Skyworth SLTV-1963A User manual

SLTV-1963A
SLTV-2063A
19 /20 LCD Television / Monitor
Owner s Manual

RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lighting flash with arrow head within a
triangle is intended to tell the user that parts
inside the product are a risk of electric shock
to persons.
The exclamation point within a triangle is
intended to tell the user that important
operating and servicing instructions are in
the papers with the appliance.
WARNING: To reduce the risk of electric shock do not expose this apparatus to rain or moisture and objects
filled with liquids, such as vases, should not be placed on this apparatus.
IMPORTANT SAFETY INSTRUCTIONS
1.READ INSTRUCTIONS - All the safety and operating
instructions should be read before the unit is operated.
2.RETAIN INSTRUCTIONS - The safety and operating
instructions should be retained for future reference.
3.HEED WARNINGS - All warnings on the unit and in
the operating instructions should be adhered to.
4.FOLLOW INSTRUCTIONS - All operating and use
instructions should be followed.
5.CLEANING - Unplug this unit from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning the exterior
cabinet only.
6.ATTACHMENTS - The manufacturer of this unit
does not make any recommendations for attachments,
as they may cause hazards.
7.WATER AND MOISTURE - Do not use this unit near
water. For example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a
swimming pool.
8.ACCESSORIES - Do not place this unit on an
unstable cart, stand, tripod, bracket, or table.
The unit may fall, causing serious injury, and serious
damage to the unit. An appliance and cart
combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
TV/CATV MODE SELECTION
When shipped from the factory, the TV/CATV menu option is set to the TV mode. If using CATV, set the
menu option to CATV (Cable Television)
PORTABLE CART WARNING
9.VENTILATION - Slots and openings in the cabinet
back or bottom are provided for ventilation, to
ensure reliable operation of the unit and to protect it
from overheating. These openings should never be
blocked by placing the unit on a bed, sofa, rug, or
other similar surface. This unit should never be
placed near or over a radiator or heat source. This
unit should not be placed in a built-in installation,
such as a bookcase, or rack unless proper ventilation
is provided or the manufacture s instructions have
been adhered to.
10.POWER SOURCE - This unit should be operated
only from the type of power source indicated on the
rating plate. If you are not sure of the type of power
supply to your home, consult your appliance dealer
or local power company. For units intended to
operate from battery power, or other sources, refer
to the operating instructions.
,
CAUTION
Changes or modifications not expressly approved by the party responsible for compliance with the FCC
Rules could void the use s authority to operate this equipment.
,
1
S3126A
WARNING:
WARNING:Do not leave any stationary images, patterns, PIP box, or letterbox images on the screen foran extended
period oftime. Also, do not display the same stationary patterns frequently. This may result in permanent
ghost images on the display unit. This type of damage is not covered under warranty. Examples of this
type ofsituation can be but not limited to the following: side bar images, stock market report bars, video
game patterns, closed captioning, shopping channel logo, pricedisplay, and letterbox black bars. To
prevent thistype of damage, display constant moving images that fill the screen as often as possible.
According to theindustrial standards, there are a certainnumber of defective pixels both bright
and dark that are acceptable. Although we produce panel with more than 99.99 percent active
cells, there stillmay be some cells that donot produce light or remain lit. For more information,
please contact salesor the technical support.

11.POLARIZATION - This unit is equipped with a
polarized alternating current line plug (a plug
having one blade wider than the other). This plug
will fit into the power outlet only one way. This is
a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If
the plug still fails to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose ofthe polarized plug.
12.POWER-CORD PROTECTION - Power supply
cords should be routed so that they are not likely
to be walked on or pinched by items placed upon
or against them, paying particular attention to
cords at plugs, convenience receptacles, and the
point where theyexit from the appliance.
13.LIGHTNING - To protect your unit during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the unit
due to lightningand power line surges.
14. POWER LINES - An outside antenna system
should not be located in the vicinity of overhead
power lines, or other electric light or power
circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna
system, extreme care should be taken to keep
from touching such power lines or circuits as
contact with them might be fatal.
15.OVERLOADING - Do not overload wall outlets
and extension cords as this can result in a risk of
fire or electric shock.
16.OBJECT AND LIQUID ENTRY - Do not push
objects through any openings in this unit as they
may touch dangerous voltage points or short out
parts that could result in fire or electric shock.
Never spill orspray any type of liquid intothe unit.
17.OUTDOOR ANTENNA GROUNDING - If an
outside antenna or cable system is connected to
the unit, be sure the antenna or cable system is
grounded to provide some protection against
voltage surges and built-up static charges.
Section 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with respect
to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and
requirements for thegrounding electrode.
18.SERVICING - Do not attempt to service this
unit yourself as opening or removing covers may
expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
19.DAMAGE REQUIRING SERVICE- Unplug this
unit from thewall outlet andrefer servicing to
qualified service personnelunder the following
conditions:
A. When the power-supply cord or plugis
damaged.
B. If liquidhas been spilled,or objects have fallen
into the unit.
C. If theunit has beenexposed to rain or water.
D. If the unit does not operate normally by
following the operatinginstructions. Adjust
only those controlsthat are coveredby the
operating instructions, asan improper
adjustment of other controls may result in
damage and will often require extensive work
by a qualifiedtechnician to restorethe unit to
Its normal operation.
E. If theunit has beendropped or the cabinet has
been damaged.
F. When the unit exhibits a distinct change in
performance, this indicatesa need forservice.
20.REPLACEMENT PARTS- When replacement
parts are required, be sure the service technician
uses replacement parts specified by the
manufacturer or those that have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or
other hazards.
21.SAFETY CHECK - Upon completion of any
service or repairs to this unit, ask the service
technician to perform safety checks to determine
that the unitis in proper operating condition.
22.HEAT - The product should be situated away
from heat sources such as radiators, heat
registers, stoves, or other products(including
amplifiers) that produceheat.
23.NOTE TO CATV SYSTEM INSTALLER - This
reminder is provided to call the CATV system
installer s attention to Article 820-40 of the NEC
that provides guidelines for proper grounding and,
In particular, specifies that the cable ground shall
be connected to the grounding system of the
building, as close to the point of cable entry as
practical.
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
ANTENNA LEAD
IN WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC - NATIONAL ELECTRIC CODE
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE S2898A
2
,

TABLE OF CONTENTS
Table of Contents
Congratulations
Specifications
Installation
Television Location
Power Source
Combination VHF/UHF Antenna
Remote Control Battery Installation
Optional Equipment Connections
Rear Panel Connectors
Front Control Panel
Function Menu Operation
PICTURE
V-CHIP
Setup menu
DTV Setting menu
PC Setup menu
Service Tips
4
4
5
5
5
5
6
7
7
7
Remote Control Operation 8-11
12-16
12
12
13
14
15
3
Special Message
17
16
Limited Warranty 18-19
TV mode 8-11
Tune menu 14

¼ò ½é¼ò ½é
Congratulations
Your new TV Monitor/Receiver features a solid state chassis that is designed to give you many years of enjoyment.
It was thoroughly tested and tuned at the factory for best performance.
CONGRATULATIONS
4
Note:
Specification are subject to change without prior notice.
NTSC/ATSC
; ATSC
(For ATV Only)
< 3W
DTV Build-in yes
19
20 20 Color (Diagonal)
433.61 x 249.41 mm (H x V)
1366 x 768
16:9
600:1
160 140
19 Color (Diagonal)
408.24 x 255.15mm (H x V)
1440 x 900
21-7/16 7-1/16 16-1/4
24-1/4 9-7/16 18-1/2
20-1/4
14-5/16

INSTALLATION
Installation
Television Location
Follow these recommendations before deciding the
location of your television.
Avoid excessive sunlight or bright lights,
including reflections.
Keep away from excessive heat or moisture.
Inadequate ventilation may cause internal
component failure.
Fluorescent lighting may reduce remote
control transmitting range.
Keep away from magnetic equipment,
including motors, fans and external speakers.
WARNING: Use this television receiver only with the
cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart
is used, use caution when moving the Cart / apparatus
combination to avoid injury from tip-over. In order to
avoid injury to children, never place your television
receiver on a piece of furniture that is capable of being
tilted by a child leaning on it, pulling on it, standing o it,
or climbing on it. A falling television can cause serious
injury or even death.
Remote Control Battery Installation
Requires two AAA batteries(supplied).
Procedure
1. Turn the remote control face down. Remove battery
cover by pressing down on the marking on the
cover and sliding it off in the direction indicated.
2. Install batteries matching(+) and(-) polarity signs.
3. Replace the battery cover by sliding in reverse until
the lock snaps.
Note: Incorrect installation can cause battery leakage
and corrosion that will damage the Remote
control.
Precautions
Replace batteries in pair.
Do not mix battery types(zinc carbon with
alkaline).
Do not recharge, heat, short-circuit,
disassemble, or burn batteries.
POWER SOURCE
TO USE AC POWER SOURCE
Use the AC /DV adaptor provided for operation on AC.
Insert the AC cord plug into a standard 110-120V 60HZ
polarized AC outlet.
AC outlet
Wider Hole
and Blade
Polarized AC CordPlug (One
blade is widerthan the other)
5
To use Car cord
Use the Car Cord provided for operation on 12V DC.
NOTE:
1.AC/ DC adaptor provided can be connected to
the specified voltage (AC 110 volts 60HZ).
2.If the polarized AC cord does not fit into a non-
polarized AC outlet, do not attempt to file or cut
the blade. It is the user s responsibility to have
an electrician replace the obsolete outlet.
3.If you cause a static discharge when touching
the unit, and the unit fails to function, simply
unplug the unit from the AC outlet, wait a few
minutes, and plug it back in. The unit should
return to normal operation.
,

INSTALLATION
Combination VHF/UHF Antenna
Combination VHF/UHF Antenna (Single 75 ohm
cable or 300 ohm twin-lead wire)
Connect the 75 ohm cable from a combination
VHF/UHF antenna to theantenna jack.
Combination VHF/UHF Antenna (Separate VHF and
UHF 300 ohm twin-lead)
Connect the UHF twin-lead wire to a combiner (not
supplied). Connect the VHF twin-lead to the 300-75
ohm matching transformer (not supplied). Attach the
transformer to the combiner. Attach the combiner to
the antenna jack.
Separate VHF/UHF Antenna
Connect the 75 ohm cable from the VHF antenna and
the UHF antenna twin-lead to a combiner (not
supplied). Attach the combinerto the antenna jack.
NOTE: If your VHF antenna has a twin-lead wire, use
the 300-75 ohm matching transformer( not supplied),
then connect the transformer to the combiner.
For Subscribers to Scrambled Cable TV service
If you subscribe to a cable service which requires the
use of a converter/descrambler box, connect the
incoming cable to the converter/descrambler box and
connect the output of the box to the antenna jack on
the back of the television. Follow the connections
shown left. Set the television to the output of the
converter/descrambler box (usually channel 3 or 4)
and use the converter / descrambler box to select
channels.
For Subscribers to Unscrambled Basic Cable with
Scrambled Premium Channels
If you subscribe to a cable service in which basic
cable channels are unscrambled and premium
channels require the use of a converter/descrambler
box, you may wish to use a two-set signal splitter (
sometimes called a two-set coupler )and an A/B
switch box from the cable installer or an electronics
supply store. Follow the connections shown left. With
the switch in the B position, you can directly tune
any nonscrambled channels on your TV. With the
switch in the A position, tune your TV to the output
of the converter/descrambler box (usually channel 3
or 4) and use the box to tune scrambled channels.
6
Combination VHF/UHF Antenna
Single 75 ohm cable
300 ohm twin-lead wire
Splitter
Take off the Splitter
300-75 OHM MATCHING
TRANSFORMER
(not supplied)
UHF Antenna
300 ohm twin-lead wire
VHF Antenna
Single 75 ohm cable
300 ohm twin-lead wire
300-75 OHM MATCHING
TRANSFORMER
(not supplied)
COMBINER
(not supplied)
Incoming CATV
Converter/Descrambler
Converter/Descrambler
Splitter A/B Switch A B
This television has an extended tuning range and can tune
most cable channels without using a cable company
supplied converter box. Some cable companies offer
premium pay channels in which the signal is scrambled.
Descrambling these signals for normal viewing requires the
use of a descrambler device which is generally provided by
the cable company.
For Subscribers to Basic Cable TV Service
For basic cable service not requiring a converter/
descrambler box, connect the CATV 75 ohm coaxial
cable directly to the antenna jack on the back of the
television.

BASIC CONTROLS AND CONNECTIONS
Optional Equipment Connections
Procedure
Connect equipment as shown to Audio/Video
input jacks.
Select the Video mode by pressing TV/AV button.
Operate optional equipment as instructed in
equipment manual.
Front Control Panel
The front control panel can be used to access
menus and switch video mode when the remote control
is not available.
Note: The ON/OFF indicator LED(red) will light up
when you insert the AC cord into the AC outlet.
7
Headphone jack: Plug an earphone or monaural
headphones into this jack for private listening.
Side Panel Connectors
1. Antenna or cable In
2. Video / S-Video Audio Right In
3. Video / S-Video Audio Left In
4. Video In
5. S-Video In
6. Component In
7. Component / PC Audio Right In
8. Component / PC Audio Left In
9. PC In
10. Headphone Jack
11.Audio Right Out
12.Audio Left Out
ANT INANT IN PC INPC IN HEADPHONEHEADPHONE
RRLL
VIDEOVIDEO S-VIDEOS-VIDEO
YYPbPb PrPr
DC 12VDC 12V
COMPONENTCOMPONENT
AUDIO IN 1AUDIO IN 1
RRLL
AUDIO IN 2AUDIO IN 2
1 2 34567910
1
8
1. VOL.- Button
2. VOL.+ Button
3. CH.- Button
4. CH.+ Button
5. Menu Button
6. TV/AV Button
7. Power Button
8. Power Indicator / Remote Sensor
Rear Panel Connectors
1. DC 12V In
112288
4455773366
RRLL
AUDIO OUTAUDIO OUT
11 12

»ù±¾²Ù×÷»ù±¾²Ù×÷
REMOTE CONTROL OPERATION
Remote Control Operation
Turn on / off.
POWER
Mute the sound.
Switch to desired input source.
Back to previous viewed channel.
8
MUTE
P.M
I/II
P.M
AUDIO
I/II
CC
CC
TV/AV
TV/AV
Select channel or enter password.
1
2
3
4
5
6
7
8
9
0
-/--
Q.VIEW
-/---/--
Q.VIEWQ.VIEW
Set the sleep timer.
SLEEPSLEEP
Display information of current input.
MENU
Display menu function.
Channels Up / Down.
CH+
CH-
Volume Up / Down
VOL-
VOL+
Select desired picture mode.
Select sound mode.
Enter CC setting menu.
Select channel digits.
DTV
DTV
Enter DTV Setting menu
2
456
8
79
- /- -
MENU
CH.-
VOL.+VOL.-
0
3
CH.+
CC
Q.
VIEW
TV/AV
I/II
P.M. DTV

REMOTE CONTROL OPERATION
1.POWER Button( )
Press this button to turn the TV on or off.
9
2. Mute Button( )
Press once tomute the sound, press again to recover
previously set sound level.
This button willnot work if CC display isswitched on.
3. Picture Mode Button( P.M )
Press this buttonto select desired picture mode. Four
picture modes areavailable including Custom, Rich,
Standard and Softmode.
4. Sound Mode Button( I/II )
When stereo programis received, press this button to
switch sound systembetween mono and stereo. When
sap program is received, press this button to switch
sound system betweenmono and sap. When stereo
and sap programis received, press this button to
switch among mono, sap and stereo.
CUSTOM RICH
SOFT STANDARD
5. Closed Captioning Button(CC )
Press this button to enter CC setting menu for analog
input which is shown above if any source except for
DTV is watched. In this menu you can switch on and off
the CC displayand select desiredCC mode including
CC1, CC2, CC3,CC4, Text1, Text2,Text3 and Text4
mode. CC modecan be set only when CC display is
switched on.
TV MODE:
CC Status On
CC Mode Text4
DTV:Press this buttonto enter DTV setting menu.
Press this buttonto enter CC setting menu for DTV
(ATSC) if DTVis watched. In this menu DTV CC
service and preferencecan be set.
Note:
Only the DTV CC serviceavailabce from the DTV
broadcasting can be selected.If there is no signal for
DTV CC serviceitem is not selectable.
DTV CC Setup menu
CLOSED CAPTION PREFERENCE
CLOSED CAPTION
CLOSED CAPTION SERVICE
1
9
14
7
8
5
6
13
12
2
456
8
79
- /- -
MENU
CH.-
VOL.+VOL.-
0
3
CH.+
CC
Q.
VIEW
TV/AV
I/II
P.M. DTV
2
34
10
11
15

REMOTE CONTROL OPERATION
6.TV/AV Button( TV/AV )
10
Press this button to select the desired input source
among TV, DTV,Video,S-Video, Componentand
PC. You canpress this button to switch among all
available inputs inthis menu continuouslyuntil desired
input is displayed.Selected input willbe switched to
automatically after two seconds.
7.Number (0-9) Button
Press these buttonsto enter digits.
These buttons fordirect access touse a channel to enter
channel number forboth ATV andDTV or enter
password for V-Chip.
8.Digit Button ( )
For ATV, press this button to select one-digit, two-digit
and three-digit channelaccess.
For example, selectingchannel 8, youcan press 8in "-" mode,
press 08 in"--"mode, press 008in"---" mode.
It can switchchannel digit according to user inputs
automatically. For example, current setting is three-digit
option. If two numbers are entered and switch to this
channel, two-digit option is setautomatically.
If an invalidchannel number is entered, it willkeep
displaying current channel.
9.Quick View Button (Q.VIEW )
Press this buttonto watch the previously viewed channel
for both ATVand DTV.
10.Sleep Timer Button ( )
Press this buttonto set sleep time.
You can adjustsleep time (in minutes) by pressing the
VOL+/- buttons in the order shown below:
0 10 20 30-----------------120
For DTV, Pressingthis button completes physical
number input for channel number and a dot will be
displayed.
To quit this menu please press CCbutton again or
MENU button orit will disappear automatically after
10-second display.
1
9
14
7
8
5
6
13
12
2
456
8
79
- /- -
MENU
CH.-
VOL.+VOL.-
0
3
CH.+
CC
Q.
VIEW
TV/AV
I/II
P.M. DTV
2
34
10
11
15

REMOTE CONTROL OPERATION
11.Recall Button( )
11
Press this buttonto display information on current input.
12.Menu Button
Press this button to enter Picture menu or quit from
current menu.
13.Channel Up(CH.+) / Down( CH.-) Button
Press these buttons to select channels in ascending or
descending order for both ATV and DTV or select
available items ina menu.
14.Volume Up(VOL.+) / Down(VOL.-) Button
Press these buttonsto increase or decrease volume,
and also toadjust the settings such as
brightness in thePicture menu, Lock On/Off in the
V-chip menu, etc.Volume Increase£¨VOL.+£©button is
also used toconfirm your selection or enter nextmenu.
15.DTV Setting MenuButton(DTV)
Press this buttonto enter .DTV Setting menu
1
9
14
7
8
5
6
13
12
2
456
8
79
- /- -
MENU
CH.-
VOL.+VOL.-
0
3
CH.+
CC
Q.
VIEW
TV/AV
I/II
P.M. DTV
2
34
10
11
15

12
Function Menu Operation
Function Menu Operation
Press MENU buttonto display Picture menu. You can
browse Picture, V-Chip,Setup, Tune and PC Setup
menu by pressingVOL+/VOL- buttons. Press CH-
button to enterthe selected menu and adjust
available settings bypressing VOL+/VOL- buttons
or confirm youselection or enter next menu by
pressing VOL+ button.
Picture menu
In Picture menu,you can press CH+/CH- buttons to
select available itemsand adjust brightness,
contrast, hue, colorand sharpness by pressing
VOL+/VOL- buttons.
Note:
Hue is only available for NTSC system.
Both Hue and Sharpness settings are not
available for PCinput.
V-Chip menu
You can set parameters on V-Chip
(parental control) inthis menu. All settings are
effective for bothATV and DTV.
The default V-ChipPassword is set as 1111.
Press CH- button to enter V-Chip menu if there is
no password orenter Password Check menu
After input password which consistsof only
digitals and spaces,press VOL+ button to
confirm. If thepassword is correct, return to
V-Chip menu. OtherwiseCheck Password menu
keep displayed andallow you to re-enter the
password. Press MENUbutton to quit from this
menu forcedly.
Lock
Press VOL+ /VOL- buttons to select On which
switches on V-Chip function or Off which
switches off V-Chipfunction.If switch off V-Chip
function, video and audio will not be blocked.
Change Password
Press VOL+ buttonto enter Password Change
menu to re-set V-Chip password.
After enter new password which consists of only
digitals and spaces, press VOL+ to confirm.
Enter the newpassword again thenpress
VOL+ button to confirm again. If the same
password is entered twice, Successful will be
displayed to indicatethat you havechanged
the password successfully.If the passwords are
different, Unmatched isdisplayed to indicate
that new passwordis invalid and allow you to
re-enter the new password. Press MENU button
to return toV-Chip menu.
TV Rating
Press VOL+ buttonto enter TV Rating menu
In this menuyou can set TV rating. Press
CH+/CH- and VOL+ /VOL- buttons to select
desired rating, blockor unblock the selected
rating. B means block and V means view.
MENU
CH.-
VOL.+VOL.-
CH.+

13
Function Menu Operation
Function Menu Operation
Input your password, press VOL+ to confirm.
If the password is correct,image and volume will
recover. Otherwise image and volume will still
be blocked andabove dialog willnot disappear.
Setup menu
You can changesome basic settings of the TVset
in this menu.Press CH- to enter this menu.
Press CH+/CH- buttons to select available items
in this menuand perform corresponding operation.
OSD Language
Multi-Language OSD aresupported by this TV set.
You can select desired OSD language by
pressing VOL+/VOL- buttons.
Factory Reset
Select this item, press VOL+to start Factory
Reset function. Ittakes a few seconds to recover
back almost all settings with default value except
for the DTVsettings.
You can try this function whenever there is
something wrong with the TV set and you can not
fix it.
MPAA Rating
Press VOL+ buttonto enter MPAA Rating menu
In this menuyou can set MPAA rating. Press
CH+/CH- buttons to select desired rating, block
or unblock theselected rating by pressing
CH+/CH- buttons.
Canada English Rating
Press VOL+ buttonto enter Canada English rating
menu when CAEng Rating item is selected
In this menuyou can set Canada English rating.
Press CH+/CH- buttonsto select desired rating,
block or unblockthe selected rating by pressing
VOL+ /VOL- buttons.
Canada French Rating
Press VOL+ buttonto enter Canada French rating
menu when CAFr Rating item is selected
In this menuyou can set Canada French rating.
Press CH+/CH- buttonsto select desired rating,
block or unblockthe selected rating by pressing
VOL+ /VOL- buttons.
OSD HPos and OSD VPos
You can adjustthe position of the main menu
includes Picture menu,V-Chip menu etc. Adjust
the position ofmain menu horizontally through
OSD HPos item and adjust the position of main
menu vertically throughOSD VPos item.
V-Chip Block
If the programis set to be blocked, black screen
will be displayed and volume is muted.
Following dialog indicatesV-Chip works and
allows adults to enter password.
DTV Setting
Select this item and press VOL+ toenter DTV
setting menu.
Aspect
This function works for all available sources. Select
display aspect ratio between 16:10 and 4:3 mode
by pressing VOL+/VOL-buttons.

14
Function Menu Operation
DTV related functionscan be reached in this menu.
Antenna level
Press VOL+ buttonto enter DTV Antenna level
menu.
This menu assistsyou to adjust the position and
direction of the antenna so that best signal can be
received. Adjust theantenna until the received
signal strength levelis 60 or higher.
Audio Setting
Press VOL+ buttonto enter DTV Andio Setting
menu.
Digital audio parameterscan be set in this menu.
Antenna level menu
Audio Setting menu
Audio Service
Press VOL+ buttonto enter Audio Service menu in
which you canselect preferred audio service. Totally
six digital audioservices are possibly available to
be selected. Whileactually selectable audio services
depend on whatkind of audio service is contained
in current program.
Audio preference
Press VOL+ buttonto enter Audio Preference menu
in which youcan select preferred audio language.
Three kinds ofaudio language are selectable
including English, Spanishand French. While one
kind of language can not be chosen as primary
language and secondarylanguage at the same time.
CC Setting
Press VOL+ buttonto enter DTV CC Setting menu.
Factory Reset
Press VOL+ buttonto reset DTV settings with
default value.
Note:
It is strongly recommended that you should scan
DTV programs right after reset DTV settings.
Otherwise you can not watch all DTV programs.
Aspect
Only DTV displayaspect ratio canbe selected
between model andmode2 using thisitem. Please
choose preferred one.
Auto Scan
Press VOL+ buttonto start DTVauto scan. It takes
a few minutes.During the autoscan process
please do notterminate it byturning off the TV set.
Otherwise the programinformation may notbe
stored.
You can modifysettings on TV input in thismenu.
All settings in this menu are effective for ATV only.
Press CH+/CH- buttons to select available items
in this menuand perform corresponding operation.
Tune menu
DTV Setting menu
Note:
You can enterthis menu only in TV mode.
Color System
Three color systems including NTSC, PAL_M and
PAL_N are supported by this TV set. You can
select AUTO to allow the TV set to detect and set
color system automatically or force the TV set to
display the chosen color system by pressing
VOL+ /VOL- buttons when this item is highlighted.
Once AUTO is selected, system will detect the
color system and force to display according to the
detection result and this item will show which
color system is forced by system while it takes a
little time to finish the automatic detection. Due
to the complicated situation it is not guaranteed
that color system can be detected correctly by the
TV set. Please select proper color system if necessary.
Function Menu Operation
ANTENNA SETUP-DIGITAL
CHANNEL STRENGTH
Adjust the antenna until
the level is 60 or hige
Signal strength
Current Max
SIGNAL STRENGTH
50 50
AUDIO SERVICE
English Stereo Main complete

15
Function Menu Operation
Skip
Press VOL+/VOL- buttons to switch on or switch
off the skipfunction. If skip function is on,you can
not watch thecorresponding program by pressing
CH+/CH- buttons. While you can watch this
program by entering the channel number directly.
Fine Tune
Try this function if TV image is not good.
The adjustable frequency range is + 625KHz.
Note:
AFT(Automatic frequency tune) function is also
available. TV set will adjust the frequency of
TV signal automatically to obtain the best effect
unless you adjustfrequency through Fine Tune
function manually.
Auto Scan
Press VOL+ buttonto search and store all
available programs automatically.
Note:
TV set will store programs of cable and antenna
systems separately. Connect cable to your TV set,
switch to cable system through TV Source item.
Available programs will be stored through channel
No.1 to channel No. 125. Then Connect antenna to
your TV set, switch to antenna system through
TV Source item. Available programs will be stored
through channel No.2 to channel No. 69.
TV Source
Press VOL+ buttonto enter TV Source menu.
In TV Source menu, you can switch TV source
among Antenna, Cable(STD),Cable(IRC) and
Cable(HRC) by pressingVOL+ button.
Please make it sure that proper TV Source is
selected before auto scan is started otherwise
programs may notbe found and stored.
PC Setup menu
You can modifysettings on PC input in thismenu
Press CH+/CH- buttons to select available items
in this menuand perform corresponding operation.
Note:
You can enterthis menu only in PC input and
there is validsignal for the PC input.
Auto Adjust
Press VOL+ buttonto start adjust PC settings
automatically. It will take a few seconds to finish
the adjustment includinghorizontal and vertical
position, phase and clock ofthe PC image. If you
are not satisfiedwith the effect, you can adjust
these settings manuallythrough following
functions
HPos and VPos
Adjust the positionof the PC image through these
items by pressingVOL+/VOL- buttons. Adjust
the position ofPC image horizontally through
HPos item and adjustthe position of PC image
vertically through VPos item.
Phase
Adjust the phaseof the PC image by pressing
VOL+/VOL- buttons. Itwill make the image
sharp or blurry
Clock
Adjust the clockof the PC image by pressing
VOL+/VOL- buttons. It will change the width of
the active imageof the PC input.
Note:
Supported PC inputformat includes:
Function Menu Operation
SVGA
MODE
640X480 60Hz
VGA
XGA
Resolution Vertical
Frequency
800X600
1024X768
60Hz
60Hz
Other formats maybe supported by the TV set.

16
Function Menu Operation
Function Menu Operation
Image Shrink
This message indicatessystem is shrinkingthe
input signal soas it canbe displayed although
part of theimage will belost. For some input
formats which cannot be displayednormally due
to the limitationof the panelor microchips used
by the TV set, software system will automatically
calculate and delete part of the image and allow
primary part ofthe image to be displayed.
Note:
Sometimes for somesupported input format,
system will alsoautomatically calculate and decide
whether or notshould shrink theinput image.
During this process, Image Shrinking message is
also displayed. Whileif system findsthat input
format should be supported by the TV set, this
message will disappearand the wholepicture
will be displayed.
Special Message:
No Signal
This message indicates there is no signal for
PC input.
If there isno signal for PC input, black screen
will be displayed and above dialog mentions you
to plug PC signal. For all inputs other than PC
input, blue screenwill be displayed if there isno
valid input.
Out Of Range
Because of the limitation of the LCD panel, some
picture format cannot be displayed normally.
This message indicates that current input exceeds
the display ability of the panel.
Invalid Mode
Due to thelimitation of microchips used by the
TV set, somepicture format can not be supported
by the TV set. This message indicates that the TV
set can notperform normal image management
for current inputformat.
Note:
For TV input, only NTSC system is supported.
For Component input, following formats are
supported. 480i@60Hz, 480p@60Hz, 576i@50Hz,
576p@50Hz, 720p@50Hz, 720p@60Hz, 1080i@50Hz,
1080i@60Hz
Auto Configuration
This message indicates that PC automatic
configuration is in process.
After finish PC image adjustment, this
message will disappear.

»ù±¾²Ù×÷»ù±¾²Ù×÷
Service Tips
Service Tips
17
Please make these simple checks as
indicated ( ) on the chart for the
respective symptoms and their possible
remedies.
No picture, no sound
Poor sound, picture OK
Poor picture, sound OK
Weak picture
Blurred picture
Double image
Lines in picture
Distorted picture
Weak reception on some channels
Horizontal bars
Picture rolls vertically
Poor colour
No colour
Misoperation of Remote control
Remote control unit no operation
On Screen Display Control outside the screen
Try differentchannel, if OK,probablystation trouble
Check aerial connections on backof set
Check aerial for broken wires
Re-orientaerial (if indoor type)
Probably local interference, such asanappliance
Adjustfine tuningcontrol
Adjust brightnesscontrol
Adjust contrast control
Check if station is broadcasting colour
Adjustcolourcontrol
Check ifsystem is correctly set
Checkifon/offswitch is "on"
Check batteriesin remotecontrol unit
Possible Remedies
Symptoms

18

19
Skyworth Electronics Inc.
1312 John Reed Court,
City of Industry, CA91745
Phone: 626-336-3698
Fax: 626-336-3238
Email: service@skyworth.com.hk
Http: www.skyworth.com.hk
Skyworth Electronics Inc.
1312 John Reed Court,
City of Industry, CA91745
Phone: 626-336-3698
Fax: 626-336-3238
Email: service@skyworth.com.hk
Http: www.skyworth.com.hk
This manual suits for next models
4
Table of contents
Other Skyworth LCD TV manuals

Skyworth
Skyworth LCD-42L29-FHD User manual

Skyworth
Skyworth LCD-26L16 User manual

Skyworth
Skyworth 39e36 User manual

Skyworth
Skyworth SLTV-1963A-1 User manual

Skyworth
Skyworth SLTV-1551A-1 User manual

Skyworth
Skyworth LCD-32L16 User manual

Skyworth
Skyworth 19E57 User manual

Skyworth
Skyworth LCD-32L29 User manual

Skyworth
Skyworth SLTV-2268A-2 User manual

Skyworth
Skyworth SKYWORTH SLTV-32L29A-2 User manual