Slinex UNIQUE DIRECT Series User manual

{ Design. Uniqueness. Innovation }
SM-07M 7” video door phone
Thank you for the
choice of our equipment
User manual
UNIQUE
DIRECT
SERIES

{ Design. Uniqueness. Innovation }
1 2
Rev. 1.0
Attention!
As a result of continuous upgrades and functionality improvements, technical
characteristics of the device can be changed without any preliminary declaration.
This manual can contain some inaccuracy or misprint. The owner reserves the right to
make corrections to the information described in the user manual and device package.
The last revision of this manual is available on www.slinex.com
Safety instructions
Read and keep that manual.
The device installation process should be carried out by the qulied specialists.
Use the device from the –10 ˚C to +55 ˚C, always keep it within that temperature range.
Installation surface should be free from vibration and impact inuence.
Keep this device far from open sources of heat, such as radiators, heaters, and ovens.
The device can be installed near other electronic equipment in case if the temperature of the environment
does not exceed previously mentioned range.
The device should be protected from the direct inuence of the natural phenomena, such as direct sunlight,
rain or snow.
Don’t use aggressive or abradant detergent for the device surface cleaning.
Use soft wet cloth or tissue to remove strong dirt.
Don’t overpower outlets. It can cause re or electric shock.
Nature protection
Don’t throw away the device with other industrial or nutritive trash if you see that
symbol. Some regions have separation and recycling systems for the electronic
equipment. Connect with local authorities to receive information about recycling of
electronic equipment for your region.
Rights and limitation of liability
All rights reserved. Any part of that document can not be published in any form, translated into other
languages or reproduced in any way including electronic or mechanical.
Document recording and copying is strictly denied without owner permission.
Table of contents
1. Package ......................................................................................................................................................................................... 3
2. Specication................................................................................................................................................................................ 3
3. Description................................................................................................................................................................................... 4
4. Installation.................................................................................................................................................................................... 5
4.1 Cable requirements.................................................................................................................................................... 5
4.2 Schematic diagrams................................................................................................................................................... 6
4.3 Unit mount .................................................................................................................................................................... 7
5. Operation...................................................................................................................................................................................... 8
5.1 Incoming call ................................................................................................................................................................8
5.2 Door panel and camera image monitoring....................................................................................................... 9
5.3 Incoming call redirection ......................................................................................................................................... 10
5.4 Intercom ......................................................................................................................................................................... 11
6. Monitor settings......................................................................................................................................................................... 11
6.1 Melody settings ........................................................................................................................................................... 12
6.2 Image settings.............................................................................................................................................................. 12
6.3 Date and time settings.............................................................................................................................................. 12
6.4 System settings............................................................................................................................................................ 13
6.5 Record settings ............................................................................................................................................................ 13
7. Limited Warranty........................................................................................................................................................................ 14
!
UNIQUE
DIRECT
SERIES

{ Design. Uniqueness. Innovation }
3 4
1
2
3
4
5
6
7
8
9
10
11
123 mm
193 mm 18
mm
UNIQUE
DIRECT
SERIES
1. Package
SM-07M door monitor − 1 pc.
Wall mounting bracket − 1 pc.
Connection wires − 6 pcs.
Mounting screws and nuts − 1 pkg.
User manual − 1 pc.
2. Specication
Screen
Resolution
Video system
Audio type
Call time
Internal memory
Memory extension slot
Standby mode power consumption
Working mode power consumption
Power supply
Mounting type
Dimensions
Working temperature
7”, color TFT (16:9)
800×480 pixels
PAL/NTSC
Half duplex
120 seconds
100 snapshots
MicroSD, up to 32 GB
3 W
6 W
Built-in power supply, ~100–240 V
Surface mount
193×123×18 mm
−10...+55 ˚C
5
2
1
47
6
3
8
9
10
11
3. Description
Display
Microphone
«Intercom» button – call another monitor or incoming call redirection
«Monitor» button – door panel or camera image monitoring
«Answer» button – incoming call answer and start conversation with the visitor
«Unlock» button – door unlocking
«Hang Up» button – stop conversation with the visitor / settings menu exit
MicroSD card slot
Speaker
Volume joystick:
• move the joystick up or down during intercom or conversation to increase or decrease
monitor speaker volume;
Settings joystick:
• move the joystick up while monitoring or conversation to save a photo or start video
recording (depends on record settings). Move the joystick down to stop video
recording;
• push the joystick in standby mode to enter settings menu;
• move joystick up or down to move through the settings menu (next/previous
parameter);
• push the joystick on any parameter to change its value. Change the value of current
parameter by moving joystick up or down and then push the joystick again to save
current parameter.

{ Design. Uniqueness. Innovation }
5 6
UNIQUE
DIRECT
SERIES
SM-07M (Master)
Door 1
Door 2
Input
Output
PowerCCTV1/2
Door 1
Door 2
Input
Output
PowerCCTV1/2
GND
+13,5 V
*
SM-07M (Slave)
CCTV 2
CCTV 1
4.2 Schematic diagrams
SM-07M door panels, cameras and locks connection.
4. Installation
4.1 Cable requirements
Disconnect all power cables before device installation.
This device can be connected with such cable types depends on the distance between door monitor and
door panel:
) Use 4-wire cable with such parameters:
• distance up to 25 meters use a cable with 0,22 mm square of one wire;
• distance 25 to 50 meters use a cable with 0,41 mm square of one wire;
• distance 50 to 100 meters use a cable with 0,75 mm square of one wire.
b) If the distance between door monitor and door panel is between 80 and 100 meters then use a 3-wire
cable with 0,75 mm square of one wire and RG-59 or RG-6 coaxial cable for the video signal.
c) Shielded or non-shielded twisted pair (not recommended):
• distance up to 25 meters non-shielded twisted pair can be used;
• distance 25 to 50 meters shielded twisted pair should be used.
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
0 - 50 m
Shield
Shield
50 - 80 m
80-100 m
RG-59 or RG-6
0 - 25 m
25 - 50 m
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Shield Shield
Lock
Door
panel 1
Lock power
supply
CCTV power
supply
CCTV power
supply
Lock
Door
panel 2
Lock power
supply
+12 V
GND
GND
Video
+12 V
GND
GND
Video
Video 1
GND
GND
Video 2
Power
Audio
GND
Video
Power
Audio
GND
Video
Audio
GND
Data
Video
Audio
GND
Data
Video
Notes:
* Use «Power»plug to connect external power supply +13,5 V. While using external power
supply please keep main power cord ~100-240 V disconnected from the outlet, otherwise it
can damage monitor circuits.
** Door panels, cameras, power supplys and locks, described on the diagram are optional
devices and are not included into monitor kit.

7 8
{ Design. Uniqueness. Innovation } UNIQUE
DIRECT
SERIES
4.3 Unit mount
1) Take the surface mount bracket from the kit and situate it 150-160 cm from the oor line.
2) Mark and drill four halls in the wall.
3) Take four nuts from the kit and hammer them into the drilled halls.
4) Fix surface mount bracket on the wall by four screws from the kit.
5) Connect all communication wires and x the monitor on the surface mount bracket.
5. Operation
5.1 Incoming call
Standby mode
Standby mode
Melody is ringing on the
monitor and door panel,
image from the door panel
appears on the monitor screen
Visitor presses call button
on the rst door panel
Visitor presses call button
on the second door panel
Press «Answer» button to start
conversation with the visitor
Melody stops ringing and
conversation starts,
talking time is 120 seconds
Press «Hang up» button to
stop conversation or
incoming call
Press «Unlock» button to open
lock connected to the current
door panel, relay built into the
panel will open the lock
Notes:
1) Monitor will be automatically switched into standby mode if the user doesn’t answer incoming call
during 60 seconds;
2) Image and sound from the door panel will be active during 20 seconds after the moment user presses
button. It let the user know if the visitor passed through the door.
20 seconds

{ Design. Uniqueness. Innovation }
9 10
5.2 Door panel and camera image view
Standby mode
Monitor will display
the image from the
rst door panel
(monitoring time – 60 seconds)
Monitor will display
the image from the
second door panel
(monitoring time – 60 seconds)
Press «Monitor»
button on the
monitor
20 seconds
Standby mode
Press «Monitor»
button on the
monitor again
Press «Monitor»
button on the
monitor again
Press «Monitor»
button on the
monitor again
Press «Monitor»
button on the
monitor again
Monitor will display
the image from the
rst CCTV camera
(monitoring time is unlimited)
Monitor will display
the image from the
second CCTV camera
(monitoring time is unlimited)
Press «Hang up» button to
stop monitoring or
conversation
Press «Answer» button to start
conversation with the visitor
Press «Unlock» button to open
lock connected to the current
door panel, relay built into the
panel will open the lock
UNIQUE
DIRECT
SERIES
5.3 Incoming call redirection
Two monitors connected into one system are used.
Notes:
1) If only one door panel connected to the monitor then you can escape monitoring mode by pressing
«Monitor» button one more time. (all other sources of video signal should be disabled in the monitor
settings).
2) If several monitors connected into one system, the user can view the image from door panels and
cameras on any monitor inside this system. The image will be transferred from the «Master» monitor door
panels and cameras to the «Slave» monitors.
3) If someone press call button on the door panel while monitoring is active then the image from this door
panel appears on the monitor screen and call melody starts. Press «Answer» button to start
conversation.
Note:
If incoming call was successfully redirected to the other monitor then current monitor will enter standby
mode.
Melody starts ringing on
the other monitor inside
the system and visitor image
appears on the monitor screen
Conversation with the
visitor on the other
monitor begins
Incoming call from the
door panel and the
user starts conversation
Press «Intercom»
button to start
call redirection
20 seconds
Press «Answer» button on the
other monitor to start
conversation with the visitor
Standby mode
Press «Unlock» button to open
lock connected to the current
door panel, relay built into the
panel will open the lock
Press «Hang up» button to
stop conversation or
incoming call

{ Design. Uniqueness. Innovation }
11 12
6.1 Melody settings
Enter monitor settings in the way like it described on the previous page:
Ring select − ring melody selection (16 melodies are available);
Ring time − melody ringing time in seconds;
Ring vol 1 − melody ringing volume for the rst time zone;
Ring vol 2 − melody ringing volume for the second time zone;
Ring vol 3 − melody ringing volume for the third time zone;
Exit − monitor settings exit.
Note:
If there is some time interval between time zones then maximum volume will be applied during this time
interval.
6.2 Image settings
English − interface language selection;
Brightness − image brightness level tuning;
Chroma − image chroma level tuning;
Contrast − image contrast level tuning;
Exit − monitor settings exit.
6.3 Date and time settings
Time − date and time settings;
Key tone − touch button sounds enable (On) or disable (O);
Reboot − reboot the monitor;
Version − current software version and release date;
Exit − monitor settings exit.
Ring select
Ring time
Ring vol 1 08:00 - 12:00
Ring vol 2 12:00 - 18:00
Ring vol 3 18:00 - 08:00
Exit
15
30s
04
06
03
English
Brightness
Chroma
Contrast
Exit
050
050
050
Time
Key tone
Reboot
Version
Exit
2015-06-08 15:49
Off
1-0-8 2017-05-01
5.4 Intercom
Two monitors connected into one system are used.
Melody starts
ringing
Standby mode
Note:
If somebody presses call button on the door panel while intercom is active then the image from the door
panel appears on the monitor screen and call melody starts. Press «Answer» button to start
conversation with the visitor.
6. Monitor settings
Settings joystick situated on the right side of the monitor case. It has several functions:
• push the joystick in stanby mode to enter monitor settings;
• move the joystick up or down to change current parameter
of the monitor settings;
• push the joystick again to choose current parameter and move
it up or down to change current parameter value;
• push the joystick one more time to save current parameter
value.
Standby mode
Press «Intercom»
button to start
intercom
conversation
Conversation with the
other monitor starts
Press «Answer» button on
the other monitor to start
conversation
Press «Hang up»
button to stop
conversation
UNIQUE
DIRECT
SERIES
Move down
Move up
Push

{ Design. Uniqueness. Innovation }
13 14
6.4 System settings
Unlock time − lock relay activation time;
Mode − select «Master» if all door panels and cameras connected to this monitor, otherwise select «Slave»
if this monitor connected as a secondary in the system;
Door 2 − include (On) or exclude (O) Door 2 from the monitoring list;
Cam 1 − include (On) or exclude (O) Camera 1 from the monitoring list;
Cam 2 − include (On) or exclude (O) Camera 2 from the monitoring list;
Exit − monitor settings exit.
6.5 Record settings
Record − monitor record mode: «O» − snapshots recording;
«On» − video recording;
Play − snapshots or video playing. Move joystick up or down to go to the next/previous file playing;
Backup − snapshots backup from internal memory to microSD card;
Format − internal memory and microSD card formatting;
SD upgrade −monitor software upgrade. Copy upgrade les to microSD card root folder, then insert
microSD card with upgrade les into monitor slot and select «SD upgrade» → «Yes». Wait until monitor will
be rebooted;
Exit − monitor settings exit.
Unlock time
Mode
Door 2
Cam 1
Cam 2
Exit
03s
Master
On
On
On
Record
Play
Backup
Format
SD upgrade
Exit
Off
7. Limited warranty
Manufacturer guarantees product normal functioning during the warranty period if the user keeps all safety
instructions described in that manual.
Warranty period is 12 months from the moment of the product purchasing (warranty period could be
extended up to 24 months or more, depending on the local regulations).
Warranty period allows user to make guarantee repair in cases when normal functioning of the product was
violated by the fault of manufacturer and the user haven’t oend transporting, installation and working
conditions.
This limited warranty does not cover any damage to the product that results from improper installation,
accident, abuse, misuse, natural disaster, insucient or excessive electrical supply, abnormal mechanical or
environmental conditions, or any unauthorized disassembly, repair or modication.
Warranty void in such cases:
• the product was damaged by the fault of the customer;
• the product wasn’t properly installed according reccomendations from the manual;
• the sticker on the backside of the product was broken;
• the product was not used for its intended function.
This limited warranty covers only repair, replacement, refund or credit for defective products, as provided
above. Manufacturer is not liable for, and does not cover under warranty, any damages or losses of any kind
whatsoever resulting from loss of, damage to, or corruption of, content or data or any costs associated with
determining the source of system problems or removing, servicing or installing products. This warranty
excludes third party software, connected equipment or stored data. Manufacturer is therefore not liable for
any losses or damage attributable to third party software, connected equipment or stored data.
In the event a product has been discontinued, manufacturer shall either repair the product, oer to replace
it with a comparable product or provide a refund at the lesser of the purchase price or the product’s current
value.
Repaired or replacement products will continue to be covered by this limited warranty for the remainder of
the original warranty term.
UNIQUE
DIRECT
SERIES