Slinex SM-04M User manual

{ Design. Uniqueness. Innovation }
DESIGN
DIRECT
SERIES
SM-04M 4” video door phone
Thank you for the
choice of our equipment
User manual

{ Design. Uniqueness. Innovation } DESIGN
DIRECT
SERIES
1 2
Rev. 1.0
Attention!
As a result of continuous upgrades and functionality improvements, technical
characteristics of the device can be changed without any preliminary declaration.
This manual can contain some inaccuracy or misprint. The owner reserves the right to
make corrections to the information described in the user manual and device package.
The last revision of this manual is available on www.slinex.com
Safety instructions
Read and keep that manual.
The device installation process should be carried out by the qulied specialists.
Use the device from the –10 ˚C to +55 ˚C, always keep it within that temperature range.
Installation surface should be free from vibration and impact inuence.
Keep this device far from open sources of heat, such as radiators, heaters, and ovens.
The device can be installed near other electronic equipment in case if the temperature of the environment
does not exceed previously mentioned range.
The device should be protected from the direct inuence of the natural phenomena, such as direct sunlight,
rain or snow.
Don’t use aggressive or abradant detergent for the device surface cleaning.
Use soft wet cloth or tissue to remove strong dirt.
Don’t overpower outlets. It can cause re or electric shock.
Nature protection
Don’t throw away the device with other industrial or nutritive trash if you see that
symbol. Some regions have separation and recycling systems for the electronic
equipment. Connect with local authorities to receive information about recycling of
electronic equipment for your region.
Rights and limitation of liability
All rights reserved. Any part of that document can not be published in any form, translated into other
languages or reproduced in any way including electronic or mechanical.
Document recording and copying is strictly denied without owner permission.
Table of contents
1. Package ............................................................................................................................................................................................3
2. Specication...................................................................................................................................................................................3
3. Description......................................................................................................................................................................................4
4. Installation.......................................................................................................................................................................................5
4.1 Cable requirements.......................................................................................................................................................5
4.2 Schematic diagrams......................................................................................................................................................6
4.3 Unit mount .......................................................................................................................................................................7
5. Operation.........................................................................................................................................................................................8
5.1 Incoming call ...................................................................................................................................................................8
5.2 Door panel and camera image monitoring..........................................................................................................9
5.3 Incoming call redirection .........................................................................................................................................10
5.4 Intercom .........................................................................................................................................................................11
6. Monitor settings......................................................................................................................................................................... 11
6.1 Display settings............................................................................................................................................................ 12
7. Snapshots recording and viewing....................................................................................................................................... 13
8. Limited Warranty........................................................................................................................................................................14
!

3. Description
7
8
6
52 4 3
1
{ Design. Uniqueness. Innovation } DESIGN
DIRECT
SERIES
3 4
1
2
3
4
5
6
7
8
Display
«Monitor» button – door panel or camera image monitoring
«Answer» button – incoming call answer and start talking with the visitor
«Unlock» button – door unlocking
«Hang Up» – stop conversation with the visitor / settings menu exit
Volume joystick:
• move joystick up or down during intercom to increase or decrease talking volume;
• push the joystick while monitoring to save a photo;
• push the joystick while standby to enter photo viewing mode
Settings joystick:
• push the joystick any time to enter settings menu;
• move joystick up or down to move through the settings menu (next/previous parameter);
• push the joystick on any parameter to change its value. Change the value of current
parameter by moving joystick up or down and then push the joystick again to save the
parameter.
Microphone
169 mm
118 mm 20
mm
Screen
Resolution
Video system
Audio type
Call time
Internal memory
Memory extension slot
Standby mode power consumption
Working mode power consumption
Power supply
Mounting type
Size
Working temperature
4”, color TFT (4:3)
320×240 pixels
PAL/NTSC
Half duplex
120 seconds
250 photos
No
1 W
6 W
Built-in power supply, ~100–240 V
Surface mount
118×169×20 mm
−10...+55 ˚C
1. Package
SM-04M door monitor − 1 pc.
Wall mounting bracket − 1 pc.
Connection wires − 5 pcs.
Mounting screws and nuts − 1 pkg.
User manual − 1 pc.
2. Specication

{ Design. Uniqueness. Innovation } DESIGN
DIRECT
SERIES
5 6
SM-04M (Master)
Door 1
Door 2
Input
Output
PowerCCTV1/2
Door 1
Door 2
Input
Output
PowerCCTV1/2
GND
+13,5 V
*
SM-04M (Slave)
CCTV 2
CCTV 1
4.2 Schematic diagrams
SM-04M door panels, cameras and locks connection.
4. Installation
4.1 Cable requirements
Disconnect all power cables before device installation.
This device can be connected with such cable types depends on the distance between door monitor and
door panel:
) Use 4-wire cable with such parameters:
• distance up to 25 meters use a cable with 0,22 mm square of one wire;
• distance 25 to 50 meters use a cable with 0,41 mm square of one wire;
• distance 50 to 100 meters use a cable with 0,75 mm square of one wire.
b) If the distance between door monitor and door panel is between 80 and 100 meters then use a 3-wire
cable with 0,75 mm square of one wire and RG-59 or RG-6 coaxial cable for the video signal.
c) Shielded or non-shielded twisted pair (not recommended):
• distance up to 25 meters non-shielded twisted pair can be used;
• distance 25 to 50 meters shielded twisted pair should be used.
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
0 - 50 m
Shield
Shield
50 - 80 m
80-100 m
RG-59 or RG-6
0 - 25 m
25 - 50 m
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Shield Shield
Lock
Door
panel 1
Lock power
supply
CCTV power
supply
CCTV power
supply
Lock
Door
panel 2
Lock power
supply
+12 V
GND
GND
Video
+12 V
GND
GND
Video
Video 1
GND
GND
Video 2
Power
Audio
GND
Video
Power
Audio
GND
Video
Audio
GND
Data
Video
Audio
GND
Data
Video
Notes:
* Use «Power»plug on the monitor to connect external power supply +13,5 V. While use
external power supply please keep main power cord ~100-240 V disconnected from the outlet,
otherwise it can damage monitor circuits.
** Door panels, cameras, power supplys and locks, described on the diagram are optional
devices and are not included into monitor kit.

{ Design. Uniqueness. Innovation } DESIGN
DIRECT
SERIES
7 8
4.3 Unit mount
1) Take the surface mount bracket from the kit and situate it 150-160 cm from the oor line.
2) Mark and drill four halls in the wall.
3) Take four nuts from the kit and hammer them into the drilled halls.
4) Fix surface mount bracket on the wall by four screws from the kit.
5) Connect all communication wires and x the monitor on the surface mount bracket.
5. Operation
5.1 Incoming call
Standby mode
Standby mode
Melody is ringing on the
monitor and door panel,
image from the door panel
appears on the monitor screen
Visitor presses call button
on the rst door panel
Visitor presses call button
on the second door panel
Press «Answer» button to start
conversation with the visitor
Melody stops ringing and
conversation starts,
talking time is 120 seconds
Press «Hang up» button to
stop conversation or
incoming call
Press «Unlock» button to open
lock connected to the current
door panel, relay built into the
panel will open the lock
Notes:
1) Monitor will be automatically switched into standby mode if the user doesn’t answer incoming call
during 60 seconds;
2) Image and sound from the door panel will be active during 20 seconds after the moment user presses
button. It let the user know if the visitor passed through the door.
20 seconds

{ Design. Uniqueness. Innovation } DESIGN
DIRECT
SERIES
9 10
5.2 Door panel and camera image view
Standby mode
Monitor will display
the image from the
rst door panel
(monitoring time – 60 seconds)
Monitor will display
the image from the
second door panel
(monitoring time – 60 seconds)
Press «Monitor»
button on the
monitor
20 seconds
Standby mode
Press «Monitor»
button on the
monitor again
Press «Monitor»
button on the
monitor again
Press «Monitor»
button on the
monitor again
Press «Monitor»
button on the
monitor again
Monitor will display
the image from the
rst CCTV camera
(monitoring time is unlimited)
Monitor will display
the image from the
second CCTV camera
(monitoring time is unlimited)
Press «Hang up» button to
stop monitoring or
conversation
Press «Answer» button to start
conversation with the visitor
Press «Unlock» button to open
lock connected to the current
door panel, relay built into the
panel will open the lock
5.3 Incoming call redirection
Two monitors connected into one system are used.
Notes:
1) If only one door panel connected to the monitor then you can escape monitoring mode by pressing
«Monitor» button one more time. (all other sources of video signal should be disabled in the monitor
settings).
2) If several monitors connected into one system, the user can view the image from door panels and
cameras on any monitor inside this system. The image will be transferred from the «Master» monitor door
panels and cameras to the «Slave» monitors.
3) If someone press call button on the door panel while monitoring is active then the image from this door
panel appears on the monitor screen and call melody starts. Press «Answer» button to start
conversation.
Note:
If incoming call was successfully redirected to the other monitor and other user answered the call then
current monitor will enter standby mode.
Melody starts ringing on
the other monitor inside
the system and visitor image
appears on the monitor screen
Conversation with the
visitor on the other
monitor begins
Incoming call from the
door panel and the
user starts conversation
Press «Answer»
button to start
call redirection
20 seconds
Press «Answer» button on the
other monitor to start
conversation with the visitor
Standby mode
Press «Unlock» button to open
lock connected to the current
door panel, relay built into the
panel will open the lock
Press «Hang up» button to
stop conversation or
incoming call

{ Design. Uniqueness. Innovation } DESIGN
DIRECT
SERIES
11 12
Enter monitor settings like it described above.
The next parameters are available in the monitor settings:
Language – choose the monitor settings language;
Date – current date set;
Time – current time set;
Ring 1 – melody and volume for the rst door panel;
Ring 2 – melody and volume for the second door panel;
Delete all – delete all photos from the monitor memory;
Mode:choose «Master», if any door panels or cameras connected to this door monitor, otherwise choose
«Slave»;
Door 2 – include or exclude second door panel from the monitoring list;
Cam – include or exclude CCTV cameras from the monitoring list;
Unlock – lock relay open time (from 02 up to 10 seconds);
Exit – exit monitor settings.
If the user does not use the monitor (does not monitors door panel or camera, does not makes any settings),
then the monitor will be automaticaly pushed into standby mode after 1 minute of no actions.
6.1 Display settings
Push the joystick in monitoring or talking mode to enter display settings. Use the manual from the
previous page to navigate through the menu. Brightness, contrast and chroma can be changed in the
range from 0 up to 50. Default values for every parameter is 25.
Choose «Exit» parameter and push joystick to exit from the display settings.
Also you can press button to exit.
Note:
If someone press call button on the door panel while intercom is active then the image from this door panel
appears on the monitor screen and call melody starts. Press «Answer» button to start conversation
with the visitor.
6. Monitor settings
Settings joystick situated on the right side of the monitor case. It has several functions:
• push the joystick in stanby mode to enter monitor settings;
• move the joystick up or down to change current parameter of the
monitor settings;
• push the joystick again to choose current parameter and move it up
or down to change parameter value;
• push the joystick one more time to save current parameter setting.
Volume joystick also situated on the right side of the monitor case and has such functions:
• push the joystick in monitoring or talking mode to save a photo;
• push the joystick in standby mode to enter photo viewing mode.
Languge
Date
Time
Ring 1
Ring 2
Delete all
English
2016-28-10
11:31:15
08 08
08 08
8
1
2
Mode
Door 2
Cam
Unlock
Exit
Master
Enable
Enable
02s
Brightness
Contrast
Chroma
Exit
25
25
25
5.4 Intercom
Two monitors connected into one system are used.
Melody starts
ringing
Standby mode
Standby mode
Press «Answer»
button to start
intercom
conversation
Conversation with the
other monitor starts
Press «Answer» button on
the other monitor to start
conversation
Press «Hang up»
button to stop
conversation
Move up
Move down
Push

{ Design. Uniqueness. Innovation } DESIGN
DIRECT
SERIES
13 14
7. Snapshot recording and viewing
Monitor automatically take snapshot every time visitor pushes the call button on the door panel. Push the
joystick in monitoring or talking mode to take manual snapshot. Internal memory capacity is 250
snapshots. If snapshots quantity exceeds 250, then most old snapshots will be deleted.
Push the joystick in standby mode to enter snapshot viewing mode.
Move the joystick up or down, to view next/previous snapshot.
Push the joystick while viewing to delete current snapshot. Blinking icon will appear on the
display. Push the joystick again to conrm snapshot deleting.
If you want to delete all snapshots from the monitors memory then go to the «Delete all» parameter in the
monitor settings menu and push the joystick on that parameter to start deleting.
Press button any time to exit snapshot viewing mode.
2015/10/09 17:23:47
01/27 Unview 01
8. Limited warranty
Manufacturer guarantees product normal functioning during the warranty period if the user keeps all safety
instructions described in that manual.
Warranty period is 12 months from the moment of the product purchasing (warranty period could be
extended up to 24 months or more, depending on the local regulations).
Warranty period allows user to make guarantee repair in cases when normal functioning of the product was
violated by the fault of manufacturer and the user haven’t oend transporting, installation and working
conditions.
This limited warranty does not cover any damage to the product that results from improper installation,
accident, abuse, misuse, natural disaster, insucient or excessive electrical supply, abnormal mechanical or
environmental conditions, or any unauthorized disassembly, repair or modication.
Warranty void in such cases:
• the product was damaged by the fault of the customer;
• the product wasn’t properly installed according reccomendations from the manual;
• the sticker on the backside of the product was broken;
• the product was not used for its intended function.
This limited warranty covers only repair, replacement, refund or credit for defective products, as provided
above. Manufacturer is not liable for, and does not cover under warranty, any damages or losses of any kind
whatsoever resulting from loss of, damage to, or corruption of, content or data or any costs associated with
determining the source of system problems or removing, servicing or installing products. This warranty
excludes third party software, connected equipment or stored data. Manufacturer is therefore not liable for
any losses or damage attributable to third party software, connected equipment or stored data.
In the event a product has been discontinued, manufacturer shall either repair the product, oer to replace
it with a comparable product or provide a refund at the lesser of the purchase price or the product’s current
value.
Repaired or replacement products will continue to be covered by this limited warranty for the remainder of
the original warranty term.