Dormakaba ED100 User manual

ED100/ED250
Automatic swing door operators
Service Manual
DL4614-050 – 02-2018
| EN |

2
ED100/ED250 02-2018DL4614-050
dormakaba ED100/ED250 Service Manual Table of Contents
Table of contents 
 General information 
 Product Description 
 Safety information 
 ED/ED 
. Operator component view 
. Header assembly 
 Recommended tools, tightening torque 
 User interface 
. Overview 
.  button keypad and display 
. Program switch panel 
 Terminal board accessory interfaces 
. ED/ED terminal board accessory
interfaces 
 ED/ED door signage 
. Full energy operators 
. Low energy operator, ED 
. Door signage, full energy single swing door 
. Door signage, low energy single swing door 
. Door signage, full energy double swing
doors 
. Door signage, low energy double swing
doors 
 Maintenance 
. Safety label, automatic swing doors 
. Safety label, low energy swinging doors 
. ED/ED environment and cleaning 
. Yellow LED, service level 
. Pull arm maintenance 
.. Pull arm torque requirements 
. Push arm maintenance 
. Push arm torque requirements 
Table of contents
10 Measure reveal depth, parameter rd 19
. Reveal depth parameter rd 
. Record reveal depth measurement,
rd value 
. rd parameter values 
11 Operator spring tension 20
. Set operator spring tension 
12 Power fail closing speed 21
. Set power fail closing speed 
13 Perform learning cycle 22
. Perform learning cycle 
14 ANSI/BHMA standards 23
. A. Power operated pedestrian
doors 
. A. Low energy power operated
doors 
15 Parameters 26
. Parameters 
. Driving parameters detail 
16 Troubleshooting 38
. Information and error codes 
. Red LED status codes 
. Troubleshooting chart, "ln" codes 
. Troubleshooting chart, "E" codes 
17 Upgrade cards 43
. Upgrade cards 
. Container module 
. Installing upgrade cards 
18 dormakaba handheld 45
. dormakaba handheld terminal 
. dormakaba handheld; configuration
parameters 
. dormakaba handheld; driving parameters 
. dormakaba handheld; special functions
(Upgrade cards) 
. dormakaba handheld; diagnostics 
. dormakaba handheld; firmware update 

3
ED100/ED250 02-2018DL4614-050
dormakaba ED100/ED250 Service Manual Chapters 1 and 2
. Service Manual
This manual provides service information for
ED100/ED250 automatic swing door operators.
. Manual storage
This document must be kept in a secure place, and
accessible for reference as required.
If the door system should be transferred to another
facility, insure that this document is transferred as well.
. dormakaba.com website
Manuals are available for review, download, and printing
on dormakaba.com/us website.
. Dimensions
Unless otherwise specified, all dimensions are given in
inches (“).
CAUTION
This symbol warns of a potentially unsafe
procedure or situation.
Fig.2.1 ED100/ED250 header
. Symbols used in these instructions.
WARNING
This symbol warns of hazards which could result
in personal injury or threat to health.
NOTICE
Draws attention to important information
presented in this document.
TIPS AND RECOMMENDATIONS
Clarifies instructions or other information
presented in this document.
. Symbols used in these instructions.
WARNING
Electric shock hazard!
WARNING
Hand pinch point and crushing hazards!
WARNING
Crushing hazards!
. Intended use
• ED/ED automatic swing door operators are
designed to be installed on an interior building
surface.
• These operators are used for opening and closing
interior or exterior swing doors.
• Maximum door weight depends on the operator and
door width.
ED
• Maximum door width of  inches at  pounds.
ED
• Maximum door width of  inches at  pounds.
• Maximum door width of  inches at  pounds.
Fig.2.2 ED100/ED250 operator
 General information
 Product Description

4ED100/ED250 02-2018DL4614-050
dormakaba ED100/ED250 Service Manual Chapter 3
. Safety instructions
This document contains important information for
servicing ED100/ED250 swing door operators.
Review applicable information thoroughly prior to
operator troubleshooting and maintenance.
. Door signage requirements
Proper signs and labels shall be applied and maintained on
the door controlled by the ED100/ED250 swing door
operator per one of the following ANSI/BHMA standards:
• ANSI/BHMA A.-, Standard for power
operated doors, paragraph , signage.
• ANSI/BHMA A.-, Standard for power
assist and low energy power operated doors,
paragraph , signage.
. Safety warnings
WARNING
Hazard to mechanical processes by use of
control settings, elements, or procedures not
documented in this manual!
WARNING
Electric shock hazard!
• By use of control elements, settings, or
procedures not documented in this manual!
WARNING
Work on electrical equipment and 115 Vac wiring
must be performed only by qualified personnel!
 Safety information
WARNING
Hand pinch point and crushing hazards at door
closing edges!
WARNING
Crushing hazards at door closing edges!
WARNING
Hand pinch point and crushing hazards!
• Pull arm and track
• Push arm
Fig. 3.1 Door closing edges
1 2
3
1Secondary closing edge
2Opposing closing
edge
3Main closing edge
Fig. 3.2 Pull arm and track
Fig. 3.3 Push arm

5
ED100/ED250 02-2018DL4614-050
dormakaba ED100/ED250 Service Manual Chapter 4
Fig. 4.1.7 ED100/ED250 components view 1 Fig. 4.1.8 ED100/ED250 components view 2
 ED/ED
1
19
2
4
5
6
17
8
9
14
15
16
18
20
3
21
23
27
2
3
18
20
4
5
24
21
22
6
12
11
9
8
16
15
14
23
25
26
27
17
1Power switch
2120 Vac terminals
3Housing unit
4Drive axle connection
5Operator (motor,
gear, spring
6Spring tension
adjustment, closing
force
84 button user
interface
9Information display
10 Slot for internal
program switches
11 Potentiometer,
power fail closing
speed
12 Terminal jumper
socket, push or pull
mounting
14 Slot for upgrade cards
15 RJ45 socket for
communication cable
between two operators,
double door system
16 Com 1 service
connector
17 Accessories terminal
board
18 Mounting plate
19 Customer ground
terminal
20 Guide pin
21 Ribbon cable
22 Ribbon cable socket
23 Upgrade card socket
24 Motor
25 Encoder socket and
cable
26 Motor socket and
cable
. Operator component view

6ED100/ED250 02-2018DL4614-050
dormakaba ED100/ED250 Service Manual Chapters 4 and 5
 Recommended tools, tightening torque
1
5
Fig. 7.1.1 Recommended tools
5.1 Recommended tools
1T-handle hex key,
5 mm
2Hex keys, 2.5 mm,
3 mm, 6 mm
3Screwdriver, flat blade
4Door pressure gauge,
0 to 35 ft - lbf
5Screwdriver, Phillips,
#2, #3
6Torque wrench,
3 to 35 ft lb
6.1 5 mm hex key socket
7Open end wrench,
13 mm
8Screwdriver, flat
blade.,
M2 (1/16 to 3/32")
2
4
7
Fastener size ft lb N m
M . 
M  .
M  
M  
M  
5.2 Standard tightening torque
.. Standard tightening torque
3
8
1Header
2Program switch panel
3Pull arm with track
4Access hole for spring
tension
•
Fig. 4.2.1 ED100/ED250 header assembly
. Header assembly
1
2
3
4
6
6.1

7
ED100/ED250 02-2018DL4614-050
dormakaba ED100/ED250 Service Manual Chapter 6
 User interface
. Overview
Fig. 6.1.1 Operator display and keypad
12 digit display
24 button keypad
•
.. Operator user interfaces
.  button keypad and  digit display.
•  button keypad; to input and adjust
door parameter values.
•  digit display; parameter values, error
and information codes.
.. button keypad functions
Fig. 6.2.1 4 button keypad and display
12 digit display
24 button keypad
.  button keypad and display
Right button
. Access parameter menu,
press button >  seconds.
. Edit selected parameter.
. Save changed value.
Left button
. Cancel parameter edit
process.
. Exit parameter menu,
press button <  s.
Both buttons
together
. Acknowledge errors,
press both buttons <  s.
. Reset, press both
buttons >  s.
Up button
. Scroll through parameters
and error messages.
. Increase parameter value.
Down button
. Scroll through parameters
and error messages.
. Reduce parameter value.
. Opening pulse, press
button <  s.
. Learning cycle, press
button >  s.
. Reset with factory setting,
press button >  s
(program switch Close
position).
. Identify operator
orientation for display.
12
1
2

8ED100/ED250 02-2018DL4614-050
dormakaba ED100/ED250 Service Manual Chapter 6
. Program switch panel
Fig. 6.3.1 Program switch panel
.. Program switch door control modes
. Auto
Door opens automatically when one of
the activators (Chapter ) is actuated or
triggered, and closes on expiration of
adjustable hold open time.
. Close
Door closes automatically, or remains
closed until program switch position
changed.
. Open
Door opens automatically and remains
open until program switch position
changed.
.. Exit only switch modes
. Off
Internal and external activation sensors
both active.
. On
External activation sensor disabled when
door fully closed. Only internal activation
sensor will enable door opening.
6.4 Operator status LEDs
Fig. 6.4.1 Operator status LEDs
.. Operator status LEDs
Header cover must be opened to view LEDs.
. Red LED
Blinking codes are used to indicate "ln__"
information (system status or operating
conditions) or certain error codes "E__".
. Yellow LED
Maintenance interval indicator. When
illuminated, an indication the operator
system has to be serviced.
. Green LED
• On, internal  Vdc power is On.
• Off, internal  Vdc power is Off.
TIPS AND RECOMMENDATIONS
Details on LED status codes and
maintenance intervals can be found
in Chapter 16, Troubleshooting.
1Red LED
2Yellow LED
3Green LED
4Power switch
1
1.1
1.2
1.2
1Program switch
panel
2Program switch,
3 position
3Exit Only switch,
2 position
4Comm port for
dormakaba
handheld
1
2
3
4

9
ED100/ED250 02-2018DL4614-050
dormakaba ED100/ED250 Service Manual Chapter 7
 Terminal board accessory interfaces
. ED/ED terminal board accessory interfaces
Fig. 7.1.1 Terminal board electrical connections
1Green LED (Para. 6.4)
2Yellow LED (Para. 6.4)
3Red LED (Para. 6.4)
4Key (red insert)
location in socket.
Assigned plug has tab
broken off in same
location.
5Jumpers, factory
installed at following
terminals:
•  and a
•  and *
•  and *
* Remove jumpers if
safety sensors
installed.
6DCW®upgrade card
plug included in scope
of delivery.
7Fire protection upgrade
card plug included in
scope of delivery.
(v.)
Night-bank,
K resistor
not required
97 98 99 30 31 32 34 33 3335 136144a
3BA157 57a 14231413115 17 311113 3
43 36463621G 3
+ 24 V
Signal input 0 V
Part
ial Open
Permane
nt Open
E
xit Only
Automatic
Off
N.C.
COM
Test output
X5X4
X3
X6 X9 X1 X7
+ 24 V
X8
0 V
X10
8 - 24 AC/DC + 5% Wet
DCW bus Swing side Approach side
Safety sensors
Activation inputs
Interior Exterior
Night-
bank
input
+ 24 V
Signal input 0 V + 24 V
+ 24 V Signal input
Signal input 0 V
0 V
Test output
0 V
24 V
Maximum current
load: 1.5 A
Output
COM
N.O.
N.C.
0 V
Locking relay
Maximum current:
1A, 48 V DC/AC
Locking feedback contact
0 V
0 V
+ 24 V
0 V
0 V
Signal input
N.O.
Smoke
detectors
Emergency
close
Night
trigger
Program, exit only
switches
Door status
24 VDC
Class II
1
2
3
4
5
6
7
55
Reference Note 1
Note 1: Terminals 3 and 43 also used for
swing side overhead presence sensor
input when Parameter ST is set to 7 or 8.
Reference Chapter 15, Parameters.

10 ED100/ED250 02-2018DL4614-050
dormakaba ED100/ED250 Service Manual Chapter 8
Signage and warnings are specified in ANSI /BHMA
A., American National Standard for power
operated pedestrian doors, paragraph .
.. Door, one way traffic
DD0739-020
.. Overview
 ED/ED door signage
Fig. 8.1.1 One decal approach, non-approach
. Arrow and AUTOMATIC DOOR, one side of decal.
• Shall be visible from approach side of a swinging door,
mounted on door at a height of " ± " from floor to
centerline of sign.
. DO NOT ENTER and AUTOMATIC DOOR, one side of
decal (or separate decal for solid doors).
• Shall be visible from non-approach side of door that
swings towards pedestrians attempting to travel in
wrong direction.
. Full energy operators
Fig. 8.1.2 Separate decals approach, non-approach
.. Door, two way traffic
. Arrow and AUTOMATIC DOOR decal.
• Shall be visible from approach side of a swinging door,
mounted on door at a height of " ± " from floor to
centerline of sign.
. "CAUTION AUTOMATIC DOOR" decal.
• Swinging doors serving both egress and ingress shall
have a "CAUTION AUTOMATIC DOOR" sign visible
from swing (non-approach) side of door.
• Sign shall be mounted on door at a height of  ± "
from floor to center line of sign.
Fig. 8.1.3 ACTIVATE SWITCH TO OPERATE decal,
knowing act device
.. Knowing act door
. ACTIVATE SWITCH TO OPERATE decal.
• Knowing act doors shall have signage which says
"ACTIVATE SWITCH TO OPERATE" on side of door
having knowing act switch or other knowing act device.
. AUTOMATIC CAUTION DOOR decal.
• All low energy doors shall be marked with signage
visible from both side of door with the words
"AUTOMATIC CAUTION DOOR".
• Signs shall be mounted " ±" from floor to
centerline of sign.
Fig. 8.2.1 AUTOMATIC CAUTION DOOR decal
Fig. 8.2.2 ACTIVATE SWITCH TO OPERATE decal,
knowing act device
.. Push/Pull used to initiate door operation
Fig. 8.2.3 PUSH TO OPERATE, PULL TO OPERATE decals
. PUSH TO OPERATE, PULL TO OPERATE decals.
• When push/pull is used to initiate operation of door
operator, doors shall be provided with the message
"PUSH TO OPERATE" on push side of door and
"PULL TO OPERATE" on pull side of door.
. Low energy operator, ED
.. Overview
Signage and warnings are specified in ANSI /BHMA
A., American National Standard for power assist
and low energy power operated doors.
.. All low energy doors
.. Knowing act switch used to initiate door
operation
. ACTIVATE SWITCH TO OPERATE decal.
• When a knowing act device is used to initiate operation
of door operator, door shall be provided with sign on
each side of door where switch is operated with
message "ACTIVATE SWITCH TO OPERATE".