SMART TamperProof TL-2100S Product manual

1 2
TL-2100S FallGuard™ Safety Auto-Reset™ Seat Belt
SEAT BELT PLACEMENT
• Unscrew the one screw on either side of the wheelchair that holds the seat
in place.
• Attach the seat belt to the wheelchair by lining up the grommet holes on
the seat belt with the screw hole and re-insert screws through both the
seat belt and the wheelchair to hold the seat belt in place. Make sure the
screws are tightened.
• Adjust the seat belt to the desired length using the black buckle that holds
the adjustment strap in place.
• Place the monitor out of the reach of the resident. The suitable mounting
location is the back of the wheelchair, so that the resident cannot tamper
with the monitor.
TEST THE SYSTEM
• Buckle and unbuckle the seat belt to set o the alert. The monitor is now
active.The alert will sound whenever the seat belt is unbuckled.
• When the system is activated, press the“Reset”button on front of the
monitor to silence the alert.
Bed Sensor Pads
BED PLACEMENT.
• Place the pad under the resident’s shoulders to be
alerted when the resident sits up in the bed.
• Place the pad under the resident’s lower back/buttocks to
be alerted when the resident vacates the bed.
• Place the monitor out of reach of the resident. Suitable
mounting locations include: the back of headboard, the wall
or under the bed. Make sure the resident cannot tamper with
the monitor.
TEST THE SYSTEM
• Plug the pad into the monitor and apply pressure
to the pad to activate the system.The monitor will beep
twice when active.
• The alert will sound when pressure is released
from the pad. Press the“Reset”button on the front of the
monitor to silence the alert.
Chair Sensor Pads
WHEELCHAIR/CHAIR PLACEMENT
• Center the pad on the chair seat.
• Place the monitor out of reach of the resident. Suitable mounting locations
include: the back or handle of the wheelchair. Make sure the resident
cannot tamper with the monitor.
TEST THE SYSTEM
• Plug the pad into the monitor and apply pressure to the pad to activate
the system. The monitor will beep twice when active.
• The alert will sound when pressure is released from the pad.
Press the“Reset”button on front of the monitor to silence the alert.
Floor Mats
FLOOR MAT PLACEMENT
• Place the Floor Mat in the desired location such as a critical doorway or
next to a bed.
• Place the monitor out of the reach of the resident.
TEST THE SYSTEM
• Step on the Floor Mat to set o the alert. The monitor is now active.
The system will sound any time weight is on the Floor Mat.
• When the system is activated, press the“Reset”button on front of the
monitor to silence the alert.
SMART CAREGIVER CORPORATION
1229 North McDowell Blvd., Petaluma, CA. 94954 | Tel: [phone]
[e-mail] | www.smartcaregiver.com
Need Set-up Help? [phone]
ChangePadIndicator
Reset
Status
CheckPad
LowBattery
Pad&Monitor
ActivewhenBlinking
Bed Pad
SafetyAuto-Reset™
Reset
Status
CheckPad
LowBattery
Pad&Monitor
ActivewhenBlinking
CoBed Pad
SafetyAuto-Reset
VisualAlert
Status
CheckPad
LowBattery
Pad&Monitor
ActivewhenBlinking
SafetyAuto-Reset
Reset
Status
CheckPad
LowBattery
Pad&Monitor
ActivewhenBlinking
SafetyAuto-Reset
Reset
Status
CheckPad
LowBattery
Pad&Monitor
ActivewhenBlinking
Floor Mat
SafetyAuto-Reset
Reset
Status
PadLost
LowBattery
Pad&Monitor
ActivewhenBlinking
Floor Mat
SafetyAuto-Reset
Reset
Status
PadLost
LowBattery
Pad&Monitor
ActivewhenBlinking
CAUTION:If using this monitor with the Change Pad Indicator™ Timed Sensor Pads, this monitor will not indicate when pad life has expired. The pads will still function normally. Call [phone] for more information.
WARNING: Failure to comply with the warning may result in injury or death. This device is not suitable for all individuals. Other devices may be required.This device is not a substitute for visual monitoring by a caregiver. The
manufacturer does not claim that this device will stop elopement and/or stop falls.This device is designed to augment caregivers’ comprehensive resident mobility management program. Test this device before each use. Read the
instructions and Legal Disclaimer.
The Smart Caregiver Corporation TL-2100S Monitor is designed to be installed by the end-user. As such, it is the entire responsibility of the buyer to insure that the system is properly installed and tested. Further, the system is not designed to
replace good caregiving practices including, but not limited to:
A.) Direct patient supervision
B.) Adequate training for sta personnel for fall prevention and elopement
C.) Testing of the system before each use
WHERE PERMISSIBLE, IT ISTHE SELLER’S INTENT TO LIMIT ANY LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL ECONOMIC DAMAGES TO REFUND OFTHE PURCHASE PRICE OR REPLACEMENT OF THE GOODS. SELLER DISCLAIMS ANY
LIABILITY FOR COMPENSATORY OR OTHER DAMAGES ARISING OUT OF THE USE OF THE GOODS.
WARNING: The manufacturer does not claim that this device will stop elopement and/or stop falls.This device is designed to augment caregivers’ comprehensive resident mobility management program. This product is to be used by a
licensed caregiver only.
Protective Boot may contain trace amount of chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.
Limited Warranty: Seller warrants that the goods sold will be free from defects of workmanship and manufacturing, for a period of one year from the date of sale. Other than this limited warranty, seller makes no express or implied
warranties. Except for this limited warranty, NO EXPRESS OR IMPLIED WARRANTIES ARE GIVEN AND NO AFFIRMATION OF SELLER, BYWORDS OR ACTION, WILL CONSTITUTE A WARRANTY. THE GOODS BEING PURCHASED ARE BEING
SOLD ON A“WITH ALL FAULTS”BASIS.THE ENTIRE RISK AS TOTHE QUALITY AND PERFORMANCE OF THE GOODS ISWITH THE BUYER. SHOULDTHE GOODS PROVE DEFECTIVE FOLLOWINGTHEIR PURCHASE, THE BUYER, AND NOT THE
MANUFACTURER, DISTRIBUTOR OR RETAILER, ASSUMESTHE ENTIRE COST OF ALL NECESSARY INSTALLATION, SERVICING OR REPAIRS.
Installation and Use Instructions
Safety Auto-Reset™
Fall Monitor
• Pad Lost light alerts caregivers when a
pad is disconnected
with included Caregiver Key™
Patented Technology
TL-2100S R5 4-5-19
CE marking concerning medical appliances.
Device in contact with patient, excluding the heart area.
Follow the user manual instructions.
Protected against the ingress of foreign object ≥ 12.5mm &
against dripping water when tilted up to 15°.
Environment conditions of transport and storage between uses:
Temperature: -25°C to +70°C ;
Humidity: < 93% RH non-condensing
Environment operating conditions:
Temperature: 5°C to +40°C ;
Humidity: 15% to 93% RH non-condensing
Pressure: 700hPa to 1060hPa
Please contribute to protect the environment
by observing the disposal instructions.
Caution: Read the instructions for use.
TL-2100S
R5

Install 3 AA
Batteries
123
5
4
Mounting the TL-2100S
Mounting screws
in headboard
or wall.
Monitor may be mounted to a bed or a chair with the included locking mounting strap.
Hang the monitor on
the screws using the
mounting holes on
back of the monitor.
1 2
Test the system. (A) Put pressure on the sensor pad to activate the pad and
the fall monitor.The fall monitor will beep two times to indicate that the
sensor pad and the fall monitor are in use. The“Status”light will blink when
pressure is on the pad. (B) When pressure is removed, the fall monitor will
sound the alert tone. Press the reset button to silence the alert .
Test the System - Pressure Pads
A.
Reset
Button
Connect the Pressure Pad
A.
B.
Quick Start Instructions Need Set-up Help? [phone]
SMART CAREGIVER CORPORATION Tel: [phone] | www.smartcaregiver.com
Bottom of monitor
The battery compartment
door is secured with the
included Phillips-head screw
Test the System -
Floor Mats Reset
Button
Step on the oor mat.
The alert will sound. Press the Reset button to silence and reset the monitor.
Pinch the cord together
and route it through the
strain relief recess.
Plug the cord
into the monitor.
Note: SafeTRelease™ cords will not t into the strain relief recess.
Resetting the Monitor/ Tamper Proof ™Mode with Caregiver Key™(Optional)
Caregivers can choose to reset the
TL-2100S in either of two ways:
Select either “Reset Button ON” or
“Reset Button OFF, Use Caregiver
Key™ To Turn OFF”with the switch on
the side of the TL-2100S Fall Monitor.
1. Press the Reset button on the front
of the monitor (“Reset Button ON”
mode).
2. Insert optional Caregiver Key™ into
hole on the front of the monitor. (“Reset
Button OFF, Use Caregiver Key™ To
Turn OFF” mode).
This mode allows only the caregiver
to reset the monitor.
“Reset Button ON”Mode
Press the Reset button to reset the
monitor.
“Reset Button OFF, Use Caregiver Key™ To Turn OFF” Mode.
Insert optional Caregiver Key™ into hole on the front of the monitor.
For more information about the
Caregiver Key™and how it can be
used in your facility’s Fall Assessment
Program call 800-650-3637
Alert Volume
Adjustment
Tone
Adjustment
Alert Delay
Adjustment
TL-2100S R5
Warning: Failureto comply with warning may result in injury or death. This device is not suitable for all individuals.O ther devices may be required.This device is not a substitute for visual monitoring by caregiver. S ensor pad fall monitorsare prone to diculties. Be sure cord cannot entangle or chokethe user.The manufacturer does not claim that this device will stop elopement and/or stop falls. Thisdevice is designed to agument caregivers comprehensive residentmobility management program. Test this device before each use. Read the instructions and legal disclaimer. Read Instructions Before Use: Battery not included. Use 3 x AA alkaline Batteries. Set Up: Plug sensor pad into the fall monitor. Apply pressure to the sensor pad to test the system. The monitorwill emit t wo beeps, indicating that the system is working.The Monitor Status LED will blink every 3 seconds when the system is activated and operating properly.
Delay
2sec 1sec 0sec3 2 1 Dcrease/Increase
Volume
Tone
Bed Sensor Pad
Bed Sensor Pad
Safety Auto-Reset™
Pad
Lost
Low
Battery
Monitor Status
Active When Blinking
Pad and Monitor
Reset
Refer to User Instructions before changing this setting.
Reset Button-
ON
Reset Button OFF
Use Caregiver Key
To Turn OFF
6V DC 300mA MAX
-
FLOOR MAT
Safety Auto-Reset™
Pad
Lost
Low
Battery
Monitor Status
Active When Blinking
Pad and Monitor
Reset
B.
Close battery door and secure
it with small Philips-head
screw.
Place monitor back into its
plastic protective boot.
This product is shipped in the TAMPER PROOF Mode. The CK-02 Key
must be used to reset monitor in this mode. If Reset Button is to be
used, you must move switch on side of monitor.