SMART-AVI HDX-XT User manual

HDX-XT
User Manual
www.smartavi.com |Tel: (800)AVI-213 | [phone] | 2455WCheyenneAve, Suite 112 | North LasVegas, NV89032
4K Video and USB 2.0 KVM Extender

Table of Contents
TABLE OF CONTENTS / WHAT'S IN THE BOX? 2
INTRODUCTION 3
FEATURES 3
APPLICATIONS 3
HARDWARE INSTALLATION 4
FRONT PANEL CONTROL (Transmier) 5
REAR PANEL CONTROL (Transmier) 6
FRONT PANEL CONTROL (Receiver) 7
REAR PANEL CONTROL (Receiver) 8
TECHNICAL SPECIFICATIONS 9
LIMITED WARRANTY STATEMENT 10
WHATS IN THE BOX?
Model Number Descripon
HDX-XT-S (1) HDX-XT 4K Extender with USB 2.0 Transmier and
Receiver Unit(s); Quickstart Guide
PS12VDC1A (2) Power Supply DC 12V@1A
NOTICE:
The informaon contained in this document is subject to change without noce. Smart-AVI makes no warranty of any kind with regard to this material,
including but not limited to, implied warranes of merchantability and tness for any parcular purpose. Smart-AVI will not be liable for errors contained
herein or for incidental or consequenal damages in connecon with the furnishing, performance or use of this material. No part of this document may be
photocopied, reproduced or translated into another language without prior wrien consent from Smart-AVI.

Thank you for purchasing this product. For opmum performance and safety, please read the instruc-
on carefully before connecng, operang or adjusng this product. Please keep the manual for future
reference.
The HDMI USB KVM (Keyboard, Video, Mouse) Extender is a tool which can extend your HDMI signal
over 328./100meters to a compable display. It is designed to convert HDMI signal to standard, ex-
tended signal which can be transmied by CAT5e/CAT6/CAT7 cable. It also supports Transfer Bidirec-
onal Infrared control signal and RS232 control signal. The HDX-XT also supports the connecon of a
USB host and 2 USB device ports.
• Zero pixel loss with TMDS signal correcon
• Fully compliant with HDMI 1.4, and compable with HDMI 2.0 (4K2K@60Hz with YCbCr 4:2:0 ).
• HDCP2.2 and DVI compable.
• Supports Extender 2.0 specicaon over a single CAT5e/6/7 cable up to 100m/328.
• Supports pass-through of HD audio formats: LPCM2/5.1/7.1 CH, Dolby Digital, DTS, Dolby TrueHD,
• DTS-HD Master Audio and more.
• POE funcon support, either TX or RX powered 24V@1A,
• Full HD support: 1080p@60Hz@24/36/48bit/pixels.
• Supports USB 2.0 control.
• Supports external Bi-Direconal SPDIF IN/OUT and available for mulchannel audio.
• Supports stereo audio with PCM 2CH.
• Transfer Bidireconal Infrared control signal together with the HDMI signal.
• Transfer Bidireconal RS232 control signal together with the HDMI signal.
fEATURES:
introduction

1. Disconnect power from all devices involved with the installaon.
2. Connect the display, keyboard, mouse, audio and USB devices to the ports idened
for each item on the HDX-XT Receiver Unit.
3. Connect the Computer’s Display output and USB port to the ports idened for each
item on the HDX-XT Transmier Unit.
4. Connect the HDX-XT Transmier Unit to the HDX-XT Receiver Unit with a CAT5/5e/6
cable. For the best quality video use a single CAT5/5e/6 cable to connect the
HDX-XT Transmier to the Receiver. The HDX-XT is not designed to work
with Routers, Switches or Hubs.
5. Power on the devices connected to the HDX-XT Receiver Unit.
6. Connect the power supplies provided to the HDX-XT Transmier and Receiver and
connect them both to power.
7. Power on the Computer.
If needed you can force the HDX-XT to re-learn the Monitors EDID sengs with the
following hot-key combinaon. Press the Ctrl key twice, press the e key, then press the
Enter key. This will cause the USB light on the front of the HDX-XT Transmier Unit to
blink rapidly for 1 second, indicang the EDID sengs have been re-learned.
HARDWARE INSTALLATION
Connecting more USB devices:
If additional devices needed to be connected,
connect a USB hub to the USB port of the receiver.

Plug in the desired output and inputs, then power on the unit. Press SELECT to alternate between inputs
that will be displayed via the output. Press SELECT once more to switch the output.
tRANSMITTER FRONT PANEL CONTROL
1. Indicator LED:
Power LED: Illuminates when power has been supplied to the unit.
Link LED: The connecon status indicang lamp.
Illuminate: The Transmier and Receiver have good connecons.
Flashing: The Transmier and Receiver have poor connecons.
Dark: The Transmier and Receiver have no connecons.
HDCP LED: The HDCP status indicang lamp.
Illuminate: The HDMI signal with HDCP.
Flashing: The HDMI signal without HDCP.
Dark: No HDMI signal.
FW LED: Light is ashing on behalf of the unit work normally
2. IR IN: Channel 1 IR Receiver. Connect with Wideband IR Rx.
3. IR OUT: Channel 2 IR Transmier. Connect with Wideband IR Tx.
4. RS232 TX/RX: Connect to a PC or Laptop with 3-pin Relay cable for the transmission of
RS-232 commands.
5. AUDIO IN: Connect to a PC or Laptop stereo output port via 3.5mm audio cable.
6. USB-D: Connect to USB peripheral devices such as printer, keyboard, mouse, ash drive, etc.
7. USB-H: Connect from PC or Laptop for data transmit to or control from the Receiver’s USB-D slots.
8. USB-H/USB-D SELECT: Select USB host or USB device.

Plug in the desired output and inputs, then power on the unit. Press SELECT to alternate between inputs
that will be displayed via the output. Press SELECT once more to switch the output.
TRANSMITTER REAR CONTROLS
9. UPDATE: Reserved for manufacturer use only.
10. Extender OUT: Standard Extender signal output port. Connect Extender receiver with a
Cat5e/6/7 cable.
11. HDMI IN: This slot is where you connect the HDMI source.
12. SPDIF IN (Opcal in): Connect to audio source equipment such as DVD or Blu-ray player for
audio signal sending to Receiver’s SPDIF OUT (Opcal out).
13. SPDIF OUT (Opcal out): Connect to speaker with coaxial input for audio signal output from
Receiver’s SPDIF IN (Opcal in).
14. LAN: This slot provide Internet signal from receiver or to receiver.
15. DC IN: Plug the 24V DC power supply into the unit.
HDX-XT (TX) Front HDX-XT (TX) Rear

Plug in the desired output and inputs, then power on the unit. Press SELECT to alternate between inputs
that will be displayed via the output. Press SELECT once more to switch the output.
Receiver FRONT PANEL CONTROL
1. Indicator LED:
Power LED: illuminates when power has been supplied to the unit.
Link LED: The connecon status indicang lamp.
Illuminate: The Transmier and Receiver have good connecons.
Flashing: The Transmier and Receiver have poor connecons.
Dark: The Transmier and Receiver has no connecons.
HDCP LED: The HDCP status indicang lamp.
Illuminate: The HDMI signal with HDCP.
Flashing: The HDMI signal without HDCP.
Dark: No HDMI signal.
FW LED: Light is ashing on behalf of the unit work normally
2. IR IN: Chanel 1 IR Receiver. Connect with Wideband IR Rx.
3. IR OUT: Chanel 2 IR Transmier. Connect with Wideband IR Tx.
4. RS232 TX/RX: Connect to the devices that are to be controlled via 3-pin Relay cable by
RS-232 commands.
5. AUDIO OUT: Connect to speaker via 3.5mm audio cable.
6. USB-D: Connect to USB peripheral devices such as printer, keyboard, mouse, ash drive, etc.
7. USB-H: Connect from PC or Laptop for data transmit to or control from the Receiver’s USB-D slots.
8. USB-H/USB-D SELECT: Select USB host or USB device.

Plug in the desired output and inputs, then power on the unit. Press SELECT to alternate between inputs
that will be displayed via the output. Press SELECT once more to switch the output.
receiver REAR CONTROL
9. UPDATE: Reserved for manufacturer use only.
10. Extender IN: Standard Extender signal output port. Connect Extender Transmier with a
Cat5e/6/7 cable.
11. HDMI OUT: This slot is where you connect the a HDMI equipped TV/monitor.
12. SPDIF IN (Opcal in): Connect to audio source equipment such as DVD or Blu-ray player for audio
signal sending to Transmier’s SPDIF OUT(Opcal out).
13. SPDIF OUT (Opcal out): Connect to speaker with coaxial input for audio signal output from
Transmier’s SPDIF IN (Opcal in).
14. LAN: This slot provide Internet signal from receiver or to receiver.
15. DC IN: Plug the 24V DC power supply into the unit.
HDX-XT (RX) Front HDX-XT (RX) Rear

technical specifications:
VIDEO
Format HDMI
Input Interface (RX) (1) IR In, (1) Opcal (Spdif In), (1) Extender In, (1) USB-H
Output Interface (RX) (1) HDMI, (1) LAN, (2) USB, (1) IR Out, (1) Audio Out, (1) RS-232, (1) Opcal (Spdif out)
Input Interface (TX) (1) HDMI, (1) LAN, (1) USB-H, (1) IR-IN, (1) RS-232, (1) Opcal (Spdif in), (1) Audio In
Output Interface (TX) (1) IR Out, (1) Opcal (Spdif out), (1) Extender Out, (2) USB-D
Resoluon 480p, 720p, 1080i, 1080p/60Hz, 4K/30Hz
Max Output Distance 1080p@60 100m (328/100m) [CAT5/5e/6] 4K2K (4:2:0 8bit) 80m (264) [CAT5/5e/6]
Equalizaton Auto
Input TMDS Signal 1.2 Volts [peak-to-peak]
Input DDC Signal 5 Volts [peak-to-peak, TTL]
Video Bandwidth Single-Link 340 MHz (10.2 Gbps)
AUDIO
Format HDMI
Input Interface 3.5 mm Jack Socket (Female)
Output Interface 3.5 mm Jack Socket (Female)
USB
Format USB 2.0
Input Interface 1.1 with full emulaon
RS-232
Format Full duplex TXD, RXD signal
SYSTEM
Interface RJ45
Cable Requirements CAT5/5e/6
Maximum Length 328 . (100m)
OTHER
Approvals UL, CE, ROHS Compliant
Power DC 12V 1A
Operang Temperature 32 - 104°F ( 0-40°C)
Storage Temperature -4 - 140°F (-20 - 60°C)
Humidity Up to 95%
Dimensions 160 (W) X 97 (D) X 28 (H)
Weight 450g/TX, 450g/RX

LIMITED WARRANTY STATEMENT
A. Extent of limited warranty
Smart-AVI Technologies, Inc. warrants to the end-user customers that the Smart-AVI product specied
above will be free from defects in materials and workmanship for the duraon of 1 year, which duraon
begins on the date of purchase by the customer. Customer is responsible for maintaining proof of date of
purchase. Smart-AVI limited warranty covers only those defects which arise as a result of normal use of
the product, and do not apply to any:
a. Improper or inadequate maintenance or modicaons
b. Operaons outside product specicaons
c. Mechanical abuse and exposure to severe condions
If Smart-AVI receives, during applicable warranty period, a noce of defect, Smart-AVI will at its discreon
replace or repair defecve product. If Smart-AVI is unable to replace or repair defecve product covered
by the Smart-AVI warranty within reasonable period of me, Smart-AVI shall refund the cost of the prod-
uct. Smart-AVI shall have no obligaon to repair, replace or refund unit unl customer returns defecve
product to Smart-AVI. Any replacement product could be new or like new, provided that it has funconal-
ity at least equal to that of the product being replaced. Smart-AVI limited warranty is valid in any country
where the covered product is distributed by Smart-AVI.
B. Limitaons of warranty
To the extant allowed by local law, neither Smart-AVI nor its third party suppliers make any other warranty
or condion of any kind whether expressed or implied with respect to the Smart-AVI product, and spe-
cically disclaim implied warranes or condions of merchantability, sasfactory quality, and tnessfor a
parcular purpose.
C. Limitaons of liability
To the extent allowed by local law the remedies provided in this warranty statement are the customers
sole and exclusive remedies. To the extant allowed by local law, except for the obligaons specically set
forth in this warranty statement, in no event will Smart-AVI or its third party suppliers be liable for direct,
indirect, special, incidental, or consequenal damages whether based on contract, tort or any other legal
theory and whether advised of the possibility of such damages.
D. Local law
To the extent that this warranty statement is inconsistent with local law, this warranty statement shall be
considered modied to be consistent with the law.
www.smartavi.com
Tel: (800)AVI-2131 [phone]
2455WCheyenneAve, Suite 112
North LasVegas, NV89032