Slinex ML-20HD User manual

ML-20HD
Video outdoor
station
Design. Uniqueness. Innovations
Design. Uniqueness. Innovations
Technical support
AHD 1080P
(2 Mp)
Thank you for
choosing our equipment User manual

ML-20HD
1REV. 2.0 2
Safety instructions
Read and keep that manual.
The device installation process should be carried out by the qulied
specialists.
Use the device from the –40 ˚C to +50 ˚C, always keep it within that
temperature range.
Installation surface should be free from vibration and impact inuence.
Keep this device far from open sources of heat, such as radiators, heaters, and
ovens.
The device can be installed near other electronic equipment in case if the
temperature of the environment does not exceed previously mentioned
range.
The device should be protected from the direct inuence of the natural
phenomena, such as direct sunlight, rain or snow.
Don’t use aggressive or abradant detergent for the device surface cleaning.
Use soft wet cloth or tissue to remove strong dirt.
Attention!
As a result of continuous upgrades and functionality
improvements, technical characteristics of the device can
be changed without any preliminary declaration.
This manual can contain some inaccuracy or misprint.
The owner reserves the right to make corrections to the information
described in the user manual and device package.
Nature protection
Don’t throw away the device with other industrial or
nutritive trash if you see that symbol. Some regions have
separation and recycling systems for the electronic
equipment.
Connect with local authorities to receive information about recycling of
electronic equipment for your region.
Rights and limitation of liability
All rights reserved. Any part of that document can not be published in any
form, translated into other languages or reproduced in any way including
electronic or mechanical.
Document recording and copying is strictly denied without owner
permission.
!

SENSOR TYPE
1/2.9” CMOS
RESOLUTION
1920×1080 px.
VIDEO OUTPUT
AHD 1080p (2 MP), AHD 720p
(1 MP) or CVBS (PAL)
VIEW ANGLE
115˚
NIGHT BACKLIGHT
Infrared, 1.5 meters distance
LOCK RELAY CONTINUOUS CURRENT
1 A
VOLTAGE
+12 V
POWER CONSUMPTION
2.5 W in working mode
INSTALLATION TYPE
Surface or ush (optional) mount
DIMENSIONS
45×130×24 mm
WORKING TEMPERATURE
–40 ... +50 ˚C
ML-20HD
3 4
Table of contents
1. Package .......................................................................................................................... 4
2. Specication ................................................................................................................. 4
3. Description.................................................................................................................... 5
4. Schematic diagram .................................................................................................... 7
5. Installation..................................................................................................................... 8
6. Video camera output setting (AHD or PAL) ....................................................... 10
7. Limited Warranty......................................................................................................... 11
1. Package
ML-20HD outdoor panel − 1 pc.
Wall mounting bracket − 1 pc.
Angle bracket − 1 pc.
Rainshield − 1 pc.
Flush mounting box − 1 pc. (optional)
Mounting screws and anchors − 1 pkg.
User manual − 1 pc.
2. Specication

Wire colors
130 mm
45 mm 24 mm
1
2
3
4
5
6
7
8
5
1
2
3
7
8
4
6
ML-20HD
5 6
Red
Black
Yellow
White
Brown
Blue
Red & white
Power, +12 V
Ground (GND)
Video
Audio
N.O. relay contact
COM. relay contact
Video camera power, +12 V
3. Description
Microphone
Night infrared backlight
Video camera
Call button
Speaker
Video camera mode button
Communication cable
Speaker volume potentiometer

ML-20HD
7 8
4. Schematic diagram
Power (Red)
Audio (White)
GND (Black)
Video (Yellow)
N.O. (Brown)
COM.(Blue)
Lock
ML-20HD
Lock power
supply
Camera power
(Red & White)
Camera
power
suppply
(Optional for using cameara as
a source of video for DVR)
Angle mount
1) Take the angle bracket from the kit and place it 150-160 cm from the oor
line;
2) Mark and drill two halls inside the wall;
3) Take two anchors from the kit and hammer them into the drilled halls;
4) Fix angle bracket on the wall by two screws from the kit;
5) Fix wall mounting bracket on the angle bracket by two screws from the kit;
6) Connect all communication wires and x the door panel on the wall
mounting bracket by the screw from the down side.
5. Installation
SQ-07MT HD (Master)
*
Door 1
Door 2
InputOutput
Power
CCTV 1
CCTV 2

ML-20HD
9 10
6. Video camera output setting (AHD or PAL)
Outdoor panel video camera can work in three basic modes: AHD 1080p
(2 MP) – default mode, AHD 720p (1 MP) or analog CVBS (PAL). AHD is a
high-resolution mode, so it has better image quality than analog CVBS mode.
While using high-resolution AHD modes, the monitor must maintain that
kind of signal, otherwise there will be no image on the monitor screen.
To switch video camera modes remove resin cap on the back cover of the
outdoor panel. Then press and hold camera mode button during 5 seconds
to switch from the current mode to the next one in a such sequence:
AHD-H (1080P) →AHD-M (720P) → PAL →AHD-H (1080P) ...
Camera mode button
under resin cap
Speaker volume
potentiometer
under resin cap
Surface mount
1) Take the wall mounting bracket from the kit and place it 150-160 cm from
the oor line;
2) Mark and drill four halls inside the wall;
3) Take four anchors from the kit and hammer them into the drilled halls;
4) Fix wall mounting bracket by four screws from the kit;
5) Connect all communication wires and x the door panel on the wall
mounting bracket by the screw from the down side.

ML-20HD
11 12
7. Limited warranty
Manufacturer guarantees product normal functioning during the warranty
period if the user keeps all safety instructions described in that manual.
Warranty period is 12 months from the moment of the product purchasing
(warranty period could be extended up to 24 months or more, depending on
the local regulations).
Warranty period allows user to make guarantee repair in cases when normal
functioning of the product was violated by the fault of manufacturer and the
user haven’t oend transporting, installation and working conditions.
This limited warranty does not cover any damage to the product that results
from improper installation, accident, abuse, misuse, natural disaster,
insucient or excessive electrical supply, abnormal mechanical or
environmental conditions, or any unauthorized disassembly, repair or
modication.
Warranty void in such cases:
• the product was damaged by the fault of the customer;
• the product wasn’t properly installed according reccomendations from
the manual;
• the sticker on the backside of the product was broken;
• the product was not used for its intended function.
This limited warranty covers only repair, replacement, refund or credit for
defective products, as provided above. Manufacturer is not liable for, and
does not cover under warranty, any damages or losses of any kind
whatsoever resulting from loss of, damage to, or corruption of, content or
data or any costs associated with determining the source of system problems
or removing, servicing or installing products. This warranty excludes third
party software, connected equipment or stored data. Manufacturer is
therefore not liable for any losses or damage attributable to third party
software, connected equipment or stored data.
In the event a product has been discontinued, manufacturer shall either
repair the product, oer to replace it with a comparable product or provide a
refund at the lesser of the purchase price or the product’s current value.
Repaired or replacement products will continue to be covered by this limited
warranty for the remainder of the original warranty term.