel system for foam and rinse circuit part number. 1000996-1000 22
9.7 Spare parts foam and rinse block, positioning ring, injector 24
10 Electrical diagram I/O box 1001805 25
11 Flow diagram ASU 150-300-450 28
12 Name plate 30
13 Declaration of Conformity 31

3 Automaic Satellit NEXT_701810-12_UK 27-08-2019
1. Introduction
FOAMICO congratulates you with your new FOAMICO Cleaning system. FOAMICO Automatic cleaning.
series are developed to be used for professional cleaning purpose.
The system is manufactured mainly of high grad stainless steel. It is designed to meet today’s high hygiene
standards
Attention! This Manual is part of a bigger reference library. Before the Satellite is installed and set
into operation, the FOAMICO Automatic Controller direction and operation manual must be read
carefully.
1.1 Condition of liability
The responsibility for the treatment and operation in an appropriate manner rests with each individual user.
Thus it is of great importance that this manual is available to the sanitary employee at any time
1.2 Guarantee conditions.
For a period of 12 months from the date of delivery your dealer warrants for parts which don’t function due
to defects of material or production. This guarantee does not cover wearing parts (as described in the section
about spare parts). This guarantee is covering the replacement or repair of the defect part. Any dismounting,
forwarding, and mounting expenses are paid by the purchaser. The costs for any possible return from
FOAMICO after finished repairs rest with FOAMICO. The defect parts are the property of FOAMICO
Claims which might be raised for any other legal reason, or normal wear and tear, as well as damage on parts
which can be related to negligent or wrong treatment, are not covered by this guarantee.
This guarantee does not cover at all, if the system has been exposed to frost.
This guarantee becomes void if changes or repairs have been implemented by non-authorized persons. Any
claims under the guarantee will only be accepted if they are announced to
FOAMICO immediately after the damage has been observed. This guarantee becomes void as soon as the
system changes ownership.
Dealers and FOAMICO cannot be held responsible for personal injuries, damages to equipment, loss of
earning including those caused by production loss, loss of stock or the like, which might arise from
inappropriate or delayed delivery of the sold product, regardless the reason, including defects in production
or material. In addition, please read our usual terms of sale and delivery
WARNING
Due to the nature of low pressure cleaning systems Pressure surges can occur. The installer is responsible for
dimensioning the supply line to be able to adapt Pressure surge.
Dealers and FOAMICO cannot be held responsible for personal injuries, damages to equipment sounding
rooms, Water Supply line or water outlet line.
1.3 Protection against frost
The equipment should only be installed in frost free rooms.
Prior to being exposed to frost, the system must be emptied for water (frost protected). Even shorter periods
of exposure to frost can damage the equipment.

4 Automaic Satellit NEXT_701810-12_UK 27-08-2019
This symbol refers to safety and danger moments. Neglect of these instructions can cause damage on persons
and objects.
1.4 Safekeeping
You are requested to store this manual in a place where it is at your disposal at any time, and it should be
handed over to the person responsible for this product. Should the manual get lost, please don’t hesitate to
require another one from your agent.
1.5 Declaration of conformity
We FOAMICO declare that this product is in conformity with the following directives:
- Machinery (2006/42/EC)
-EMC directive 2014/30/EU
2 Safety
2.1 Safety during operation of the system
Suitable working clothes are recommended, e.g. as protection against 70°C hot water. Goggles, respirators,
and rubber gloves should always be used. The use of non-slip footwear is recommended, because due to
water and foam the floor sometimes can get slippery.
Do not connect or use detergent before having read the instructions from the Detergent supplier. Always
consult the Detergent supplier to get instructions for correct use. Wrong use of detergent can be dangerous, it
can produce poisonous gas, great chemical burns an allergic reaction.
The system should not be started up before the operator using the system, has been instructed in the correct
utilization, adjustment, and maintenance of it. Never direct the water jet towards persons. Make sure that the
couplings” lock” when the hose and nozzles are connected. Always follow this procedure before use. Always
depressurize the system after use. This is done by first closing the valve for the water supply and afterwards
opening the low-pressure valve or gun.
During operation of the system: ensure that the low-pressure gun/valve is closed, before releasing the
coupling and change the nozzle. When the low-pressure gun/nozzle is opened, the water jet will cause a
certain back pressure. Make sure to have a strong grip on the handle and a firm foothold.
The noise level from the equipment is less than 70dB (A). During rinsing, the operator is exposed to a higher
noise level. This is caused by the impact from the water jet on the surroundings. It is therefore recommended
the use ear protectors during the cleaning process
Never direct the water jet towards electrical equipment. Avoid water in electrical plugs.
Switch of the power supply, before plug in or remove a plug from an electrical socket.
Attention! Use only original FOAMICO Nozzles, hoses, couplings and spare parts.

5 Automaic Satellit NEXT_701810-12_UK 27-08-2019
2.2 Precautionary measures
The construction of the system is in accordance with the generally adopted, technical requirements and the
stipulations concerning working environment and accident prevention. Therefore the equipment must be in
its best technical state before being used, and must only be utilized according to its requirements and by
observance of the precautionary measures and operational instructions. Disturbances, which might influence
the safety in particular, must be rectified immediately.
2.3 Appropriate utilization
FOAMICO low-pressure system is manufactured with the purpose of:
Rinsing with water, spreading foam and disinfection within the stated boundaries.
Any other kind of application or use beyond this is considered to be inappropriate and deviant concerning the
requirements, and may lead to dangerous situations. FOAMICO is not liable for any sequential damages
brought about by this.
Appropriate utilization includes the following:
The instructions, regulations, and recommendations given in this manual.
The observance of the prescribed intervals for inspection and maintenance.
The correct maintenance for good operational condition of the system.
The observance of the prescribed conditions for the environment and operation.

6 Automaic Satellit NEXT_701810-12_UK 27-08-2019
3 Models and symbols
3.1 Symbols Manuel cleaning option
FOAMICO Main Stations come with a complete set of symbols. The symbols will make operation easier.
Attention! The symbols should be installed with a supervisor from the chemical supplier.
Rinsing
Foam disinfection
Foaming Foam Cleaning
(e.g. acid)
Spray disinfection Foam Cleaning
(e.g. Alkaline)
3.2 Models.
FOAMICO can supplies this FOAMICO Automatic cleaning with 5 different versions/ type of Manuel
cleaning.
Model number 1. Injector 2. Injector 3. Injector
Type-1 (1002088)
Foam Spray disinfection
Type-2 (1002089)
Foam Foam
Type-3 (1002090)
Foam Spray disinfection Spray disinfection
Type-4 (1002091)
Foam Foam Spray disinfection
Type-5 (1002092) Foam Foam Foam

7 Automaic Satellit NEXT_701810-12_UK 27-08-2019
3.3 Model Overview
Type 1 Type 2
Type 3 Type 4
Type 5

8 Automaic Satellit NEXT_701810-12_UK 27-08-2019
4 Installation
4.1 Safety instructions for Mounting and Installation
IMPORTANT!
Never install or apply damaged products. Claims concerning damages must be made to the carrier
immediately.
IMPORTANT!
Work in the connection with installations, start up, and maintenance on the FOAMICO cleaning systems
should only be done by authorized electricians, because the valid national regulations concerning prevention
of working accidents. (e.c. high voltage regulations: EN 60204, VBG4 DIN-VDE 0100/0113/0160) must be
respected. In cases of irregular installations there is a risk for major damages on both material and people.
4.2 Location and Mounting
The system should always be located in a frost-free room. Stationary system must always be mounted where
the surfaces are of solid quality, and when applicable the fastening must always be done with the delivered
bolts and raw plugs. Holes for wall brackets must be drilled according the dimensional drawing.
The Automatic Satellite NEXT should be connected to an adequate pipe system. This should correspond to
distance from the water supply, the maximum water flow and vertical distance from the boosting System.
4.3 Water supply
ATTENTION! Connection to water supply should always be done in according to local and national
standards.
If the legislation in your country requests safeguards for reverse current, this must be provide for.
WARNING
Due to the nature of low pressure cleaning systems Pressure surges can occur. The installer is responsible for
dimensioning the supply line to be able to adapt Pressure surge.
BEFORE mounting the system, the piping must be flushed with water in order to remove possible parts or
dirt.
ATTENTION. At the supply pipe to the main station a valve and filter must be installed. We recommend
using Original FOAMICO installations set.
The water should be connected to the inlet shown in POS A. fig. 5.1
AFTER mounting the system flushing of the pipes must always be done with the system in “rinsing mode”,
to avoid any impurities in the injector system. Please keep rinsing until the rinsing nozzle shows an
invariable clean water jet coming out.

9 Automaic Satellit NEXT_701810-12_UK 27-08-2019
4.4 Electrical Supply
WARNING
The user or the installer is responsible for the installation of correct Grounding and protection according to
current national and local standards. All operations must be carried out by qualified personnel.
WARNING
Never make any connections in the pump terminal box unless electric supply circuits have been switched off
for at least 5 minutes.
ATTENTION! Connection the power supply must only been made by authorised electrician’s´.
ATTENTION! The connection has to be done to a main switch installed next to the station.
Supply voltage and mains: 200-500 VAC. 2,0A. 50/60 Hz, PE.
4.5 Air supply
ATTENTION! Connection to air supply should always be done in according to local and national standards.
ATTENTION! The cleaning system shall always have its own air supply system. Failure in the cleaning
system could accidentally lead to water and/or detergent can flow back in the air system. To avoid damage
on other installations. it is mandatory to make a separate air supply system for the cleaning equipment.
BEFORE mounting the system, the piping must be cleaned with air in order to remove possible parts or dirt.
The air should be connected to the inlet shown in POS B fig. 5.1
4.6 Supply of Detergent and sanitizer
ATTENTION! The handling and connection should be done according to description from the Detergent
supplier.
ATTENTION! Always follow the safety instructions for the detergents. They should always be available
together with the detergents.
Before connection of the detergent, the concentration Nozzle must be installed.
Size mm
Concentration %
**
Size mm
Concentration %
**
0,5
1,4
0,9
3,0
0,6
1,7
1,1
3,8
0,7
2,0
1,3
4,8
0,8
2,5
1,5
6,0
** Concentration varies from detergent to detergent depending on viscosity. Above figures is based on a
detergent with a viscosity as water.
Installed the nozzle POS G. Fig. 5.1 and installed the suction hose POS G fig 5.1
Places the suction hose in the detergent container.

10 Automaic Satellit NEXT_701810-12_UK 27-08-2019
5 Operation
5.1 FOAMICO controller for Automatic cleaning
Please see separate manual for the Control system.
5.2 Manuel cleaning Preparation:
1. Connect the hose to the coupling POS. E. figure 5.1 make sure the valve is closed.
2. Make sure the low-pressure valve/ gun at the end of the hose is closed
3. Open the ball valve POS E fig.5.
The Satellite is now ready.
5.3 Rinsing operation
1. Mount the rinsing nozzle or rinsing pipe in the coupling at the low-pressure valve / gun (marked with blue
or green protection)
2. set the handle POS. D fig. 5.1 in rinse position
3. The system is now ready for rinsing. Rinse by open the low-pressure valve / gun.
4. ATTENTION! After rinsing the hose must be depressurized. Close the valve POS E fig. 5.1 and open the
low-pressure valve/gun. The hose can now be disconnected.
5.4 Foam operation
1. Mount the foam nozzle in the coupling at the low-pressure valve / gun (marked with white)
2. Set the handle POS. D fig. 5.1 in foam position.
3. Adjust the air pressure to 4-6 bar on the regulator POS H fig 5.1 (differs from detergent to detergent.
Often has to be fine-tuned during first time foaming)
4. The system is now ready to foam. Apply foam by opening the low-pressure valve/gun
5. After foaming the system must be rinsed with clean water. Place hose for detergent in a container with
clean water. Open the low-pressure valve/ gun for minimum 15 sec.
6. ATTENTION! Set the handle POS D fig 5.1, back in rinse position when Foam operation is ended.
7. ATTENTION! Before choosing another cleaning operation with another chemical, the system must be
flushed with clean water for at least 30 seconds. This is done by following the instructions in 5.2 rinsing
operation”
5.5 Spray disinfection.
1. Mount the disinfection nozzle in the coupling at the low-pressure valve / gun (marked with yellow
protection)
2. Set the handle POS. D fig. 5.1 in disinfection position
3. The system is now ready for sanitizing. Sanitize by open the low-pressure valve / gun.
4. After sanitizing the system must be rinsed with clean water. Place the hose for disinfection in a container
with clean water. Open the low-pressure valve/ gun for minimum 15 sec
5. ATTENTION! Set the handle POS D fig 5.1, back in rinse position when Foam operation is ended.
6. ATTENTION! Before choosing another cleaning operation with another chemical, the system must be
flushed with clean water for at least 30 seconds. This is done by following the instructions in 5.3 “rinsing
operation”

11 Automaic Satellit NEXT_701810-12_UK 27-08-2019
5.6 Stop of operation
1. Make sure that the injectors has been rinsed with clean water
2. ATTENTION! Set the handle POS. D fig 5.1.
3. Close the valve POS E fig. 5.1
4. Depressurize the hose by opening the low-pressure valve /gun.
5. Disconnect the hose.
FIGURE. 5.1
A. C
onnection
for
water supply
E.
Connection for hose. Rinse and foam
Manuel operation
B.
Connection for air supply
F.
Advanced control panel
C. Connection pipe
Automatic cleaning zones
G
.
connection for l
imiting nozzles. Adjust
concentrations
D.
Handle for selecting
Manuel
operation
H
. Pressure reducer for air.
Table 5.1

12 Automaic Satellit NEXT_701810-12_UK 27-08-2019
6 Troubleshooting / Failures
6.1 Troubleshooting.
Fault Cause Action
No rinsing pressure. Booster or main station not started. Start booster/or main station.
Too many users on the same time. Check maximum number of users.
The ball valve at the inlet of the system is
not opened.
Open the ball valve.
Unstable rinsing pressure. Unoriginal rinsing nozzle with too high
water consumption is used.
Change to master rinsing nozzle – observe
technical data for model.
The system does not suck up any
detergent into the injector.
Operation handle is not in position”
foam”.
Turn into position” foam”.
Limiting nozzles is to small The dosing must be adjusted. Check with
the description from the detergent
supplier. Change he nozzle
.
Limiting nozzle is blocked by chemical
remains.
Change the limiting nozzle.
Injector system is blocked by chemical
remains.
Injector system and water nozzle in the
injector must be disassembled and
cleaned.
Leakages on the detergent inlet. Air is
drawn into the detergent line
Check the chemical inlet. Change the
suction hose.
Blocked suction filter at the end of the
suction hose.
Clean or change suction filter.
Empty chemical container. Change to new chemical container.
Suction filter above fluid level in the
chemical container.
Lead the suction filter underneath the
fluid level.
No compressed air to the system. Open the air inlet to the system.
The rinsing hose is” pounding”. Chemical product mixed with water. Exchange the chemical container.
The used chemistry is not a foam
product.
Change to a foam product.
Injector system is blocked by chemical
remains.
Injector system and water nozzle in the
injector must be disassembled and
cleaned
.
Limiting nozzle is blocked by chemical
remains.
Change the limiting nozzle
Fault Cause Action
Low foam quality. No compressed air to the system. Open the air inlet to the system.
Wrong product. Change to a foam product.
Unoriginal foam nozzle is installed. Change to original 50/200 foam nozzle,
installed with white nozzle guard.
Insufficient air supply to the system. Min. 150 l/min. and max. 200 l/min. at
4-6 bars is requested.
Air pressure not set correct. Is adjusted on the air regulation valve to
be 4-6 bars.
Operation selector is not in the
position” foam”. Turn it into the position” foam”.

13 Automaic Satellit NEXT_701810-12_UK 27-08-2019
6.2 Failures control system.
Consult FOAMICO Automatic Controller direction and operation manual.
7 Maintenance
7.1 Rinsing hose.
ATTENTION! The rinsing hose should be checked for any damage or week point before taking it into use
every day. A damaged hose can potential be dangerous.
Do not drive across the hose. Be careful not to damage the hose on any sharp edged or corners.
After use clean the outside of the hose. Store it on a hose hanger.
For security reasons, it is recommended to change the hose at least once every 12 months.
7.2 Nozzles.
Nozzles are warned over time. And warned out nozzle is less effective. It can result in less rinsing power,
higher water usage, higher chemical consumption. Check the nozzles on a regular basis. 1 to 2 times every
month is recommended. Change the nozzle if they are damaged. To be sure you will get the optimized result
we recommend using FOAMICO nozzles.
7.3 Low pressure valves / guns
They must be checked regular. The nut on the handle has to tighten regularly. Check couplings, swivels,
handles for any damaged. A damaged part must be changed for security reasons.
7.4 Couplings.
Couplings should be cleaned and greased on a regularly basis. Use only approved grease. This will extend
the life time of couplings. Always make sure there is a nozzle or lance mounted in the coupling before
opening. Rinsing through an open coupling can damage the O-rings.
7.5 Ball valves.
Every ball valve on the inlet for water inlet for air outlet for water/foam and outlet for sanitizer must be
adjusted
First time, after one week, and then once every month. Tight the nut on the handle to avoid leakage
7.6 Non-return valves
ATTENTION! Non-return valves are very important to secure a correct function of the system.
Non-return valves for air: The system has 2 non- return valves for air. The purpose of these is to prevent
water running back into the air system. Due to the potential risk, the air system for the cleaning system must
be separate from other air systems.
ATTENTION! Never leave the valve for air open. Always secure it is closed when not foaming!
If leakage of water is observed anywhere in the airline, both non-return valves must be changed.
- Non-return valve for chemical: The system has one for each chemical intake. The purpose is to prevent
water running back into to chemicals. It will dilute the chemical and result in none or bad foam quality and to
low concentration
ATTENTION! Non- return valves should be checked once every week. It is recommended to change every
1-2 year. Use only Original FOAMICO non-return valves.

14 Automaic Satellit NEXT_701810-12_UK 27-08-2019
7.7 Suction filter / chemical hose.
The suction filter for chemical should be clean once every week. It is recommended to change filter and
chemical inlet hose every year.
8 Technical data
Automatic Satellite Unit ASU150 ASU300 ASU450
Water connection:
Min./max. inlet pressure bar 10/30 10/30 10/30
Max. water consumption l/min. 450 450 450
Max. Temperature °C 70 70 70
Pipe dimension inlet inch 1-1/4” 1-1/4” 1-1/4”
Pipe dimension outlet inch 1-1/4” 1-1/4” 1-1/4”
Power Supply:
Standard voltage V 1x220 or 1x220 or 1x220 or
3x 380-500 3x 380-500 3x 380-500
Frequency Hz 50/60 50/60 50/60
Nominal current A 2 2 2
Fuse A 10 10 10
Electrical connection dimension mm2 1,5 1,5 1,5
Air supply:
Pipe dimensions inlet mm 8 8 8
Air supply bar 5/10 5/10 5/10
Air consumption l/min. 150-200 300-400 450-550
Dimensions (WxHxD) mm 502x951x402
Weight kg 47
Accessories delivered with Manuel cleaning
Standard rinsing nozzle: Stainless steel Nozzle type 25/30 25/30
Standard rinsing lance: Stainless steel Nozzle type 25/30. 25/30
Standard foam nozzle type 1.Stainless steel Nozzle type 50/200 50/200
Alternative foam nozzle type 2.Stainless steel Nozzle type 65/150 65/150
Standard Sanitizer Nozzle Stainless steel Nozzle type 40/30 40/30
Extra Accessories:
Nozzles for all purposes
Lances for the challenging and complex assignment
Hoses and hose reels

15 Automaic Satellit NEXT_701810-12_UK 27-08-2019
9 Spare parts
9.1 Automatic satellite Station NEXT series
Figure 9.1 Satellite Station enclosures

16 Automaic Satellit NEXT_701810-12_UK 27-08-2019
Figure 9.1 Satellite Station overview

17 Automaic Satellit NEXT_701810-12_UK 27-08-2019
QTY. NO: Description Description1 Beschreibung
1 1000910 Cabinet Main Station Gehäuse
1000996* 3 Injector block complete Model 1 3 Injektor- Block komplett
1000997* 3 Injector block complete Model 2 3 Injektor- Block komplett
1000998* 3 Injector block complete Model 3 3 Injektor- Block komplett
1000999* 3 Injector block complete Model 4 3 Injektor- Block komplett
1 1001000* 3 Injector block complete Model 5 3 Injektor- Block komplett
1 1000134 Pressure regulator with Filter- Manometer. fittings Druckreduzierventil mit
1 1000719 Nut for union Blok part Schraube für Verschraubung
1 1000720 Union Blok part Verschraubung
1 1001234 Air inlet assembly All models Lufteinlassanordnung
1 1700074 Connector Ø8 Hose - 1/4"RG Gerade Steckkupplung AG
1 1700138 Labels Set Symbole
1 1001360 3 Injector block complete Automatic block 3 Injektor- Block komplett
2 1000718 Union for block Verschraubung
1 1001116 solenoid valve 1/4" female female Magnetventil
2 1001640 Clamp K 50,5 K 50,5 Clamp K 50,5
1 1001922 Front for Automatic Satellite Frontabdeckung
1 1000366 coupler 1" - 1 1/4" RG female - female Reduziert muffe
1 1000364 Nipple 1-1/4" 110mm Rohr 1-1/4"
1 1002055 Outlet tube Automatic main station Ausgangs Rohr
2 1000097 90-degree Elbow 1/2" RG Winkel
1 1000630 Nipple 1/2" 300mm Nippel 1/2" 25mm
2 1000077 Nipple 1/2" 40mm Nippel 1/2" 40mm
1 1000128 Top bracket for Main station Obere Halterung
1 1001853 Inlet tube Automatic Satellite Eingangs Rohr
2 1002063 Square tube 25 x 25 x 2,0mm
1 1001805 I/O box Automatic I/O box
1 1001002 Check valve 1/4" x 1/4" male - male EPDM Rückschlagventil Luft
1 1000100 Air connection for hose Ø 6 mm – ¼" - Female Gerade Steckkupplung Ø 6 mm – ¼" IG
1 1002060 Bracket for Control box Automatic satellite Winkelträger
2 1001795 Hex Bolt ISO 4017 - M6 x 10- Schraube
Table 9.1 Satellite Station spare parts.

18 Automaic Satellit NEXT_701810-12_UK 27-08-2019
9.2 Front plate 1001922
Figure 9.1 Satellite Station Front overview
QTY. NO: Description Description1 Beschreibung
1 1001921 Front plate Automatic Satellite Frontabdeckung
1 1000335 Handel Ø10 - 96mm Griff
2 1000353 Button Head Screw ISO 7380 - M4 x 8 --- 8N Schraube
1 1001739 HMI Modul HMI - Interface
1 1001807 Bracket f. HMI module Automatic system Halter für HMI - Interface
8 1002084 Screws f Thermp plast M3,5 x14 mm Screws f Thermp plast
Table 9.2 Satellite Station Front spare parts.

19 Automaic Satellit NEXT_701810-12_UK 27-08-2019
9.3 Motor valve for foam and rinse
1001360-150L/min. 1002176-300L/min. 1002177-450L/min.
Figure 9.1 Motor valve overview

20 Automaic Satellit NEXT_701810-12_UK 27-08-2019
QTY. NO: Description Description1 Beschreibung
4 1000990 Ball gasket for for 3 injector system Kugeldichtung
1 1000988 Main part for 3 injector system Hauptteil für
1 1001368 Ball / shaft for Automatic block Kugle - Welle für
4 1000993 Plug and holder for Ball gasket Stopfen und Halter für
1 1000533 Bearing for shaft 3 injector system Lager für Welle
1 1000534 Pressure ring for 3 Injector system Druckring für
2 1000576 O-Ring Ø11,0 x 1,78 O-Ring
1 1000538 O-Ring Ø69 x 1,78 O- Ring
2 1000540 Ø1,8 Injector for 3 Injector system Ø1,8 Injektor für
4 1000926 Socket Head Cap Screw EN ISO 4762 M6 x 40 - 24N Innen-Sechskantschraube
3 1000790 Check valve 1/4" male x ø6 hose Hi Flour Rückschlagventil Chemie
1 1001002 Check valve 1/4" x 1/4" male - male EPDM Rückschlagventil Luft
1 1000100 Air connection for hose Ø 6 mm – ¼" - Female Gerade Steckkupplung Ø 6 mm – ¼" IG
1 1001064 O-Ring Ø31.47 x 1,78 O- Ring
1 1001926 Motor Automatic block Motor
2 1000480 Washer ISO 7093 - 5 Washer ISO 7093 - 5 Unterlegscheibe
1 1001367 O-Ring 22,0 x2,4 O-Ring
1 1001364 Outlet pluck Automatic block Ausgangs Part
2 1001366 Ball gasket for Automatic system Kugeldichtung
1 1001362 Bottom part for Automatic Block Bodenteil für
1 1001371 Motor bracket for Automatic block Motor Halter
4 1001927 Proximity sensors NO/NC Annäherungssensor
1 1001361 Coupling Motor -Block Automatic Kupplung Motor -Block
1 1001514 Connection shaft for Automatic block tysk tekst
1 1001363 Ball / shaft for Automatic Block Kugle - Welle für
1 1001641 Seal 38mm Tri Clamp EPDM Seal Seal
4 1000495 Washer Washer DIN 125 - A 6.4 Unterlegscheibe
2 1001944 Hex Bolt ISO 4017 - M5 x 6-N Schraube
1 1001749 Socket Set Screw ISO 4029 - M4 x 4-N Inbusschraube
2 1002085 Socket Head cap screw EN ISO 4762 M4 x 5 -5N Innen-Sechskantschraube
Table 9.3 Motor valve spare parts.