Smart Standard SDH-0066-BIGWHEEK-BK User manual

1.1,
2.1,
3.1,
3.2,
3.3,
4.1,
4.2,
4.3,
4.4,
Product Content
1 x Rail
5 x Anchor
5 x Lag Bolt
5 x Wall Spacer
(For concrete wall)
(For wood stud)
4 x Long Door Bolt2 x Hanger
2 x Rubber End
1 x Floor Guide
2 x Door Stopper
1 x Hex Key
2.2,
Measurements
A
D
16” 16” 16” 16”
B
1/”
HH+1/”
C
G
F
⁄”
E
1/”
3/”
8/”
78/”
Overall Rail length is 78/”.
A
C
G
D
B
F
E
The gap between each pre-drilled hole is 16”.
Door height is H.
The height of holes on the wall is H+1/”.
Distance from the bottom of the door to the floor is ⁄”.
End of the rail is 8/” away from the entrance of the door.
Distance from door top side to holes on the wall is 1/”.
Tools Needed
1,
2,
Pencil
Phillips Screwdriver
Drill
Wrench3,
4,
5,
Plumb Bob
Level
6,
Tape7,
9, Drill Bit
8, Drill Bit
Instructions
It is very important to determine whether you will be installing
a Header Board prior to installing the track.
Due to many overlapping factors such as the location of wall
studs (Our rail come with pre-drilled holes every 16” on center),
the weight of a barn door and the various types of trim used in
homes, we recommend using a Header Board in all situations.
Please install a 1” x 4” or 1” x 6” Header Board above the door
opening directly into studs.
Header Board must be solid wood and measure at least the full
length of the track or longer.
H+1/”
* Header Board and Lag Bolts
for installing Header Board
are not included in kit.
1
We provide 2 kinds of screws for you to install rail onto
concrete wall or drywall.
2
Place the rail against the wall, and use a pencil to mark
where the holes should be.
Make sure the height of holes on the wall is H+1/”.
Level can make the
rail horizontal.
A
B
Concrete wall Installation.
Install the anchor to holes on the concrete wall first,
then install carriage bolt to anchor.
Drywall Installation.
Install the lag bolt to wood stud or head board directly.
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard
3
A B C D
Do not screw it in
place at this stage
Insert door stoppers into rail. Install door stoppers
between A-B and C-D. Door stopper is used to prevent
the hangers coming out of the rail.

Install the floor guide. Put floor guide on the floor first
to fix a suitable position and make a mark so that the
tip of the floor guide can work well in the slot.
Use drill bit to drill holes on the floor where the mark is
and then install the floor guide.
8
9
Hang the door over the rail 10
Adjust the 2 door stoppers to find a suitable position,
Use the hex key to screw the door stoppers in place.
TM
S
Smart
tandard
Sliding Door Hardware
Manual (1 Door BigWheel 6.6ft)
1”
The rubber ends are used to protect the door from
touching the rail when sliding the door. You need
to drill holes on the door top side, please drill the
holes /” away from the edge of the door. Then
install the rubber ends on the door.
Turn the rubber ends approximately 180 degrees so
that they are stuck between the door and the rail.
/”
Email: [email protected]
1/”
3/”
Install the hangers onto the door according to
the measurements in the pictures below.
Maximum door thickness is 1/”. If your door’s
thickness is less than 1/”, please add some bolt
washers or cut the long door bolts to a suitable
length to fit the door.
7
/”
/”
6
5
Use router or circular saw to create a kerf at bottom
of the door, along the center to allow the tip of the
T-shaped floor guide to fit in between, to keep your
door stable and prevent the door bottom swinging
back and forth when you slide it open and closed.
4
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
TM
S
Smart
tandard
S
Smart
tandard
TM
S
Smart
tandard