Slinex SQ-07MT HD User manual

{ Design. Uniqueness. Innovation }
UNIQUE
DIRECT
SERIES
SQ-07MT 7” video door phone
with touch screen
Thank you for the
choice of our equipment
User manual

{ Design. Uniqueness. Innovation } UNIQUE
DIRECT
SERIES
1Rev. 1.0 2
Attention!
As a result of continuous upgrades and functionality improvements, technical
characteristics of the device can be changed without any preliminary declaration.
This manual can contain some inaccuracy or misprint. The owner reserves the right to
make corrections to the information described in the user manual and device package.
The last revision of this manual is available on www.slinex.com
Safety instructions
Read and keep that manual.
The device installation process should be carried out by the qulied specialists.
Use the device from –10 ˚C to +55 ˚C, always keep it within that temperature range.
Installation surface should be free from vibration and impact inuence.
Keep this device far from open sources of heat, such as radiators, heaters, and ovens.
The device can be installed near other electronic equipment in case if the temperature of the environment
does not exceed previously mentioned range.
The device should be protected from the direct inuence of the natural phenomena, such as direct sunlight,
rain or snow.
Don’t use aggressive or abradant detergent for the device surface cleaning.
Use soft wet cloth or tissue to remove strong dirt.
Don’t overpower outlets. It can cause re or electric shock.
Nature protection
Don’t throw away the device with other industrial or nutritive trash if you see that
symbol. Some regions have separation and recycling systems for the electronic
equipment. Connect with local authorities to receive information about recycling of
electronic equipment for your region.
Rights and limitation of liability
All rights reserved. Any part of that document can not be published in any form, translated into other
languages or reproduced in any way including electronic or mechanical.
Document recording and copying is strictly denied without owner permission.
Table of contents
1. Package ............................................................................................................................................................................................ 3
2. Specication...................................................................................................................................................................................3
3. Description......................................................................................................................................................................................4
4. Installation....................................................................................................................................................................................... 5
4.1 Cable requirements.......................................................................................................................................................5
4.2 Schematic diagrams......................................................................................................................................................6
4.3 Unit mount ....................................................................................................................................................................... 8
5. Operation.........................................................................................................................................................................................9
5.1 Incoming call ...................................................................................................................................................................9
5.2 Door panel and camera monitoring......................................................................................................................10
5.3 Incoming call redirection ..........................................................................................................................................11
5.4 Intercom ..........................................................................................................................................................................12
6. Monitor settings..........................................................................................................................................................................12
6.1 Main screen navigation..............................................................................................................................................12
6.2 System settings.............................................................................................................................................................13
6.3 Melody and volume settings ...................................................................................................................................15
6.4 Working mode settings..............................................................................................................................................16
6.5 Alarm settings ...............................................................................................................................................................17
6.6 Display settings.............................................................................................................................................................20
6.7 Snapshots and records playback............................................................................................................................21
7. Manual and automatic recording.........................................................................................................................................23
8. External sensors motion detection recording..................................................................................................................23
9. Limited Warranty.........................................................................................................................................................................24
!

{ Design. Uniqueness. Innovation } UNIQUE
DIRECT
SERIES
3 4
1
2
3
4
5
6
7
8
9
10
11
Microphone
«Intercom» button – call another monitor or incoming call redirection
«Monitor» button – door panel or camera image monitoring
«Answer» button – incoming call answer and start talking with the visitor
«Unlock» button – door unlocking
«Hang Up» button – stop conversation with the visitor / current system settings menu exit
MicroSD memory card slot (on the side of the monitor)
Touch display
Power LED. Active when the power is on.
First door panel LED. Active when the rst door panel is on.
Second door panel LED. Active when the second door panel is on.
1
9
10
11
127 мм
198 мм 20
мм 8
7
2 3 4 5 6
Screen
Resolution
Video system
Audio type
Call time
Internal memory
Memory extension slot
Standby mode power consumption
Working mode power consumption
Power supply
Mounting type
Size
Working temperature
7”, color TFT with touch screen
800×480 pixels
PAL/NTSC
Half duplex
120 seconds
100 snapshots
microSD, up to 32 GB
3 W
7 W
Built-in power supply, ~100–240 V
Surface mount
197×127×20 mm
−10...+55 ˚C
1. Package
SQ-07MT door monitor − 1 pc.
Wall mounting bracket − 1 pc.
Connection wires − 7 pcs.
Mounting screws and nuts − 1 pkg.
User manual − 1 pc.
2. Specication
3. Description

{ Design. Uniqueness. Innovation } UNIQUE
DIRECT
SERIES
5 6
4.2 Schematic diagrams
Diagram 1. SQ-07MT door panels, cameras, locks and TV connection.
Power
Audio
GND
Video
Not used
Signal
GND
Video
Lock
TV
Door
panel 1
Door
panel 2
SQ-07MT (Master)
Lock power
supply
Lock Lock power
supply
Video
GND
Door 1
Door 2
CCTV 1
CCTV 2
Input
Output
PowerTV out
GND
+13,5 V
*
Camera
power
suppply
Camera
power
suppply
Motion
sensor
Motion
sensor
CCTV 2
Video
GND
GND
+12 V
CCTV 1
4. Installation
4.1 Cable requirements
Disconnect all power cables before device installation.
This device can be connected with such cable types depends on the distance between door monitor and
door panel:
) Use 4-wire cable with such parameters:
• distance up to 25 meters use a cable with 0,22 mm square of one wire;
• distance 25 to 50 meters use a cable with 0,41 mm square of one wire;
• distance 50 to 100 meters use a cable with 0,75 mm square of one wire.
b) If the distance between door monitor and door panel is between 80 and 100 meters then use a 3-wire
cable with 0,75 mm square of one wire and RG-59 or RG-6 coaxial cable for the video signal.
c) Shielded or non-shielded twisted pair (not recommended):
• distance up to 25 meters non-shielded twisted pair can be used;
• distance 25 to 50 meters shielded twisted pair should be used.
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
0 - 50 m
Shield
Shield
50 - 80 m
80-100 m
RG-59 or RG-6 Video
GND
GND
+12 V
Not used
Signal
GND
Video
Power
Audio
GND
Video
0 - 25 m
25 - 50 m
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Shield Shield

{ Design. Uniqueness. Innovation } UNIQUE
DIRECT
SERIES
7 8
Door 1
Door 2
CCTV 1
CCTV 2
Input
Output
PowerTV out
Door 1
Door 2
CCTV 1
CCTV 2
Input
Output
PowerTV out
Door 1
Door 2
CCTV 1
CCTV 2
Input
Output
PowerTV out
Diagram 2. SQ-07MT system connection.
SQ-07MT (Master)
Door 1
Door 2
CCTV 1
CCTV 2
Input
Output
PowerTV out
SQ-07MT (Slave)
Notes:
* Use «Power»plug to connect external power supply +13,5 V. While use external power supply please keep
main power cord ~100-240 V disconnected from the outlet, otherwise it can damage monitor circuits.
** Door panels, cameras, power supplys, locks and motion sensors illustrated on the schemes are optional
devices and aren’t included into monitors kit.
Audio
GND
Data
Video
Audio
GND
Data
Video
Audio
GND
Data
Video
Audio
GND
Data
Video
Audio
GND
Data
Video
SQ-07MT (Slave) SQ-07MT (Slave)
4.3 Unit mount
1) Take the surface mount bracket from the kit and situate it 150-160 cm from the oor line.
2) Mark and drill four halls in the wall.
3) Take four nuts from the kit and hammer them into the drilled halls.
4) Fix surface mount bracket on the wall by four screws from the kit.
5) Connect all communication wires and x the monitor on the surface mount bracket.

{ Design. Uniqueness. Innovation } UNIQUE
DIRECT
SERIES
9 10
5.2 Door panel and camera monitoring
Standby mode
Monitor will display
the image from the
rst door panel
(monitoring time – 60 seconds)
Monitor will display
the image from the
second door panel
(monitoring time – 60 seconds)
Press «Monitor»
button or slide from
left to right side of
the screen
5. Operation
5.1 Incoming call
Standby mode
Standby mode
Melody is ringing on the
monitor and door panel,
image from the door panel
appears on the monitor screen
Visitor presses call button
on the rst door panel
Visitor presses call button
on the second door panel
Press «Answer» button or slide
from up to bottom side of
the screen to start conversation
with the visitor
Melody stops ringing and
conversation starts,
talking time is 120 seconds
Press «Hang up» button
or slide two fingers towards
each other to stop
conversation or incoming call
Press «Unlock» button or slide
from bottom to up side of the
screen to open lock connected
to the current door panel
Notes:
1) Monitor will be automatically switched into standby mode if the user doesn’t answer incoming call
during 60 seconds;
2) Image and sound from the door panel will be active during 20 seconds after the moment user presses
button. It let the user know if the visitor passed through the door.
20 seconds
20 seconds
Standby mode
Monitor will display
the image from the
rst CCTV camera
(monitoring time is unlimited)
Monitor will display
the image from the
second CCTV camera
(monitoring time is unlimited)
Press «Monitor»
button or slide from
left to right side of
the screen again
Press «Monitor»
button or slide from
left to right side of
the screen again
Press «Monitor»
button or slide from
left to right side of
the screen again
Press «Monitor»
button or slide from
left to right side of
the screen again
Press «Hang up» button
or slide two fingers towards
each other to stop
monitoring mode
Press «Answer» button or slide
from up to bottom side of
the screen to start conversation
with the visitor
Press «Unlock» button or slide
from bottom to up side of the
screen to open lock connected
to the current door panel

{ Design. Uniqueness. Innovation } UNIQUE
DIRECT
SERIES
11 12
5.4 Intercom
Two monitors connected into one system are used.
Melody starts
ringing
Standby mode
5.3 Incoming call redirection
Two monitors connected into one system are used.
Notes:
1) If only one door panel connected to the monitor then you can exit monitoring mode by pressing
«Monitor» button one more time. (all other sources of video signal should be disabled in the monitor
settings).
2) If several monitors connected into one system, the user can view the image from door panels and
cameras on any monitor inside this system. The image will be transferred from the «Master» monitor door
panels and cameras to the «Slave» monitors.
3) If someone presses call button on the door panel while monitoring is active then the image from this
door panel appears on the monitor screen and call melody starts. Press «Answer» button to start
conversation.
Note:
If incoming call was successfully redirected to the other monitor then current monitor will enter standby
mode.
Melody starts ringing on
the other monitor inside
the system and visitor image
appears on the monitor screen
Conversation with the
visitor on the other
monitor in progress
Incoming call from the
door panel and the
user starts conversation
Press «Intercom»
button or slide from
right to left side of
the screen to start
call redirection
20 seconds
Note:
If someone pressed call button on the door panel while intercom is active then the image from this door
panel will appear on the screen and call melody will starts. Press «Answer» button to start
conversation with the visitor.
6. Monitor settings
6.1 Main screen navigation
Press any place of the screen in standby mode to enter main screen. Then select and press any icon on the
screen to enter corresponding sub menu. Change any parameters by up and down arrows situated near
current parameter. After all settings have been made, press icon or press button to exit from
current sub menu. Press icon or press button to exit from the main screen. No need to save any
changes because they saved automatically after changing.
You can also monitor image from the door panels or cameras by entering «Monitor» menu from the main
screen and selecting appropriate video source.
Standby mode
Standby mode
Conversation with the
other monitor is in progress
Press «Answer» button or slide
from up to bottom side of
the screen to start conversation
Press «Answer» button or slide
from up to bottom side of
the screen to start conversation
with the visitor
Press «Unlock» button or slide
from bottom to up side of the
screen to open lock connected
to the current door panel
Press «Hang up» button
or slide two fingers towards
each other to stop
conversation or incoming call
Press «Hang up» button
or slide two fingers towards
each other to stop
conversation or incoming call
Press «Intercom»
button or slide from
right to left side of
the screen to start
intercom

Monitor System Ring
Alarm Color Files Exit
Mode
{ Design. Uniqueness. Innovation } UNIQUE
DIRECT
SERIES
13 14
6.2 System settings
Press «System» icon in the main menu to enter system settings of the monitor:
Release date − date of software release.
Format SD − micro SD card formatting. Please format microSD card before use it.
Recommended to use microSD cards of the 6-th class and above.
Format flash − internal memory formatting.
Backup pictures− copy files from the internal memory to microSD card.
Update −firmware updating of the monitor (place updating files on the microSD root folder).
Reboot − system reboot.
Following parameters are available in the «System» menu:
Language − the language of the settings menu.
Time − date and time settings.
Time display − date and time screensaver display in stndby mode (Off, 1, 3, 5, 10 min.).
Information:
Software version − current software version of the monitor.
Information
Time
Language
Main menu
Language
System
Main menu
Time
System
Main menu
System
Main menu
English
DD-MM-YY 08-07-2016 16:17
Time display: 10 min

{ Design. Uniqueness. Innovation } UNIQUE
DIRECT
SERIES
15 16
6.3 Melody and volume settings
Press «Ring» icon in the main menu to enter melody and volume settings.
Following parameters are available in the «Ring» menu:
Ring select − choose the melody for every door panel.
Ring volume −choose volume level (from 00 to 09) depending on the time of a day and also ringing
time of the melody (10-45 seconds).
Silence mode − incoming call melody and keyboard muting, «On» or «O».
6.4 Working mode settings
Press «Mode» icon in the main menu to enter working mode settings.
Following parameters are available in the «Mode» menu:
Mode − choose «Master» if you use one monitor in the system or if it’s the monitor which all the door
panels and CCTV cameras are connected to. Choose «Slave» if there is more than one monitor in the
system and no door panels or CCTV cameras connected to this monitor.
Door 2 status − «On» or «O», include or exclude second door panel from the monitoring list.
Software version: 1.1.3.2
Release date: 2016-07-08
Format SD
Format flash
Backup pictures
Update
Reboot
Ring VolumeRing Select
Door 1 01
Door 2 02
Ring vol 1: 08 : 00 ~ 18 : 00 08 30 sec
Ring vol 2: 18 : 00 ~ 23 : 00 04 30 sec
Ring vol 3: 23 : 00 ~ 08 : 00 01 30 sec
Silence mode: Off
System
Main menu
Information
Main menu
Ring
Ring select
Main menu
Ring
Ring volume
Main menu
Ring

{ Design. Uniqueness. Innovation } UNIQUE
DIRECT
SERIES
17 18
6.5 Alarm settings
Press «Alarm» icon in the main menu to enter alarm settings.
Following parameters are available in the «Alarm» menu:
CAM alarm –additional cameras alarm settings;
Motion detect –software motion detection.
CAM alarm includes next sub menu:
CAM1 sensor type: «NO», motion sensor with normally disconnected contacts are used;
«NC», motion sensor with normally connected contacts are used;
«O», motion sensor doesn’t used.
CAM2 sensor type: «NO», motion sensor with normaly disconnected contacts are used;
«NC», motion sensor with normaly connected contacts are used;
«O», motion sensor doesn’t used.
CAM1 − «On» or «O», include or exclude first CCTV camera from the monitoring list.
CAM2 − «On» or «O», include or exclude second CCTV camera from the monitoring list.
CAM1 ring time − alarm melody ringing time activated by CAM1 motion sensor, from 00 to 30
seconds.
CAM2 ring time − alarm melody ringing time activated by CAM2 motion sensor, from 00 to 30
seconds.
Alarm record: «Snapshot» − save photo if motion detection has occurred;
«Record» − save video if motion detection has occurred.
Mode:
Door 2 status:
Record mode:
Door 1 unlock time:
Door 2 unlock time:
Key backlight:
Keyboard sound:
Record mode: «Snapshot» – take snapshot while incoming call or manually;
«Record» – record video while incoming call or manually.
Door 1 unlock time − Door 1 relay delay time, 2 –10 seconds.
Door 2 unlock time − Door 2 relay delay time, 2 –10 seconds.
Key backlight − «On» or «O».
Keyboard sound − «On» or «O».
Main menu
Mode
Main menu
Alarm
CAM alarm
Main menu
Alarm
Motion detect
CAM alarm
Master
On
Snapshot
02 sec
03 sec
On
Off
CAM1 sensor type:
CAM2 sensor type:
CAM1:
CAM2:
CAM1 ring time:
CAM2 ring time:
Alarm record:
NO
NO
On
On
10 sec
10 sec
Record

{ Design. Uniqueness. Innovation } UNIQUE
DIRECT
SERIES
19 20
6.6 Display settings
Press «Color» icon in the main menu to enter display settings.
Following parameters are available in the «Color» menu:
Door1 − image settings for the rst door panel.
Door2 −image settings for the second door panel.
CAM1 − image settings for the rst CCTV camera.
CAM2 − image settings for the second CCTV camera.
Door1 Door2
CAM1 CAM2
Main menu
Color
Software motion detector can observe and detect motion without any external sensors using any camera
image changes with the time. Camera power that is used for motion detection should be constantly on to
let the monitor log image changes and detect motion.
Motion detect includes next sub menu:
Motion detect source: «O» – software detector is o;
«Door1» – motion detection on Door1;
«Door2» – motion detection on Door2;
«CAM1» – motion detection on CAM1;
«CAM2» – motion detection on CAM2.
Motion detect area −set image area which motion detection is performed.
Store mode: «Snapshot» – save photo if software motion detection has occurred;
«Record» – save video if software motion detection has occurred.
Notication − «On» or «O». Enable or disable sound alarm if software motion detection has
occurred.
Main menu
Alarm
Motion detect
Main menu
Alarm
Motion detect
Motion detect area
Motion detect source:
Motion detect area
Store mode:
Notification:
Door1
Snapshot
Off
+–

0005 / 0005
20150831 - 120548
CAM1
25
25
25
{ Design. Uniqueness. Innovation } UNIQUE
DIRECT
SERIES
21 22
Every video source has its own image settings:
Brightness – parameter range from 0 to 50, 25 used by default.
Contrast – parameter range from 0 to 50, 25 used by default.
Color – parameter range from 0 to 50, 25 used by default.
Select «Record files» or «Snapshot files» icon, then press file name to start playing.
While playing press button to go back to the les list.
If you want to delete the file press and hold the finger for two seconds on selected file name. File context
menu will appear on the screen. Select one of three options:
Play – current le playing;
Delete current le – current file deleting;
Delete all les – all les deleting
or press button to close context menu.
Main menu
Color
Door1
Door2
CAM1
CAM2
6.7 Snapshots and records playback
Press «Files» icon in the main menu to enter snapshots and records playback.
Following parameters are available in the «Files» menu:
Record les − records playback.
Snapshot les −snapshot les playback
Record Files
Main menu
Files
12 : 10 : 35
31 - 08 - 2015
Record files
Main menu
Files
Main menu
Files
001 / 003
20150831 - 121033 0005
20150831 - 120548 0004
20150831 - 120234 0003
20150831 - 115828 0002
20150831 - 115630 0001
Play
Delete current file
Delete all files
Record files Snapshot files

{ Design. Uniqueness. Innovation } UNIQUE
DIRECT
SERIES
23 24
7. Manual and automatic recording
User can take snapshots or record video during monitoring door panel or CCTV camera. Press
icon on the screen to take snapshot or press icon on the screen to start video recording. Press the
same button second time to stop video recording.
Depending on the «Record mode» setting (page 17) monitor will be automatically taking snapshots or
recording video while incoming call from the door panel.
Note:
Video can be recorded only if microSD card installed into monitor slot. If microSD is absent then monitor
can only record snapshots using internal memory, no metter what «Record mode» has been set.
100 snapshots can be stored in the internal memory. If the quantity exceeds 100 snapshots then older
snapshots will be replaced by new one.
8. External sensors motion detection recording
Camera 1 and Camera 2 has motion detection function by external motion sensor. When external sensor
connects or disconnects its contacts (depending on «CAM1 sensor type» or «CAM2 sensor type» setting
in «Alarm» →«CAM alarm» menu, page 17-18), recording starts on the door monitor. Video recording time
is 10 seconds. Press button to stop recording manually.
Use any external sensors that has normaly opened «NO» or normaly closed «NC» contacts. When the sensor
is activated it connects (NO case) or disconnects (NC case) contacts which activates recording on the door
monitor.
+12 V
Ground
Ground
Video
Camera
power
supply
Motion sensor
CCTV camera
Not used
Signal
Ground
Video
External motion sensor connection.
9. Limited warranty
Manufacturer guarantees product normal functioning during the warranty period if the user keeps all safety
instructions described in that manual.
Warranty period is 12 months from the moment of the product purchasing (warranty period could be
extended up to 24 months or more, depending on the local regulations).
Warranty period allows user to make guarantee repair in cases when normal functioning of the product was
violated by the fault of manufacturer and the user haven’t oend transporting, installation and working
conditions.
This limited warranty does not cover any damage to the product that results from improper installation,
accident, abuse, misuse, natural disaster, insucient or excessive electrical supply, abnormal mechanical or
environmental conditions, or any unauthorized disassembly, repair or modication.
Warranty void in such cases:
• the product was damaged by the fault of the customer;
• the product wasn’t properly installed according reccomendations from the manual;
• the sticker on the backside of the product was broken;
• the product was not used for its intended function.
This limited warranty covers only repair, replacement, refund or credit for defective products, as provided
above. Manufacturer is not liable for, and does not cover under warranty, any damages or losses of any kind
whatsoever resulting from loss of, damage to, or corruption of, content or data or any costs associated with
determining the source of system problems or removing, servicing or installing products. This warranty
excludes third party software, connected equipment or stored data. Manufacturer is therefore not liable for
any losses or damage attributable to third party software, connected equipment or stored data.
In the event a product has been discontinued, manufacturer shall either repair the product, oer to replace
it with a comparable product or provide a refund at the lesser of the purchase price or the product’s current
value.
Repaired or replacement products will continue to be covered by this limited warranty for the remainder of
the original warranty term.