SMA SUNNY HIGHPOWER PEAK3 SHP 100-20 User manual

Operating manual
SUNNY HIGHPOWER PEAK3
SHP 100-21 / SHP 150-21 / SHP 172-21 / SHP 180-21
SHPxxx-21-BE-en-10 | Version 1.0ENGLISH

Legal Provisions SMA Solar Technology AG
Operating manualSHPxxx-21-BE-en-102
Legal Provisions
The information contained in these documents is the property of SMA Solar Technology AG. No part of this document
may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, be it electronic,
mechanical, photographic, magnetic or otherwise, without the prior written permission of SMA Solar Technology AG.
Internal reproduction used solely for the purpose of product evaluation or other proper use is allowed and does not
require prior approval.
SMA Solar Technology AG makes no representations or warranties, express or implied, with respect to this
documentation or any of the equipment and/or software it may describe, including (with no limitation) any implied
warranties of utility, merchantability, or fitness for any particular purpose. All such representations or warranties are
expressly disclaimed. Neither SMA Solar Technology AG nor its distributors or dealers shall be liable for any indirect,
incidental, or consequential damages under any circumstances.
The exclusion of implied warranties may not apply in all cases under some statutes, and thus the above exclusion may
not apply.
Specifications are subject to change without notice. Every attempt has been made to make this document complete,
accurate and up-to-date. Readers are cautioned, however, that product improvements and field usage experience may
cause SMA Solar Technology AG to make changes to these specifications without advance notice or per contract
provisions. SMA Solar Technology AG shall not be responsible for any damages, including indirect, incidental or
consequential damages, caused by reliance on the material presented, including, but not limited to, omissions,
typographical errors, arithmetical errors or listing errors in the content material.
SMA Warranty
You can download the current warranty conditions from the Internet at www.SMA-Solar.com.
Software licenses
The licenses for the installed software modules (open source) can be found in the user interface of the product.
Trademarks
All trademarks are recognized, even if not explicitly identified as such. Missing designations do not mean that a
product or brand is not a registered trademark.
SMA Solar Technology AG
Sonnenallee 1
34266 Niestetal
Germany
Phone [phone]
Fax [phone]
www.SMA.de
E-mail: [email protected]
Status: 2/20/2023
Copyright © 2023 SMA Solar Technology AG. All rights reserved.

Table of contents
SMA Solar Technology AG
Operating manual 3SHPxxx-21-BE-en-10
Table of contents
1 Information on this Document..................................................................................................... 6
1.1 Validity.............................................................................................................................................................. 6
1.2 Target Group ................................................................................................................................................... 6
1.3 Content and Structure of this Document......................................................................................................... 6
1.4 Levels of warning messages............................................................................................................................ 6
1.5 Symbols in the Document................................................................................................................................ 7
1.6 Typographical Elements in the Document ...................................................................................................... 7
1.7 Designations in the Document......................................................................................................................... 7
1.8 Additional Information..................................................................................................................................... 7
2 Safety ............................................................................................................................................ 9
2.1 Intended Use.................................................................................................................................................... 9
2.2 IMPORTANT SAFETY INSTRUCTIONS ......................................................................................................... 10
3 Scope of Delivery......................................................................................................................... 14
4 Additionally Required Materials and Equipment...................................................................... 16
5 Product Overview........................................................................................................................ 17
5.1 Product Description.......................................................................................................................................... 17
5.2 Symbols on the Product................................................................................................................................... 17
5.3 Interfaces and Functions.................................................................................................................................. 18
5.3.1 User Interface .................................................................................................................................................. 18
5.3.2 Smart Inverter Screen...................................................................................................................................... 19
5.3.3 SMA Speedwire.............................................................................................................................................. 19
5.3.4 Modbus ........................................................................................................................................................... 19
5.3.5 Grid Management Services ........................................................................................................................... 19
5.3.6 SMA Smart Connected................................................................................................................................... 19
5.3.7 SMA PUK2.0................................................................................................................................................... 19
5.4 LED Signals....................................................................................................................................................... 20
6 Mounting and Preparing the Connection .................................................................................. 21
6.1 Requirements for Mounting............................................................................................................................. 21
6.1.1 Requirements for the Mounting Location ....................................................................................................... 21
6.1.2 Requirements for the profile rails.................................................................................................................... 21
6.1.3 Permitted and prohibited mounting positions ................................................................................................ 22
6.1.4 Recommended clearances for mounting ....................................................................................................... 22
6.2 Connecting Plates Overview........................................................................................................................... 23
6.3 Center of gravity.............................................................................................................................................. 24
6.4 Preparing for mounting and connection......................................................................................................... 25
6.5 Mount the product........................................................................................................................................... 26
7 Electrical Connection.................................................................................................................... 30
7.1 Requirements for the electrical connection..................................................................................................... 30
7.1.1 Residual-current monitoring unit (RCMU) ...................................................................................................... 30
7.1.2 Overvoltage category..................................................................................................................................... 30
7.1.3 AC cable requirements ................................................................................................................................... 30
7.1.4 Network cable requirements .......................................................................................................................... 30
7.1.5 Laying plan for network cables ...................................................................................................................... 31
7.1.6 DC cable requirements ................................................................................................................................... 31
7.2 Overview of the Connection Area.................................................................................................................. 32
7.3 DC connection overview ................................................................................................................................. 33

Table of contents SMA Solar Technology AG
Operating manualSHPxxx-21-BE-en-104
7.4 Electrical connection procedure ..................................................................................................................... 33
7.5 Connecting the AC Cable............................................................................................................................... 34
7.6 Connecting the Network Cables .................................................................................................................... 35
7.7 Connecting the DC Cables ............................................................................................................................. 37
8 Commissioning ............................................................................................................................. 39
8.1 Procedure for commissioning in systems with System Manager................................................................... 39
8.2 Procedure for commissioning in systems without System Manager ............................................................. 39
8.3 Commissioning the Inverter ............................................................................................................................. 40
8.4 Logging into the user interface for the first time ............................................................................................. 41
8.5 Carry out the configuration using the installation assistant........................................................................... 42
8.6 Adopting the Configuration from a File.......................................................................................................... 43
8.7 Carry out the configuration manually............................................................................................................. 43
9 Operation ..................................................................................................................................... 44
9.1 Layout of the 'Configuring the Inverter' page................................................................................................. 44
9.2 Information for the use of the user interface................................................................................................... 45
9.3 Establishing a connection to the user interface.............................................................................................. 45
9.3.1 Establishing a Direct Connection via Ethernet............................................................................................... 45
9.3.2 Establishing a Connection via Ethernet in the local network........................................................................ 46
9.4 Logging Into the User Interface....................................................................................................................... 46
9.5 Logging out of the user interface .................................................................................................................... 47
9.6 Start Page Design of the User Interface ......................................................................................................... 48
9.7 Layout of the installation assistant................................................................................................................... 51
9.8 Starting the Installation Assistant..................................................................................................................... 51
9.9 Configuring the active power mode for systems with external setpoint....................................................... 52
9.10 Configuring the active power mode for systems with manual setpoint........................................................ 52
9.11 Changing parameters...................................................................................................................................... 53
9.12 Generating a product key for the first time .................................................................................................... 53
9.13 Generate new product key ............................................................................................................................. 54
9.14 Activate Service access ................................................................................................................................... 54
9.15 Deactivate Service access............................................................................................................................... 55
9.16 Dynamic power display (green LED).............................................................................................................. 55
9.17 Password .......................................................................................................................................................... 56
9.18 Country standard............................................................................................................................................. 56
9.19 Q on Demand 24/7 ....................................................................................................................................... 56
9.20 Saving the Configuration in a File .................................................................................................................. 57
9.21 Adopting a Configuration from a File ............................................................................................................ 58
9.22 Modbus function.............................................................................................................................................. 58
9.23 Automatic firmware update............................................................................................................................. 58
9.24 Updating Firmware with Update File via the User Interface......................................................................... 59
9.25 Updating firmware via the user interface....................................................................................................... 59
10 Disconnecting the product from voltage sources ...................................................................... 60
11 Cleaning........................................................................................................................................ 62
12 Troubleshooting ........................................................................................................................... 63
12.1 Event Messages............................................................................................................................................... 63
12.2 Restoring the password with product key ...................................................................................................... 75

Table of contents
SMA Solar Technology AG
Operating manual 5SHPxxx-21-BE-en-10
12.3 Restoring the password without product key ................................................................................................. 76
12.4 Calculating the insulation resistance .............................................................................................................. 77
12.5 Checking the PV System for Ground Faults.................................................................................................... 77
12.6 Replacing the Surge Arrester .......................................................................................................................... 79
12.7 Cleaning the Fans............................................................................................................................................ 79
12.8 Diagnostic function in the event of a defective Speedwire communication................................................. 81
12.9 Activating the Speedwire communication display......................................................................................... 81
12.10 Testing the Speedwire communication by using SMA Data Manager........................................................ 81
13 Decommissioning ......................................................................................................................... 83
13.1 Disconnecting product connections................................................................................................................ 83
13.2 Disassembling the product .............................................................................................................................. 85
14 Disposal ........................................................................................................................................ 88
15 Replacing the Product with a Replacement Device................................................................... 89
16 Technical Data.............................................................................................................................. 92
16.1 General Data................................................................................................................................................... 92
16.2 DC Input ........................................................................................................................................................... 93
16.3 AC Output........................................................................................................................................................ 93
16.4 Efficiency .......................................................................................................................................................... 95
16.5 Protective Devices............................................................................................................................................ 95
16.6 Climatic Conditions.......................................................................................................................................... 95
16.7 Torques............................................................................................................................................................. 95
17 Accessories ................................................................................................................................... 97
18 EU Declaration of Conformity..................................................................................................... 98
19 UK Declaration of Conformity .................................................................................................... 99
20 Contact .......................................................................................................................................... 100

1 Information on this Document SMA Solar Technology AG
Operating manualSHPxxx-21-BE-en-106
1 Information on this Document
1.1 Validity
This document is valid for:
• SHP 100-21 (Sunny Highpower PEAK3 100)
• SHP 150-21 (Sunny Highpower PEAK3 150)
• SHP 172-21 (Sunny Highpower PEAK3 172)
• SHP 180-21 (Sunny Highpower PEAK3 180)
1.2 Target Group
This document is intended for qualified persons and end users. Only qualified persons are allowed to perform the
activities marked in this document with a warning symbol and the caption "Qualifiedperson". Tasks that do not require
any particular qualification are not marked and can also be performed by end users. Qualified persons must have the
following skills:
• Knowledge of how to safely disconnect SMA inverters
• Knowledge of how an inverter works and is operated
• Training in how to deal with the dangers and risks associated with installing, repairing and using electrical devices
and installations
• Training in the installation and commissioning of electrical devices and installations
• Knowledge of all applicable laws, standards and directives
• Knowledge of and compliance with this document and all safety information
1.3 Content and Structure of this Document
This document describes the mounting, installation, commissioning, configuration, operation, troubleshooting and
decommissioning of the product as well as the operation of the product user interface.
You will find the latest version of this document and further information on the product in PDF format and as eManual
at www.SMA-Solar.com. You can also call up the eManual via the user interface of the product.
Illustrations in this document are reduced to the essential information and may deviate from the real product.
1.4 Levels of warning messages
The following levels of warning messages may occur when handling the product.
DANGER
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE
Indicates a situation which, if not avoided, can result in property damage.

1 Information on this Document
SMA Solar Technology AG
Operating manual 7SHPxxx-21-BE-en-10
1.5 Symbols in the Document
Icon Explanation
Information that is important for a specific topic or goal, but is not safety-relevant
☐
Indicates a requirement for meeting a specific goal
☑
Required result
Example
Sections describing activities to be performed by qualified persons only
1.6 Typographical Elements in the Document
Typographical element Use Example
bold • Messages
• Terminals
• Elements on a user interface
• Elements to be selected
• Elements to be entered
• Connect the insulated conductors
to the terminals X703:1 to
X703:6.
• Enter 10 in the field Minutes.
>• Connects several elements to be
selected
• Go to Settings > Date.
[Button]
[Key]
• Button or key to be clicked on or
pressed down
• Select [Enter].
# • Placeholder for variable components
(e.g., parameter names)
• Parameter WCtlHz.Hz#
1.7 Designations in the Document
Complete designation Designation in this document
SunnyHighpowerPEAK3 Sunny Highpower, inverter, product
1.8 Additional Information
For more information, please go to www.SMA-Solar.com.
Title and information content Type of information
"PUBLIC CYBER SECURITY - Guidelines for a Secure PV System Communication" Technical Information
"SMA GRID GUARD 10.0 - Grid Management Services via Inverter and System
Controller"
Technical Information
"Efficiency and Derating"
Efficiency and derating behavior of the SMA inverters
Technical Information
"Parameters and Measured Values"
Overview of all inverter operating parameters and their configuration options
Technical Information

1 Information on this Document SMA Solar Technology AG
Operating manualSHPxxx-21-BE-en-108
Title and information content Type of information
"SMA MODBUS"
Information on the SMA Modbus interface
Technical Information
"SUNSPEC MODBUS"
Information on the activation of the SunSpec Modbus interface and information
on the SunSpec Modbus profiles
Technical Information
"SMASPEEDWIRE FIELDBUS" Technical information
Important Requirements for Medium-Voltage Transformers
Requirements for Medium-Voltage Transformers
Technical Information

2 Safety
SMA Solar Technology AG
Operating manual 9SHPxxx-21-BE-en-10
2 Safety
2.1 Intended Use
The SunnyHighpower is a transformerless PVinverter. It converts the direct current from the PV modules into grid-
compliant three-phase current and feeds it into the utility grid via a separate transformer.
With the SunnyHighpower100 it is possible to feed the three-phase current directly into the low-voltage grid while
complying with the locally applicable connection requirements.
The product is intended for use in industrial environments.
The product complies with EN55011 of class A, group 1:
• a.c. mains power port: ≤ 20 kVA
• d.c. power port: > 75 kVA
• Electromagnetic radiation disturbance: ≤ 20 kVA
In accordance with EN55011, the product must only be operated at locations where the distance between the
product and third-party radio-communication installations is greater than 30m.
The product is not intended to be used in living areas and cannot provide protection of radio reception against
interference signals in such environments.
The product is suitable for operation in a chemically active environment in accordance with IEC60721-3-4 as per
Class4C2.
The product is suitable for indoor and outdoor use.
When used indoors, the ventilation system at the installation site must be able to dissipate the power loss that occurs.
The product must only be operated with PV modules of protection class II in accordance with IEC61730, application
class A. The PV modules must be compatible with this product.
The product may only be operated in connection with a suitable medium-voltage transformer. The low-voltage side
must be configured in a star formation and the neutral point must be grounded (for information about the requirements
of the medium-voltage transformer, consult the technical information "Important Requirements for Medium-Voltage
Transformers" under www.SMA-Solar.com).
The product is not equipped with an integrated transformer and therefore has no galvanic isolation. The product must
not be operated with PV modules whose outputs are grounded. This can cause the product to be destroyed. The
product may be operated with PV modules whose frame is grounded.
PV modules with a high capacity to ground must only be used if the coupling capacity of all PV modules does not
exceed 32μF (for information on how to determine the coupling capacity, see the Technical Information "Leading
Leakage Currents" at www.SMA-Solar.com).
All components must remain within their permitted operating ranges and their installation requirements at all times.
The product must only be used in countries for which it is approved or released by SMA Solar Technology AG and the
grid operator.
Use SMA products only in accordance with the information provided in the enclosed documentation and with the
locally applicable laws, regulations, standards and directives. Any other application may cause personal injury or
property damage.
Alterations to SMA products, e.g., changes or modifications, are only permitted with the express written permission of
and according to the instructions from SMA Solar Technology AG. Unauthorized alterations can be dangerous and
lead to personal injury. In addition, an unauthorized alteration will void guarantee and warranty claims and in most
cases terminate the operating license. SMA Solar Technology AG shall not be held liable for any damage caused by
such changes.
Any use of the product other than that described in the Intended Use section does not qualify as appropriate.
The enclosed documentation is an integral part of this product. Keep the documentation in a convenient, dry place for
future reference and observe all instructions contained therein.

2 Safety SMA Solar Technology AG
Operating manualSHPxxx-21-BE-en-1010
This document does not replace any regional, state, provincial, federal or national laws, regulations or standards that
apply to the installation, electrical safety and use of the product. SMA Solar Technology AG assumes no responsibility
for the compliance or non-compliance with such laws or codes in connection with the installation of the product.
The type label must remain permanently attached to the product.
2.2 IMPORTANT SAFETY INSTRUCTIONS
Keep the manual for future reference.
This section contains safety information that must be observed at all times when working.
The product has been designed and tested in accordance with international safety requirements. As with all electrical
or electronical devices, there are residual risks despite careful construction. To prevent personal injury and property
damage and to ensure long-term operation of the product, read this section carefully and observe all safety
information at all times.
DANGER
Danger to life due to electric shock when live components or DC cables are touched
When exposed to light, the PV modules generate high DC voltage which is present in the DC cables. Touching live
DC cables results in death or lethal injuries due to electric shock.
• Do not touch non-insulated parts or cables.
• Install external DC load-break switch (e.g., a PV junction box including a load-break switch) between the
inverter and PV array.
• Disconnect the PV array from the inverter via an external DC load-break switch (e.g. via a PV junction including
a load-break switch). Switch off and secure the DC load-break switch against reconnection.
• Disconnect the product from voltage sources and ensure it cannot be reconnected before working on the
device.
• Wear suitable personal protective equipment for all work on the product.
DANGER
Danger to life due to electric shock from touching an ungrounded PV module or array frame
Touching ungrounded PV modules or array frames results in death or lethal injuries due to electric shock.
• Connect and ground the frame of the PV modules, the array frame and the electrically conductive surfaces so
that there is continuous conduction. Observe the applicable local regulations.
DANGER
Danger to life due to electric shock when touching live system components in case of a ground
fault
If a ground fault occurs, parts of the system may still be live. Touching live parts and cables results in death or lethal
injuries due to electric shock.
• Disconnect the product from voltage sources and ensure it cannot be reconnected before working on the
device.
• Only touch the cables of the PV modules on their insulation.
• Do not touch any parts of the substructure or frame of the PV array.
• Do not connect PV strings with ground faults to the inverter.

2 Safety
SMA Solar Technology AG
Operating manual 11SHPxxx-21-BE-en-10
DANGER
Danger to life due to electric shock in case of overvoltages and if surge protection is missing
Overvoltages (e.g. in the event of a flash of lightning) can be further conducted into the building and to other
connected devices in the same network via the network cables or other data cables if there is no surge protection.
Touching live parts and cables results in death or lethal injuries due to electric shock.
• Ensure that all devices in the same network are integrated in the existing overvoltage protection.
• When laying the network cable outdoors, ensure that there is suitable surge protection at the network cable
transition from the product outdoors to the network inside the building.
• The Ethernet interface of the product is classified as "TNV-1" and offers protection against overvoltages of up to
1.5kV.
WARNING
Danger to life due to fire and explosion
In rare cases, an explosive gas mixture can be generated inside the product under fault conditions. In this state,
switching operations can cause a fire inside the product or explosion. Death or lethal injuries due to hot or flying
debris can result.
• In the event of a fault, do not perform any direct actions on the product.
• Ensure that unauthorized persons have no access to the product.
• Disconnect the PV array from the inverter via an external disconnection device. If there is no disconnecting
device present, wait until no more DC power is applied to the inverter.
• Disconnect the AC circuit breaker, or keep it disconnected in case it has already tripped, and secure it against
reconnection.
• Only perform work on the product (e.g., troubleshooting, repair work) when wearing personal protective
equipment for handling of hazardous substances (e.g., safety gloves, eye and face protection, respiratory
protection).
WARNING
Risk of injury due to toxic substances, gases and dusts.
In rare cases, damages to electronic components can result in the formation of toxic substances, gases or dusts
inside the product. Touching toxic substances and inhaling toxic gases and dusts can cause skin irritation, burns or
poisoning, trouble breathing and nausea.
• Only perform work on the product (e.g., troubleshooting, repair work) when wearing personal protective
equipment for handling of hazardous substances (e.g., safety gloves, eye and face protection, respiratory
protection).
• Ensure that unauthorized persons have no access to the product.
WARNING
Danger to life due to fire when failing to observe torque specifications on live bolted
connections
Failure to follow the specified torques reduces the ampacity of live bolted connections and the contact resistances
increase. This can cause components to overheat and catch fire. Death or lethal injuries can result.
• Ensure that live bolted connections are always tightened with the exact torque specified in this document.
• Only use suitable tools when working on the device.
• Avoid repeated tightening of live bolted connections as this may result in inadmissibly high torques.

2 Safety SMA Solar Technology AG
Operating manualSHPxxx-21-BE-en-1012
WARNING
Danger to life due to electric shock from destruction of the measuring device due to
overvoltage
Overvoltage can damage a measuring device and result in voltage being present in the enclosure of the measuring
device. Touching the live enclosure of the measuring device results in death or lethal injuries due to electric shock.
• Only use measuring devices with a measurement ranges designed for the maximum AC and DC voltage of the
inverter.
CAUTION
Risk of burns due to hot enclosure parts
Some parts of the enclosure can get hot during operation. Touching hot enclosure parts can result in burn injuries.
• During operation, do not touch any parts other than the enclosure lid of the inverter.
• Wait until the inverter has cooled down before touching the enclosure.
CAUTION
Risk of injury due to weight of product
Injuries may result if the product is lifted incorrectly or dropped while being transported or mounted.
• Transport and lift the product carefully. Take the weight of the product into account.
• Wear suitable personal protective equipment for all work on the product.
• Transport the product using the carrying handles or hoist. Take the weight of the product into account.
• Use all carrying handles provided during transport with carrying handles.
• Do not use the carrying handles as attachment points for hoist equipment (e.g. straps, ropes, chains). Insert eye
bolts into threads provided on top of the product to attach the hoist system.
NOTICE
Damage to the enclosure seal in subfreezing conditions
If you open the product when temperatures are below freezing, the enclosure seals can be damaged. Moisture can
penetrate the product and damage it.
• Only open the product if the ambient temperature is not below -5°C.
• If a layer of ice has formed on the enclosure seal when temperatures are below freezing, remove it prior to
opening the product (e.g. by melting the ice with warm air).
NOTICE
Damage to the product due to sand, dust and moisture ingress
Sand, dust and moisture penetration can damage the product and impair its functionality.
• Only open the product if the humidity is within the thresholds and the environment is free of sand and dust.
• Do not open the product during a dust storm or precipitation.
• Close tightly all enclosure openings.

2 Safety
SMA Solar Technology AG
Operating manual 13SHPxxx-21-BE-en-10
NOTICE
Damage to the inverter due to electrostatic discharge
Touching electronic components can cause damage to or destroy the inverter through electrostatic discharge.
• Ground yourself before touching any component.
NOTICE
Damage to the inverter due to switching operations on the transformer
If voltages are present in the inverter, switching operations on the transformer can lead to large fluctuations in the
voltage in the inverter. Large fluctuations in voltage can damage components in the inverter.
• Disconnect the inverter from voltage sources before performing any switching operations on the transformer.
NOTICE
Damage to the product due to cleaning agents
The use of cleaning agents may cause damage to the product and its components.
• Clean the product and all its components only with a cloth moistened with clear water.
The country data set must be set correctly.
If you select a country data set which is not valid for your country and purpose, it can cause a disturbance in the
PV system and lead to problems with the grid operator. When selecting the country data set, you must always
observe the locally applicable standards and directives as well as the properties of the PV system (e.g. PV system
size, grid-connection point).
• If you are not sure which standards and directives are valid for your country or purpose, contact the grid
operator.

3 Scope of Delivery SMA Solar Technology AG
Operating manualSHPxxx-21-BE-en-1014
3 Scope of Delivery
Check the scope of delivery for completeness and any externally visible damage. Contact your distributor if the scope
of delivery is incomplete or damaged.
H
LMNOP
K
FG
Q
J
I
AEDC
B
Figure 1: Components included in scope of delivery
Position Quantity Designation
A 1 Inverter
B 1 Mounting template
C 2 Mounting bracket
D 2 Button head screw M8x105
E 2 Button head screw M8x16
F 2 M10x40 combination hexagon head screw
G 2 Washer M10
H 4 Carry handle
I 2 Hex nut M10
J 2 M6x16 combined screw
K 4 Touch protection for DC connection
L 1 Connecting plate
M 3 Button head screw M8x70
N 1 Cable gland and counter nut M63x1.5

3 Scope of Delivery
SMA Solar Technology AG
Operating manual 15SHPxxx-21-BE-en-10
Position Quantity Designation
O 2 Cable gland and counter nut M40x1.5
P 1 M32x1.5 cable gland and counter nut with two-hole seal insert and two sealing
plugs
Q 1 Quick reference guide with registration data label on the rear side
The label contains the following information:
• PIC (Product Identification Code) identification key for registering the system
in SunnyPortal
• RID (Registration Identifier) registration ID for registering the system in
SunnyPortal

4 Additionally Required Materials and Equipment SMA Solar Technology AG
Operating manualSHPxxx-21-BE-en-1016
4 Additionally Required Materials and Equipment
Material or equipment Quantity Explanation
Profile rail (length: min. 770mm, depth:
40mm to 60mm, height: 50mm to 83mm)
2 For mounting the product
Terminal lugs (flange hole: M10) 2/4 For connecting the DC cables
Field-assembly RJ45 connector with metal en-
closure
1-2 Only required if the network cables are not equipped
with RJ45 plugs
Means of transport (e.g. pallet truck) 1 Used to transport packed product to mounting location
Eye bolt (M10) 2 Only required if the product is to be transported with a
hoist
Hoist 1 Only required if the product is to be transported with a
hoist
Utility knife 1 Used to unpack the product
Torx screwdriver (TX25) 1 Used to attach and remove transport handles
Torx screwdriver (TX40) 1 Used to attach the mounting brackets, to attach the prod-
uct to the mounting brackets, to attach the connection
plate to the product, to connect additional grounding
Allen key (AF8) 1 To attach and remove the enclosure lid and to connect
the AC cables
Allen key (AF16) 1 To connect the DC cables
Measuring device with a measuring range
designed for the maximum AC and DC volt-
age of the product
1 For verifying that no voltage is present
Current clamp 1 For verifying that no voltage is present
Press tool 1 Used to attach terminal lugs to DC cables
Clean cloth 1 Used to clean terminal lugs
Ethanol cleaning agent 1 Used to clean terminal lugs
Brush 1 Used to clean aluminum conductor (only necessary if ca-
ble is made of aluminum)
Protective grease 1 Used to apply to aluminum conductor (only necessary if
cable is made of aluminum)

5 Product Overview
SMA Solar Technology AG
Operating manual 17SHPxxx-21-BE-en-10
5 Product Overview
5.1 Product Description
Figure 2: Design of the product
Position Designation
A LEDs
The LEDs indicate the operating state of the product.
B Cover
C Type label
The type label clearly identifies the product. The type label must remain permanently at-
tached to the product. You will find the following information on the type lable:
• Device type (Model)
• Serial number (Serial No. or S/N)
• Date of manufacture
• Device-specific characteristics
5.2 Symbols on the Product
Icon Explanation
Beware of a danger zone
This symbol indicates that the product must be additionally grounded if additional grounding
or equipotential bonding is required at the installation site.
Beware of electrical voltage
The product operates at high voltages.

5 Product Overview SMA Solar Technology AG
Operating manualSHPxxx-21-BE-en-1018
Icon Explanation
Beware of hot surface
The product can get hot during operation.
Observe the documentations
Observe all documentations supplied with the product.
Inverter
Together with the green LED, this symbol indicates the operating state of the inverter.
Observe the documentations
Together with the red LED, this symbol indicates an error.
Data transmission
Together with the blue LED, this symbol indicates the status of the network connection.
Three-phase alternating current without neutral conductor
Direct current
The product has no galvanic isolation.
WEEE designation
Do not dispose of the product together with the household waste but in accordance with the
disposal regulations for electronic waste applicable at the installation site.
The product is suitable for outdoor installation.
Degree of protectionIP65
The product is protected against the penetration of dust and water that is directed as a jet
against the enclosure from all directions.
CE marking
The product complies with the requirements of the applicable EU directives.
UKCA marking
The product complies with the regulations of the applicable laws of England, Wales and
Scotland.
RoHS
RoHS labeling
The product complies with the requirements of the applicable EU directives.
5.3 Interfaces and Functions
5.3.1 User Interface
The product is equipped as standard with an integrated webserver, which provides a user interface for configuring and
monitoring the product.

5 Product Overview
SMA Solar Technology AG
Operating manual 19SHPxxx-21-BE-en-10
Once the connection has been established to the smart device, use a terminal (e.g. smartphone, tablet or laptop) to
connect to the product's user interface using a web browser.
5.3.2 Smart Inverter Screen
The Smart Inverter Screen enables you to view the status display and to display the current power and consumption on
the user interface login page. This gives you an overview of the most important product data without having to log into
the user interface.
The Smart Inverter Screen is deactivated by default. The Smart Inverter Screen can be activated via the user interface
once the product has been commissioned.
5.3.3 SMASpeedwire
The product is equipped with SMASpeedwire as standard. SMASpeedwire is a type of communication based on the
Ethernet standard. SMASpeedwire is designed for a data transfer rate of 100Mbps and enables optimum
communication between Speedwire devices within systems.
The products supports the encrypted system communication with SMA Speedwire Encrypted Communication. In order
to be able to use the Speedwire encryption in the system, all Speedwire devices, except for the energy meter (e.g.
SMAEnergyMeter) must support the function SMASpeedwireEncryptedCommunication.
5.3.4 Modbus
The product is equipped with a Modbus interface. The Modbus interface is deactivated by default and must be
configured as needed.
The Modbus interface of the supported SMA products is designed for industrial use – via SCADA systems, for example
– and has the following tasks:
• Remote query of measured values
• Remote setting of operating parameters
• Setpoint specifications for system control
5.3.5 Grid Management Services
The product is equipped with service functions for grid management.
Depending on the requirements of the grid operator, you can activate and configure the functions (e.g. active power
limitation) via operating parameters.
5.3.6 SMA Smart Connected
SMA Smart Connected is the free monitoring of the product via the SMA SunnyPortal. Thanks to SMA Smart
Connected, the operator and qualified person will be informed automatically and proactively about product events
that occur.
SMA Smart Connected is activated during registration in SunnyPortal. In order to use SMA Smart Connected, it is
necessary that the product is permanently connected to SunnyPortal and the data of the operator and qualified
person is stored in SunnyPortal and up-to-date.
5.3.7 SMA PUK2.0
SMA PUK2.0 replaces for products with firmware version ≥ 4.00.00.R the previous procedure for logging in to the
user interface if you have forgotten the password for your product. Whether your product supports PUK2.0 is shown
on the login page of the user interface via the information button.
To improve security for your product, SMA Solar Technology AG recommends generating a product key. With the
product key, the product can be unlocked directly on the user interface and does not require a chargeable order of a
PUK via SMA Solar Technology AG. If you have lost the product key, you can generate a new one by physically
accessing the product.

5 Product Overview SMA Solar Technology AG
Operating manualSHPxxx-21-BE-en-1020
5.4 LED Signals
The LEDs indicate the operating state of the product.
LED signal Explanation
The green LED is flashing (2s on
and 2s off)
Waiting for feed-in conditions
The conditions for feed-in operation are not yet met. As soon as the conditions
are met, the product will start feed-in operation.
The green LED flashes quickly Update of central processing unit
The central processing unit of the product is being updated.
The green LED is glowing Feed-in operation
The product feeds in with a power of at least 90%.
The green LED is pulsing Feed-in operation
The product is equipped with a dynamic power display via the green LED. De-
pending on the power, the green LED pulses fast or slow. If necessary, you can
switch off the dynamic power display via the green LED.
The green LED is off The product is not feeding into the utility grid.
The red LED is glowing Event occurred
If an event occurs, a distinct event message and the corresponding event number
will be displayed in addition on the product user interface or in the communica-
tion product (e.g. SMADataManager).
The blue LED flashes slowly for
approx. 1minute
Communication connection is being established
The product is establishing a connection to a local network or is establishing a di-
rect connection to a smart device via Ethernet (e.g. smartphone, tablet or laptop).
The blue LED is glowing Communication active
There is an active connection with a local network or there is a direct connection
via Ethernet with a smart end device (e.g. smartphone, tablet or laptop).
Also see:
• Dynamic power display (green LED)⇒page55