SMART-AVI XTREEM-WALL User manual

1
Made in U.S.A. www.SmartAVI.com 1-800-AVI-2131
XTREEM-WALL
User Manual
4K INPUT MULTI-FORMAT 2X2 VIDEO WALL CONTROLLER

2
TABLE OF CONTENTS
WHAT'S IN THE BOX? 2
INTRODUCTION 3
FEATURES 3
APPLICATIONS 3
TECHNICAL SPECIFICATIONS 4
HARDWARE INSTALLATION 5-6
FRONT PANEL CONTROL 7
IR REMOTE CONTROL 8
CONTROL VIA NETWORK 9-14
PRE-DEFINED DISPLAY MODES 15
LIMITED WARRANTY STATEMENT 16
Figure 2-1
WHAT’S IN THE BOX?
PART NO. QTY DESCRIPTION
XTRW-S 1 4K IN-HD OUT HDMI/DP/DVI-I Video Wall Controller
RMT-XW 1 IR Remote Control
SM-EYE3 1 IR Receiver
PS12VDC3.33A 1 Power Adapter
1 Quick Start Guide
Brackets for mounting this device in a standard 19” rack can be ordered from SmartAVI.

3
INTRODUCTION
The XTREEM-WALL is Smart-AVI’s easiest and most effective solution for building creatively configured
video walls. With multi-format inputs for video resolutions up to 4K (3840x2160 @ 30Hz), the XTREEM-
WALL sends multi-screen imagery to four connected HDMI displays in 1080p Full HD (1920x1080 @
60Hz) output.
Best of all, the XTREEM-WALL is highly compatible with the most popular displays on the market, and fea-
tures a wide variety of video wall modes.
FEATURES
 INPUT: (1) DP, (1) DVI-I Full HD Input, (1) HDMI 4K Input
 OUTPUT: (4) 1080p HDMI, (1) HDMI Local Loop
 Input up to 4K (3840x2160 @ 30Hz)
 Output up to 1080p (1920x1080 @ 60Hz)
 Creative configuration modes, including: Full Video Wall | Clone | PIP | POP | Flip
 Supports VGA & Y/Pb/Pr (With DVI-I Adapter)
 Supports IR remote control
 Control over web console
 Plug-and-Play ready
 Front Panel Buttons: XTREEM-WALL features a button control panel for switching between sources
and accessing preset configurations.
 Web Console: Control everything from source resolution and aspect ratios to creative display modes
from anywhere in the world over the Internet with SmartAVI’s easy-to-use web console for the XTREEM
-WALL.
APPLICATIONS
 Corporate or Educational Presentations
 Airport Installations
 Wall Displays
 Digital Signage
 Dealer Rooms
 Control Rooms
 Shopping Centers
 Security
 Point-of-Sale
 Entertainment Venues
 Corporate Lobbies
 Restaurants

4
TECHNICAL SPECIFICATIONS
VIDEO (and AUDIO)
Video Format DP, DVI-I, HDMI
Video Input (1) DP; (1) DVI-I; (1) HDMI, VGA & Y/Pb/Pr support w/ DVI-I adaptor
Video Output (4) HDMI 2.0 (1) HDMI Loopback
Input Resolution Up to 4K (3840x2160 @ 30Hz)
Output Resolution Up to 1080 (1920x1080 @ 60Hz)
Audio Input/Output HDMI Digital Audio
Compliance HDCP Compliant
CONTROL
Front Panel Buttons
TCP/IP Web Console
IR Remote Control RC-100 Infrared Remote Control with IR-EYE3 receiver
OTHER
RS-232 DB9 Female, 115200 bps, N, 8 1, No flow control (For firmware updates only)
Power Adapter 12VDC 3.33A
Weight 6.95 lbs.
Dimensions 17”W X 10.8”D X 1.9”H
Working Temp. 32 to 122°F (0 to 50 °C )
Working Humidity Up to 85% RH (no condensation)
Storage Temp. -4 to 149 °F (-20 to 65 °C )
Storage Humidity Up to 90% RH (no condensation)

5
HARDWARE INSTALLATION
1. Make sure the XTREEM-WALL is turned off.
2. Connect up to 3 inputs or sources. (1 DP, 1 HDMI, 1 DVI)
3. Connect up to 4 displays to the HDMI OUTPUT ports on the XTREEM-WALL. See Figure 5-2 for display
locations.
4. Optionally connect a display to the HDMI OUT (Loopback) port.
5. Optionally connect the IR receiver to the IR input jack on the back of the XTREEM-WALL.
6. Optionally connect a network with a cat5/6 cable to the RJ45 LAN connector on the back of the
XTREEM-WALL.
7. Turn on the XTREEM-WALL.
8. Wait for the unit to initialize.
NOTE: The RS-232 port on the back of the XTREEM-WALL is for firmware updates only.
Figure 5-1
Figure 5-3
Figure 5-2
Connect HDMI Output port 1 to the upper left display.
Connect HDMI Output port 2 to the upper right display.
Connect HDMI Output port 3 to the lower left display.
Connect HDMI Output port 4 to the lower right display.

6
HARDWARE INSTALLATION (Continued)
Figure 6-1 below shows a configuration using an HDMI source to display a video wall plus an additional
display using the HDMI Out loopback port.
Figure 6-1
Figure 6-2 below shows a configuration using a DVI input for the video wall while using the HDMI loop-
back ports to connect an additional display.
Figure 6-2

7
VIDEO WALL MODE
An Image can be displayed
across four HD screens
2X2.
Figure 6-1
CLONE MODE
The image can be dis-
played on each display in-
dividually.
Figure 6-2
FRONT PANEL CONTROL
To switch between listed sources, press:
1. DVI
2. HDMI
3. DisplayPort
To switch to Video Wall mode, press the WALL button.
To switch to Clone mode, press the CLONE button.
Loading predefined display modes. First press the MACRO button. Then press:
1 =
2 =
3 =
4 =
5 = Standard video wall. Same as WALL button.

8
IR REMOTE CONTROL
BUTTON DESCRIPTION
HDMI Select HDMI input port
DVI Select DVI input port
DP Select DP input port
Info Current settings will display
MENU Turns on OSD (On Screen Display)
Back Moves back 1 menu
Exit Exit OSD
▲OSD (On Screen Display) Navigation
▼OSD (On Screen Display) Navigation
◄OSD (On Screen Display) Navigation
►OSD (On Screen Display) Navigation
OK Executes selection or opens menu
OTH Opens selected Menu
OSD
TIME OUT Sets time before OSD turns off
VIDEO
WALL Opens OSD for output settings

9
CONTROL VIA NETWORK
XTREEM-WALL TCP/IP control is a feature that allows mode switching and other configurations to be con-
trolled remotely via HTTP. Manage your XTREEM-WALL with ease from anywhere in the world.
First you must find the IP address for the
XTREEM-WALL . Finder.exe (Smart IP-
Finder) is conveniently available on our
website; please visit www.smartavi.com/
helpful-links.html for this and our full list
of compatible third-party software.
Download and execute the IP address
Finder software for your product. The
XTREEM-WALL and its IP address should
appear in the display as shown in Figure
9-1.
Figure 9-1
Enter the IP address into a web browser of your choice. You should see the XTREEM-WALL LOG-IN page as
shown in Figure 9-2. The default username is ADMIN and the default password is PASS.
Figure 9-2

10
CONTROL VIA NETWORK (Continued)
Click the “XTREEM-Wall” tab in the
top row and then click the “Current”
tab in the second row to see the cur-
rent status of the XTREEM-WALL.
Click the “XTREEM-Wall” tab in the
top row and then click the “Video
Wall” tab in the second row. Here you
can select the source port for your
video wall display.
Click the “XTREEM-Wall” tab in the
top row and then click the “Video Wall
Clone” tab in the second row. Here
you can select the source port for
your video wall display.