Dictator DICTAMAT OpenDo User manual

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430 Page 07.045.1
Technical Manual
DICTAMAT OpenDo
Technical Manual
DICTAMAT OpenDo
Page 04.045.01
You can find the current version of our manual on our website under «Downloads»:
https://en.dictator.de/products/door-drives-gate-drives/operators-sliding-doors/dictamat-opendo/

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430Page 07.045.2
Technical Manual
DICTAMAT OpenDo
Table of Contents
Page
1. General notes 04.045.03
a) Target group
b) Warning notice
c) Requirements
d) General Safety Instructions
e) Cables to be used
2. Components 04.045.04
a) Scope of delivery 710650
b) Scope of delivery 710651
c) Scope of delivery 710652
d) Scope of delivery 710653 04.045.05
e) Scope of delivery 710654
3. Mounting 04.045.06
a) Mounting the door drive
b) Preparing the door 04.045.07
c) Inserting the components into the rail 04.045.08
d) Fastening the rail
e) Adjusting the door 04.045.09
f) Placing and tightening the toothed belt 04.045.10
g) Installing the controller 04.045.11
h) Floor guide and final stopping devices 04.045.12
4. Technical data 04.045.13
5. Electrical connection 04.045.13
6. Setting the desired functions 04.045.14
a) Control functions
b) Overview 04.045.15
c) Adjusting the potentiometer
d) Setting the DIP switches 04.045.16
e) Accepting the settings 04.045.17
7. Commissioning 04.045.18
8. Error indication 04.045.19
9. Maintenance 04.045.20
10.Inspection book 04.045.21
a) Information on the construction project
b) Work description 04.045.22
Page 07.045.02

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430 Page 07.045.3
Technical Manual
DICTAMAT OpenDo
Page 07.045.03
1. General Notes
This manual is intended for qualified personnel only. Installation may
only be carried out by technically trained and qualified persons. The
electrical connection may also only be carried out by a specialist.
This document contains important information on installation, electrical
connection and commissioning of the product.
The document must be read before any work is carried out on the
electrical and electronic systems and must be kept accessible at all
times as part of the product.
In addition to this document, other documents, directives, standards
and laws for products of this type must be observed.
ATTENTION!
Danger to life from electric shock!
Dangerous injuries, death and damage to property can be caused by
dangerous electrical voltages!
The operation of all components is only permitted in undamaged condition.
Always disconnect from the power supply before carrying out any work and
secure against being switched on again.
The accident prevention regulations must be observed.
Cable Type of cable
Between motor and controller up to 20 m:
20 to 50 m:
50 to 100 m
Rotary encoder:
up to 50 m:
2 x 0.50 mm²
2 x 0.75 mm²
2 x 1.50 mm²
4 x 0.25 mm²
Between push button and
controller
optionally
up to 50 m: 4 x 0.25 mm²
Between power pack and
controller
up to 20 m:
20 to 50 m:
50 to 100 m:
2 x 0.50 mm²
2 x 0.75 mm²
2 x 1.50 mm²
1a) Target Group
1b) Warning Notice
1c) Requirements
1d) General Safety
Instructions
1e) Cables to be Used

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430Page 07.045.4
Technical Manual
DICTAMAT OpenDo
Page 07.045.04
2. Components
For single-leaf wooden doors up to 1100 mm width
• Door drive with clamping block and counter plate for rail
• Power pack 230 VAC / 24 VDC
• Controller with push-button OPEN/CLOSE
• Cover frame for flush-mounted box provided by customer
• Idler pulley
• Door actuator
• 4100 mm of toothed belt
• Aluminium rail, length 2000 mm
• 4 aluminium brackets for wall mounting of the rail including spacer
plates
• 2 wheel hangers with slide bearings
• 1 floor guide
• 2 final stopping devices for installation in the rail
For single-leaf wooden doors up to 1100 mm width; AISI 316 wheel
hangers
• Door drive with clamping block and counter plate for rail
• Power pack 230 VAC / 24 VDC
• Controller with push-button OPEN/CLOSE
• Push-button OPEN/CLOSE
• 2 cover frames for flush-mounted boxes provided by customer
• Idler pulley
• Door actuator
• 4100 mm of toothed belt
• Aluminium rail, length 2000 mm
• 4 aluminium brackets for wall mounting of the rail including spacer
plates
• 2 AISI 316 wheel hangers with ball bearings
• 1 floor guide
• 2 final stopping devices for installation in the rail
For single-leaf glass doors up to 1100 mm width
• Door drive with clamping block and counter plate for rail
• Power pack 230 VAC / 24 VDC
• Controller with push-button OPEN/CLOSE
• Cover frame for flush-mounted box provided by customer
• Idler pulley
• Door actuator
• 4100 mm of toothed belt
• Aluminium rail, length 2000 mm
• 4 aluminium brackets for wall mounting of the rail including spacer
plates
• 2 wheel hangers with slide bearings
• 1 floor guide
• 2 final stopping devices for installation in the rail
2a) Scope of delivery
710650
2b) Scope of delivery
710651
2c) Scope of delivery
710652

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430 Page 07.045.5
Technical Manual
DICTAMAT OpenDo
Page 07.045.05
For double-leaf wooden doors up to 1058 mm width per door leaf
• Door drive with clamping block and counter plate for rail
• Power pack 230 VAC / 24 VDC
• Controller with push-button OPEN/CLOSE
• Push-button OPEN/CLOSE
• 2 cover frames for flush-mounted boxes provided by customer
• Idler pulley
• Door actuator
• 8100 mm of toothed belt
• 2 aluminium rails, length 2000 mm
• 8 aluminium brackets for wall mounting of the rail including spacer
plates
• 4 wheel hangers with slide bearings
• 2 floor guides
• 3 final stopping devices for installation in the rail
2. Components - cont.
2e) Scope of delivery
710654
2d) Scope of delivery
710653
For single-leaf wooden doors up to 1600 mm width
• Door drive with clamping block and counter plate for rail
• Power pack 230 VAC / 24 VDC
• Controller with push-button OPEN/CLOSE
• Cover frame for flush-mounted box provided by customer
• Idler pulley
• Door actuator
• 4100 mm of toothed belt
• Aluminium rail, length 3000 mm
• 4 aluminium brackets for wall mounting of the rail including spacer
plates
• 2 wheel hangers with slide bearings
• 1 floor guide
• 2 final stopping devices for installation in the rail

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430Page 07.045.6
Technical Manual
DICTAMAT OpenDo
Page 07.045.06
3. Mounting
Fig. 1
3a) Mounting the Door
Drive
The drive is mounted directly on the supplied rail. To do this, insert
the clamping block into the rail, place the lateral mounting plate and
counter plate underneath the rail and screw all components together
with the supplied M6 x 25 mm screws.

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430 Page 07.045.7
Technical Manual
DICTAMAT OpenDo
125 mm
=
=
125 mm
Page 07.045.07
Fig. 2
3. Mounting - cont.
3b) Preparing the Door Now screw the door actuator and both wheel hangers firmly to the
door. The door actuator should always be fixed in the middle of the
door leaf. Make sure that the wheel hangers are fixed at a sufficient
distance from the outer edge of the door. This distance should be kept
so that the drive and the idler pulley still have sufficient space in the rail
next to the wheel hangers.
Recommended:
• 125 mm distance to the outer edge on both sides of the door
If not already present, an additional slot must be prepared in the door
leaf for the floor guide (Fig. 12, Pg. 12).

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430Page 07.045.8
Technical Manual
DICTAMAT OpenDo
max. 600 mm
Page 07.045.08
Fig. 3
Fig. 5
3. Mounting - cont.
3c) Inserting the
Components into
the Rail
Insert all components into the rail in the following order: Final stopping
device, wheel hanger, wheel hanger and idler pulley.
3d) Fastening the Rail To fix the rail, the supplied aluminium brackets are inserted into the
upper guide of the rail. In addition, the spacer plates can be used if the
bracket cannot be fixed directly to the wall (Fig. 4).
In order to ensure a stable hold of the rail, please ensure a distance
of max. 600 mm between the individual brackets during installation
(Fig.5).
Fixing brackets
Rail
Spacer plate
Fig. 4

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430 Page 07.045.9
Technical Manual
DICTAMAT OpenDo
Page 07.045.09
Fig. 6
Fig. 7
3. Mounting - cont.
3e) Adjusting the Door Now the door can be hung up and adjusted to the required height with
the screws of the hangers.
Then secure the door with the lock nuts.
Adjust the required height
Lock nut

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430Page 07.045.10
Technical Manual
DICTAMAT OpenDo
3. Mounting - cont.
Fig. 8
Fig. 9
3f) Placing and
Tightening
the Toothed Belt
To tighten the toothed belt, first remove the cover cap on the drive (Fig.
8) and loosen the clamping plate on the door actuator. Now guide the
toothed belt around the toothed pulley on the drive and the idler pulley
(Fig. 9), shorten to the required length and secure it again on the door
actuator through the clamping plate (Fig. 10, Pg. 11).
To tension the toothed belt, move the idler pulley in the rail until the belt
is well tensioned. This must not hang slack in the system. Then secure
the position by tightening the idler pulley.

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430 Page 07.045.11
Technical Manual
DICTAMAT OpenDo
Fig. 11
3. Mounting - cont.
Fig. 10
3g) Installing the
Controller
The supplied OPEN/CLOSE button, the control unit, the cover frame
and the power pack are installed in a single flush-mounted box (see
Fig. 11). This must first be installed by the customer (flush-mounted
box according to DIN 49073, rocker dimension 55 mm; installation
opening 60 mm).
Information on the electrical connection can be found on page
04.045.13.
3f) Placing and
Tightening
the Toothed Belt -
cont.

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430Page 07.045.12
Technical Manual
DICTAMAT OpenDo
7 mm
14 mm5 mm
Fig. 12
Fig. 13
3. Mounting - cont.
3h) Floor Guide and
Final Stopping
Devices
When mounting the floor guide, make sure that it does not jam. It may
be necessary to adjust the width or height of the slot for the floor guide.
If necessary, check again that the door hangs vertically (Fig. 13).
The final stopping devices can easily be secured in the desired position
using grub screws.

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430 Page 07.045.13
Technical Manual
DICTAMAT OpenDo
4. Technical Data
Fig. 14
Door width standard version for single-leaf doors: 675 mm to
1600mm
standard version for double-leaf doors, per leaf: 675
mm to 1058 mm; both door leaves must have the same
dimensions!
Door weight single-leaf doors: max. 80 kg
double-leaf doors: max. 40 kg/leaf
Door thickness timber: 19 - 48 mm, glass 10 or 12 mm
Speed max. 0.25 m/s; adjustable, depends on door weight:
80 kg => max. 0.2 m/s; 60 kg => max. 0.23 m/s;
40 kg => max. 0.25 m/s
Hold-open time adjustable between 5 and 30 s
Rated input voltage 100 to 240 VAC, 50 to 60 Hz
Motor rating 50 W
Safety microprocessor controlled switch-off in case of obstacles
IP rating IP 55
Operating temperature -20° to +50 °C
Operational life min. 400 000 cycles
Max. number of operations up to 50 operations per hour
5. Electrical
Connection CAREFUL!
Damage to the component due to incorrect connection!
When connecting, it is imperative that the correct polarity is observed!
24 VDC (+) power pack
Earth (–) power pack
Inputs
for on-site
operation
Earth
Stop
Open
Close
brown
green
yellow
white
+ red
– blue
+5 VDC
Signal 2
Signal 1
Earth
Rotary encoder

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430Page 07.045.14
Technical Manual
DICTAMAT OpenDo
The DICTAMAT OpenDo enables many different functions.
It should be noted that the functions in deadman mode and in impulse
mode may differ (see table below).
For opening and closing the door by radio or motion detector, it is ab-
solutely necessary to set the impulse mode.
Basic
operating
mode
Deadman
operation Impulse operation
OPEN only per button
- per button (Standard)
- Push-and-go (pushing the door
shortly by hand activates the
door operator which will auto-
matically open the door)
- Radar or radio
CLOSE only per button
- per button (Standard)
- Automatic closing (door closes
automatically after an adjustable
time)
- Radar oder radio
Safety
(detection of
obstacles) in
OPEN and
CLOSE
Stop
- Reversing (the door stops and
then moves in the opposite
direction)
- Stop: only possible when no
automatic closing has been set.
Door perma-
nently open
Door remains
open until the next
CLOSE command
Also possible with automatic
closing time set by key combi-
nation (press OPEN and CLOSE
simultaneously).
Moving the
door in case
of a power
cut
Can be moved by hand with little effort.
6. Setting the Desired Functions
6a) Control Functions

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430 Page 07.045.15
Technical Manual
DICTAMAT OpenDo
ON
1 2 3 4 5 6 7 8
6. Setting the Desired Functions - cont.
Fig. 15
6b) Overview The settings of the OpenDo are made by means of the potentiometer
P1, the DIP switches and the RESET button on the control unit.
The following diagram shows where these components are located on
the controller.
DIP switchesReset button
LEDs for function
indication
Potentiometer P1
Potentiometer P1
The potentiometer can be used to set the hold-open time of the door
operator.
The following applies:
Turning clockwise →Hold-open time is extended
Turning counterclockwise →Hold-open time is reduced
IMPORTANT: The potentiometer has a stop in both directions of rotation
which must not be overtightened! The potentiometer must therefore
always be turned with extreme caution and suitable tools! Damage can
lead to malfunctions.
6c) Adjusting the
Potentiometer

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430Page 07.045.16
Technical Manual
DICTAMAT OpenDo
OFF ON
6. Setting the Desired Functions - cont.
Abb. 16
The DIP switches can be used to configure the operating modes listed
in 6a, among others. Please always make sure to carry out changes in
the de-energized state!
6d) Setting the DIP
Switches
Switch Description OFF ON
1 Function Semi-
automatic Automatic
2 Deadman Deactivated Activated
3 Push & Go Deactivated Activated
4Behaviour in
case of obstacle Reversing Stop
5 Closing speed 50 % Full
6Door leaf max.
80 kg Deactivated Activated
7Door leaf max.
60 kg Deactivated Activated
8Door leaf max.
40 kg Deactivated Activated
1. In semi-automatic mode, the door operator does not close
automatically. The hold-open time set at potentiometer P1 is ignored.
In automatic mode, the door operator closes after the hold-open
time set at potentiometer P1.
2. In deadman mode the door drive only runs as long as the
operator push-button is pressed.
If DIP switch 2 is set to ON, the position of DIP switch 1 is
ignored!
If DIP switch 2 is set to OFF, the settings of DIP switch 1 apply.
3. When Push & Go is activated, the door drive starts moving auto-
matically as soon as the door is pushed. Only possible in OPEN
direction!
4. If reversing is active, the door drive moves in the opposite
direction if an obstacle is detected during the closing
movement. During the opening movement, the drive stops.
When reversing, the drive always moves at reduced speed.
If DIP switch 4 is set to ON (STOP), the drive stops when an obstacle
is detected, both during opening and closing.
Fig. 16

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430 Page 07.045.17
Technical Manual
DICTAMAT OpenDo
After all desired settings have been made via the potentiometer and the
DIP switches, they must be accepted via the reset button.
IMPORTANT: If commissioning has not yet been carried out, please
jump to point 7 (page 07.021.18). The settings are also adopted by
the commissioning.
To adopt the settings after commissioning and during operation, the
following steps must be taken:
• Press the reset button for approx. 2 s.
→ LED starts flashing red continuously. The controller is in
configuration mode.
• If not already done, set the desired configuration. Then press
the reset button for less than 0.5 s. The controller exits the
configuration mode.
→ LED starts flashing red twice in quick succession with a
pause of 1.5 s. The control unit is in start state.
• Now perform a movement in any direction. The door drive moves
in creep speed.
→ The red LED goes out, the configuration has been accepted.
6. Setting the Desired Functions - cont.
5. This setting refers to the closing speed of the DIP switches 6 - 8. In
position OFF the closing speed is only 50 % of the speed set in 6 - 8.
6. to 8.
The closing speed to be set refers to the weight of the door leaf:
6. Weight of door leaf max. 80 kg → 20 cm/s
7. Weight of door leaf max. 60 kg → 23 cm/s
8. Weight of door leaf max. 40 kg → 25 cm/s
6d) Setting the DIP
Switches - cont.
6e) Accepting the
Settings

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430Page 07.045.18
Technical Manual
DICTAMAT OpenDo
To put the DICTAMAT OpenDointo operation a complete reset must be
carried out. This reset also takes over previously configured settings, so
step 6e, "Accepting the settings" is not necessary.
The following steps must be carried out for the reset:
• Connect the controller to the power supply
→ LED starts flashing red twice in quick succession with a
1.5s pause.
• Press reset button for approx. 2 s.
→ LED starts flashing red continuously.
• Check direction of rotation. Open with OPEN button or close with
CLOSE button. If the running direction is wrong:
→ Turn motor cable and check direction of rotation again. For
this purpose the power supply must be disconnected beforehand!
• Move the door leaf to the middle position with the keys. Now
press the reset button again for approx. 2 s.
• The red LED is now permanently lit. The yellow LED lights up
during motor activity.
The drive moves to the end position Open.
The drive moves to end position Closed.
The drive moves to end position Open.
• The LEDs go out, now the desired functions can still be checked. If
these functions work, commissioning is now complete.
7. Commissioning
CAUTION!
Danger from moving door!
The door moves automatically during commissioning.
Please keep the danger area clear during commissioning.

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430 Page 07.045.19
Technical Manual
DICTAMAT OpenDo
8. Error Indication
Error Description Code*
Unknown error There is an unknown cause of
error. 1
Self-test - Multiple errors The self-test has detected
several errors. 2
Self-test - Oscillator error Defective oscillator 4
Self-test - Relay defective Defective relay 5
Self-test - Driver defective Defective driver 6
Self-test - Current
measurement defective
Current measurement does
not function properly. 7
Self-test - Driver error
detection defective
The performance driver
no longer issues an error
message.
8
Hardware - Encoder error The encoder is not correctly
connected or defective. 9
Hardware - Voltage not
permissible
The supply voltage is outside
the permissible range. 10
Memory - RAM defective A defect in the RAM was
detected. 11
Memory - ROM defective The program memory was
changed or is defective. 12
Memory - EEPROM
defective The data memory is defective. 13
*The red and green LEDs indicate the respective detected error. First the red
LED flashes quickly, then it is permanently lit for approx. 20 s. The green LED
flashes according to the error code. The cycle is repeated until the error is
reset.
4 s 20 s
Example for error code 4
In case of a defect, please always contact our technical support, if
possible with information about the code.

© DICTATOR Technik GmbH • Gutenbergstr. 9 • 86356 Neusäß • Germany
Tel. [phone] • Fax [phone] • E-mail [e-mail] • 20200430Page 07.045.20
Technical Manual
DICTAMAT OpenDo
9. Maintenance
• Device switched off
»Clean the moving parts.
»Check the toothed belt tension.
»Clean the sensors.
»Check the stability of the sliding door operator and make sure
that all screws are tightly screwed.
»Check whether all components are still aligned.
• Device switched on
»Check that the door is stable and that there is no friction during
movement.
»Check functions for correctness or check correct operation of all
functions.
»Check whether the resulting forces comply with the current
standards (e.g. in escape routes).
Component Functional
description
Possible wear
characteristics
Maintenance
interval
Replacement
interval
Idler pulley
Guides
toothed belt in
the system
Cracks;
slip;
wear
6 months after
installation,
then annually.
Every 10
years*
Wheel cover
Cover to
protect the
toothed wheel
Cracks;
slip;
wear
6 months after
installation,
then annually.
**
Toothed belt Power
transmission
Cracks/
notches;
elongation;
discoloration
6 months after
installation,
then annually.
Every 2
years*
Motor Force
transducer
Frequent error
messages
6 months after
installation,
then annually.
**
Wheel
hangers
Door
hanger and
movement
Deposits/dirt
on door or
rail
6 months after
installation,
then annually.
**
* Depends on the type of use
** Only recommended if the function is no longer ensured due to visible wear.