Smart power Venus Series User manual

What's in the box: • Battery
• Instructions
Turn the UPS upside down
Unscrew all 4 screws located at the base of the UPS
with a screwdriver. Make sure you loosen up all screws
before going to step 3.
1
2
Photo 1
1
030/17 70526
INSTRUCTIONS FOR
BATTERY REPLACEMENT
IMPORTANT: Before replacing the battery, turn off the
UPS and unplug the UPS cord from the wall outlet.
PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY
TO AVOID INJURY OR DAMAGE TO THE UNIT
Venus UPS - Models 600VA & 800VA

Turn the UPS down side up and shake all 4 screws
off.
3
Pull top cover up about 1.5 inches from the back.
Then pull front panel up slightly and separate from
chassis as shown below.
4
Photo 2
Turn top cover on the side as shown in photo 3.
5
Photo 3
2
INSTRUCTIONS FOR BATTERY REPLACEMENT

Unplug the red wire first by pulling it from the
red terminal, then the black one.
6
Photo 4
Unscrew the bracket covering the battery with
a screwdriver as shown on photo 5.
WARNING: Do not make any contact with the
battery terminals with the screwdriver or any
other metal materials like watches, rings, etc.
Electric shock could occur and it could cause
harm to you and the battery.
7
Photo 5
3
BATTERY
BRACKET
BATTERY
BRACKET
INSTRUCTIONS FOR BATTERY REPLACEMENT

Photo 6
Remove the battery by pulling up. It should slide out
easily.
8
Screw cover bracket back on as shown on Photo 7.
There is only one screw for each side. Make sure
the bracket sits on top of the holes as shown on
photo 7b.
10
Photo 7
4
Photo 7b
Place new battery in by making sure the terminals
are facing as shown on photo 6. The battery should
slide in and fit comfortably in its place.
9
SCREWS FOR
BRACKET
SCREWS FOR
BRACKET
HOLES FOR
SCREWS
HOLES FOR
SCREWS
INSTRUCTIONS FOR BATTERY REPLACEMENT

12
Photo 9
Put top cover back as shown on photo 9. Make sure
there are no wires coming out when putting top cover
back on.
Connect the black wire first to the black terminal
then, the red wire to the red terminal.
11
Photo 8
5
INSTRUCTIONS FOR BATTERY REPLACEMENT

Connect the top of the front panel into the holes
on the top cover and push towards chassis.
13
Photo 10b
Photo 10
14 Push down the top cover together with the chassis
and snap the front panel in place completely, as
shown below.
Photo 11
6
HOLESHOLES
INSTRUCTIONS FOR BATTERY REPLACEMENT

Drop screws inside hole making sure the head of
the screw is up. Screw all 4 screws back in until
tight.
Hold all panels together tightly and turn UPS
upside down.
16
15
Photo 12
Photo 13b
7
Photo 13
INSTRUCTIONS FOR BATTERY REPLACEMENT

Test the UPS by pressing the button and making sure
the "Protected" green LED comes on (LED model) or
the LCD diagnostic display comes on (LCD model).
Turn UPS off by pressing the button again.
17
Finally, plug all your equipment back to the UPS and
turn UPS on by pressing the button.
18
Photo 14 - LED Model Photo 14b - LCD Model
19 Recycle the used battery:
• Never dispose the batteries in a fire. It may
explode.
• Do not open or mutilate the batteries. Released
electrolyte is harmful to the skins and eyes. It
may be toxic. A battery can present a risk of
electrical shock and high short circuit current.
To recycle properly the used battery, please do not
discard the battery into the trash bin. Please follow
your local laws and regulations; you may contact
your local recycling waste center for further
information to dispose of it properly.
1760 Stebbins Drive - Houston, Texas 77043
Tel:[phone] - Fax:[phone]
E-mail: [email protected]
www.smartpowersystems.com