Assa Abloy SARGENT 268 Series User manual

WITH POWER OFF, CONNECT WIRES AND INSTALL CLOSER INTO PREPARED FRAME WITH
SPRING ADJUSTMENT SCREW AWAY FROM HINGE. (268 CSPS DOOR CLOSER SHOWN)
INSERT ARM ROLLER INTO TRACK THRU
CUTOUT AND TEMPORARILY LET ARM
LAY ON A TRACK.
VERIFY THE HAND OF THE CLOSER BEFORE INSTALLING. REFERRING TO THE STAMPING ON THE CLOSER END CAP AS SHOWN
A
ASSEMBLY OF ARM TO DOOR
CLOSER SPINDLE
1. USING 1/8" ALLEN WRENCH, TURN LATCHING
SPEED AND DOOR CLOSING SPEED VALVES
(SEE FIGURE 1) CLOCKWISE UNTIL THEY STOP.
DO NOT FORCE VALVES.
2. USING ADJUSTABLE WRENCH, ROTATE
DOOR CLOSER SPINDLE (SEE FIGURE 1)
90° CLOCKWISE FOR LEFT HAND DOOR AND
COUNTER CLOCKWISE FOR RIGHT HAND DOOR.
3. OPEN DOOR APPROXIMATELY 50° WITH THE
DOOR CLOSER SPINDLE NOW STATIONARY,
MOVE THE END OF THE ARM TO THE SPINDLE
END UNTIL SQUARE HOLE IN THE ARM LINES
UP WITH THE SPINDLE END SQUARE (AS SHOWN).
PUSH ARM UP INTO POSITION ON THE SPINDLE
AND SECURE WITH SECURITY SCREW
AND WASHER.
4. RETURN LATCHING AND DOOR SPEED
VALVES TO NORMAL POSITION
LEFT
HAND DOOR
RIGHT
HAND DOOR
PULL
HINGE SIDE
PULL
HINGE SIDE
STOP (PUSH) SIDE STOP (PUSH) SIDE
268/269 CSPS/CSPD DOOR CLOSERS ARE HANDED AND SHOULD BE SAME HAND AS DOOR
RED– NORMALLY CLOSED
BLUE– NORMALLY OPEN
BLACK– COMMON
FROM DOOR
POSITION SWITCH TO MONITORING SYSTEM
MAINARM
INDEX MARK
ON SPINDLE
R.H. SHOWN VIEW
LOOKING UP
OPTIONAL: 268 CSPD
DOOR CLOSER HAS TWO
SETS OF WIRES
4 EACH
12-24 X 5/8" MS
(PROVIDED)
B
DE
DATE CODE:
MONTH AND YEAR
MODEL NUMBER
AND HANDING
When using the optional
circuit tester, refer to page 3
for instructions
CINSTALL TRACK IN DOOR AS SHOWN USING
TAMPER PROOF SECURITY SCREWS
PROVIDED.
HINGE EDGE
OF DOOR
CUTOUT AWAY
FROM HINGES
1
268, 269 (CSPS OR CSPD)
SECURITY OVERHEAD CONCEALED DOOR CLOSER
ITH INTEGRATED SINGLE OR DOUBLE S ITCH
CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.
FOR INSTALLATION ASSISTANCE CALL SARGENT AT 1-800-727-5477 • www. argentlock.com
Copyright © 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All right re erved. Reproduction in whole or in part without the expre written
permi ion of Sargent Manufacturing Company i prohibited.
A7326C 06-15-09

REGULATING DOOR SPEED AND LATCHING SPEED
USE 1/8" ALLEN WRENCH AND TURN VALVES CLOCKWISE TO SLOW DOWN OR COUNTER CLOCKWISE TO SPEED UP DOOR MOVEMENT. SEE FIGURE 2.
REGULATING BACKCHECK
THE INTENSITY OF BACKCHECK ACTION IS REGULATED BY A BACKCHECK VALVE.
TURN CLOCKWISE TO INCREASE OR COUNTER CLOCKWISE TO DECREASE CHECKING.
INSTALL TOP PLATES USING SECURITY
SCREWS WHEN ALL ADJUSTMENTS
ARE MADE. 8 SCREWS REQUIRED
2
SWITCH ACTUATION POINT ADJUSTMENT
(SEE FIGURE 1)
1. REMOVE TOP PLATES FROM THE CLOSER (IF REQUIRED).
2. TO ACCESS THE ADJUSTMENT SCREW, OPEN THE DOOR
ABOUT 10°.
3. TO ADJUST SWITCH TO RESPOND WHEN DOOR IS NEARER
THE CLOSED POSITION, LOOSEN ADJUSTMENT SCREW
SLIGHTLY AND USING THE HEX KEY AS DRIVE ROTATE
CAM FOR SMALL ANGLE:
—CLOCKWISE FOR RIGHT HAND DOOR
—COUNTER CLOCKWISE FOR LEFT HAND DOOR
TIGHTEN THE ADJUSTMENT SCREW. CLOSE THE DOOR.
IF THE SWITCH DOES NOT RESPOND IN THE DESIRED DOOR
POSITION, REPEAT ADJUSTMENT.
CLOSING SPEED
RANGE
LATCHING
SPEED RANGE
BACKCHECK
RANGE
FIGURE 1
F
G
FINAL ADJUSTMENT AND REGULATING PROCEDURE
H
3/16 HEX
CAUTION: SET VALVE FOR A SLIGHT CUSHIONING EFFECT; IT IS DAMAGING TO CLOSER IF
THE CHECKING ACTION IS TOO ABRUPT. BACKCHECK SHOULD NEVER BE USED IN LIEU OF
A DOOR STOP.
I
J
R
SPRING POWER ADJUSTMENT
FOR EXTERIOR DOORS AND WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER
AS NEEDED BY TURNING SPRING ADJUSTING SCREW CLOCKWISE.
IF NECESSARY, DECREASE SPRING POWER TO LOWER OPENING FORCE BY ROTATING
SPRING ADJUSTING SCREW COUNTERCLOCKWISE. ONLY OPEN DOOR A FEW INCHES
WHILE ADJUSTING.
1/16 HEX KEY CAM ADJUSTMENT SCREW
FIGURE 2
3/16" SPRING POWER
ADJUSTING SCREW
BACKCHECK
VALVE
CLOSING
SPEED VALVE
LATCHING
SPEED VALVE
Copyright © 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All right re erved. Reproduction in whole or in part without the expre written
permi ion of Sargent Manufacturing Company i prohibited.
A7326C 06-15-09

PROBLEM: NO SIGNAL FROM DOOR POSITION SWITCH TO THE MONITORING/ALARM SYSTEM
AFTER ALL POSSIBLE ADJUSTMENTS WERE MADE.
CHECK: SWITCH ASSEMBLY
HOW TO CHECK SWITCH ASSEMBLY:
•DISCONNECT POWER FROM THE UNIT
• REMOVE UNIT FROM FRAME
• DISCONNECT SWITCH ASSEMBLY FROM MONITORING SYSTEM
• CHECK SWITCH ASSEMBLY FOR OPEN CIRCUIT
CIRCUIT CHECK:
1. MAKE SURE SWITCH IS ACTUATED.
2. SET METER TO OHMS (Ω).
3. PUT ONE LEAD OF METER TO POST OF BLACK WIRE (C) AND OTHER LEAD TO POST OF RED WIRE (NC) ON THE
CONNECTOR. METER SHOULD SHOW OPEN CIRCUIT.
4. LOOSEN THE ADJUSTMENT SCREW AND ROTATE THE CAM TO DEACTIVATE THE SWITCH. METER SHOULD SHOW CLOSE CIRCUIT.
5. PUT ONE LEAD OF METER TO POST OF BLACK WIRE (C) AND OTHER LEAD TO POST OF BLUE WIRE (NO) ON THE CONNECTOR.
METER SHOULD SHOW OPEN CIRCUIT.
6. ROTATE THE CAM TO ACTIVATE THE SWITCH. METER SHOULD SHOW CLOSE CIRCUIT.
IF SWITCH ASSEMBLY WORKS AS DESCRIBED: – REINSTALL CLOSER
– ADJUST SWITCH ACTUATION POINT AS DESCRIBED IN STEP F
– INSTALL TOP PLATES
IF SWITCH ASSEMBLY IS WORKING PROPERLY PROBLEM MAY BE ELSEWHERE IN THE SYSTEM. CHECK THE MONITORING/ALARM SYSTEM.
SWITCH
BLACK
(C)
BLUE
(N.O.)
RED
(N.C.)
3
TROUBLESHOOTING 268 CSPS/CSPD
HOW TO USE CIRCUIT TESTER
1. REMOVE COVER PLATES AND PULL PLUG CONNECTION DOWN THROUGH SLOT AND DISCONNECT
2. CONNECT CIRCUIT TESTER AND PUSH PLUG CONNECTION BACK INTO SLOT SO DOOR COULD CLOSE
3. REFER TO (STEP F) FOR ADJUSTMENT INSTRUCTIONS
GREEN LIGHT ON CIRCUIT TESTER INDICATES THAT DOOR IS CLOSED, RED LIGHT INDICATES DOOR IS OPEN.
4. ONCE SWITCH IS ADJUSTED DISCONNECT CIRCUIT
TESTER AND RE-ASSEMBLE
ORDERED SEPARATELY,
USE PART NUMBER 63-4335 WHEN ORDERING
GREEN
RED
ACCESSORIES
Copyright © 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All right re erved. Reproduction in whole or in part without the expre written
permi ion of Sargent Manufacturing Company i prohibited.
A7326C 06-15-09