smart home SH-U6 User manual

MODEL: SH - U6
by Bkav

www.smarthome.bkav.com
UGU6/V1.0/0914
893604393UGU6
Mfr Code:
Copyright © 2014 Bkav SmartHome Co., Ltd. All rights reserved.

USER GUIDE
IN-WALL URINAL SENSOR FLUSH VALVE
SH - U6
Bkav SmartHome technology company limited

Usage instruction
Electric shock may cause injuries or threats to life. Before
installing, repairing or cleaning the device, you should check
whether the device’s power is disconnected.
This work should be done by technicians or Customer
Contact Center to avoid electric related accidents.
Environmental regulations must be complied when discard-
ing or recycling the device or its wrapping.
Thank you for choosing in-wall urinal sensor flush valve SH - U6 of Bkav
SmartHome. By selecting Bkav SmartHome’s products, you will get the best
warranty service and installation support from our technicians.
This document gives useful information during installation and usage time.
You should read and keep the manual carefully in case of need.
Warning
Copyright © 2014 Bkav SmartHome Co., Ltd. All rights reserved.
In-wall urinal sensor flush valve SH - U6 is the product of Bkav SmartHome
and has been registered regarding design, utility solutions and quality certifi-
cation. All violations such as copies of design and product idea are subject to
the current copyright law of the Socialist Republic of Vietnam.
1

Content
2
Usage notice
Safety instruction
Introduction
General introduction
Product package
Accessories
Device’s components
Sensing range
Specifications
Operating mode settings
How to set up operating mode
Operating mode settings
Installation
Step 1: Assemble the valve
Step 2: Assemble the valve with water pipe
Step 3: Assemble a protective frame on the receptacle box
Step 4: Install the receptacle box
1
4
5
5
5
6
7
8
9
11
11
11
12
12
13
14
15

3
16
17
18
19
20
22
22
23
24
26
29
Step 5: Disassemble the protective frame from the receptacle box
Step 6: Insert a battery box into the receptacle box
Step 7: Install a bend pipe
Step 8: Assemble the mounting frame with the receptacle box
Step 9: Assemble an aluminum frame with the mounting frame
Usage and maintenance
Usage steps
Maintenance during use
Operation cycle
Problem and Solution
Contact

Do not leave the device in high-temperature environment.
Do not disassemble the device if not necessary.
Do not clean the device with corrosive chemicals.
Safety instruction
Warning
Do not use voltage which is different from the one stated in the
device’s specifications.
Disconnect the device’s power prior to any installation, disassembly
or repair.
Safety instruction should be complied during the device usage.
4

General introduction
Product package
User guide (book) SH - U6
Introduction
The in-wall urinal sensor valve uses pyroelectric infrared radial sensor
technology. When users are in the sensor area, the device will automatically
flush water to clean the urinal. The product’s smart feature brings comfort,
power saving and absolute safety to its users.
With modern and luxurious design, the device is suitable for hotels, business
centers, airports, stations, public restrooms, etc.
5
MODEL: SH - U6
by Bka v

Accessories
Straight conduit
connector
Solenoid valve Flexible conduit
connector
Bend pipe Screw cover
M2x4 Screw M4x12 Screw
Protective frame
6

Device’s components
Infrared sensing component: transmits and receives infrared signal from
users’ response in the sensor area, then notifying the central processor.
Indicator light: has the notification function, the light is on when detecting
a user in the sensor area.
Infrared sensing component
Indicator light
7

Sensing range
Range of receiving reflected signal Range of transmitting infrared signal
500 mm
250 mm
350 mm
15º
The sensing range can be adjusted from 40 cm to 60 cm
based on installation conditions and customers’ needs.
Note
8

Specifications
100-240V 50/60HzVoltage
Battery
Battery lifespan 2 years with 100 times/day(*)
Water consumption 2 - 4 liters/each time
Sensing range 60 cm max
Water supply pressure 0.7 - 7.6 Kgf/cm²
Configured wet flush 2 - 5 seconds
Configured clean flush 6 - 12 seconds
Automatic wet flush 12 hours
Water temperature 5ºC - 50ºC
Used water Clean water without residue
Dimensions (L x W x H)
Operating temperature 60ºC max
Weight 1.1 kg
110 x 130 x 132 mm
9
6V , 4AA

(*) The device’s lifespan can be longer or shorter depending
on usage conditions and environment. The above durability is
tested in standard conditions.
Note
10

Operating mode settings
The urinal sensor valve is appropriate to all male urinals and usage
conditions, the device can be adjusted flush time and sensing range.
How to set up operating mode
Operating mode settings
Wet flush:
Clean flush:
2 seconds
6 seconds
Default mode
Wet flush:
Clean flush:
5 seconds
10 seconds
Wet flush:
Clean flush:
3 seconds
8 seconds
Wet flush:
Clean flush:
3 seconds
8 seconds
Wet flush:
Clean flush:
6 seconds
12 seconds
11

1a: Assemble a straight conduit connector with the solenoid valve.
1b: Assemble a flexible conduit connector with the solenoid valve.
Installation
Step 1: Assemble the valve as shown in figure (1)
12
1
Straight conduit connector
Solenoid valve
Flexible conduit connector
1a
1b
Filter

Note: The water pipe must be clean prior to assembly.
Flexible conduit connector protrudes from the wall surface from 10 - 17 mm.
Step 2: Assemble the valve with a water pipe as shown in figure (2)
13
2
10 - 17 mm
90 - 110 cm
150 mm

Step 3: Assemble a protective frame on the receptacle box
14
3
Protective frame
Receptacle box

After installing the receptacle box, remove the protective frame when
mortar is dry.
Step 4: Install the receptacle box as shown in figure (4)
Protective frame
Receptacle box
15
4

Step 5: Disassemble the protective frame from the receptacle box as
shown in figure (5)
16
5
Protective frame Receptacle box

Step 6: Insert a battery box into the receptacle box as shown in figure (6)
17
6
Battery box